Formaldehyde Emissions from Urea-Formaldehyde– and No-Added-Formaldehyde–Bonded Particleboard as Influenced by Temperature and Relative Humidity
Source abstract
Abstract
ABSTRACT It is well documented that temperature and humidity can influence formaldehyde emissions from composite panels that are produced using urea-formaldehyde (UF)–type adhesives. This work investigates the effect of temperature and humidity on newer commercial California Air Resources Board (CARB) phase II–compliant particleboard produced with UF-type adhesives. These results were compared with laboratory particleboards prepared with the no-added-formaldehyde (NAF) Soyad adhesive technology. A modified version of EN 717‐3 (“Formaldehyde Release by the Flask Method,” ÖNORM 1996) was used to collect formaldehyde emissions that were quantified using the acetylacetone method. The formaldehyde emissions from the commercial particleboard panel bonded with a UF-type resin increased greatly when panels were exposed to higher heat and humidity than in normal testing protocols. Furthermore, the rate of emission for these UF-bonded panels increased with longer exposure at 100 percent relative humidity. In contrast, formaldehyde emissions from particleboard bonded with the NAF adhesive were relatively stable and significantly lower compared with those bonded with UF at all temperature and relative humidity conditions. This work highlights the potential for increased long-term formaldehyde emissions even from the new UF CARB phase II–compliant adhesive systems.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Advanced Polymer Synthesis and Characterization · Photopolymerization techniques and applications · Advanced Chemical Sensor Technologies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (28)
Show source-provided references
1. Allen, A. J., B. K. Spraul, and J. M. Wescott. 2010. Improved CARB II-compliant soy adhesives for laminates. In:International Conference on Wood Adhesives 2009, C. R. Frihart, C. G. Hunt, and R. J. Moon(Eds.), September 28–30, 2010, South Lake Tahoe, California; Forest Products Society, Madison, Wisconsin. pp. 186–194.
2. American National Standards Institute (ANSI). 2009a. American National Standard for particleboard. A208.1‐2009. The Composite Panel Association, Gaithersburg, Maryland.
3. American National Standards Institute (ANSI). 2009b. American National Standard for medium density fiberboard (MDF) for interior applications. A208.2‐2009. The Composite Panel Association, Gaithersburg, Maryland.
4. American National Standards Institute (ANSI)/Hardwood Plywood and Veneer Association (HPVA). 2004. American National Standard for hardwood plywood and decorative plywood. HP-1‐2004. HPVA, Reston, Virginia.
5. ASTM International. 2002. Standard test method for determining formaldehyde concentrations in air and emission rates from wood products using a large chamber. E1333‐96. ASTM International, West Conshohocken, Pennsylvania.
6. ASTM International. 2008. Standard test method for determining formaldehyde concentration in air from wood products using a small scale chamber. D6007‐02. ASTM International, West Conshohocken, Pennsylvania.
7. Belman, S. 1963. The fluorimetric determination of formaldehyde. Anal. Chim. Acta29:120.
8. Birkeland, M. J., L. Lorenz, J. M. Wescott, and C. R. Frihart. 2010. Determination of native (wood derived) formaldehyde by the desiccator method in particleboards generated during panel production. Holzforschung64:429–433.
9. Cai, Z., M. Birkeland, J. M. Wescott, J. O'Dell, and J. E. Winandy. 2009. Effects of press sizes on internal steam pressure during particleboard hot-pressing process. Forest Prod. J.59:40–44.
10. California Air Resources Board. 2009. Airborne toxic control measure to reduce formaldehyde emissions from composite wood products. Health and Safety Code: Title 17, California Code of Regulations, Section 93120–93120.12.
11. Dunky, M. 2005. Resins for ultra-low formaldehyde emission according to the Japanese F**** quality. In:International Conference on Wood Adhesives 2005, November 2–4, 2005, San Diego, California; Forest Products Society, Madison, Wisconsin. pp. 343–349.
12. Frihart, C. R., J. M. Wescott, M. J. Birkeland, and K. M. Gonner. 2010. Formaldehyde emissions from ULEF- and NAF-bonded commercial hardwood plywood as influenced by temperature and relative humidity. Paper WS-23. In:Proceedings of the International Convention of Society of Wood Science and Technology and United Nations Economic Commission for Europe—Timber Committee, October 11–14, 2010, Geneva; Society of Wood Science and Technology, Monona, Wisconsin. 13 pp.
13. Kelly, T. S. 1996. Determination of formaldehyde and toluene diisocyanate emissions from indoor residential sources. Final Report. CARB Contract No. 93‐315. California Air Resources Board, Sacramento. 119 pp.
14. Meyer, B. 1979. Urea-Formaldehyde Resins. Addison-Wesley Publishing Company, Reading, Massachusetts. pp. 128–129.
15. Myers, G. E. 1985. The effects of temperature and humidity on formaldehyde emission from UF-bonded boards: A literature critique. Forest Prod. J. 35(9):20–31.
16. Myers, G. E. 1986 a. Resin hydrolysis and mechanisms of formaldehyde release from bonded wood products. In:Proceedings 47344, Wood Adhesives in 1985: Status and Needs, A. W. Christiansen, R. Gillespie, G. E. Myers, and B. H. River(Eds.), May 14–16, 1985, Madison, Wisconsin; Forest Products Research Society, Madison, Wisconsin. pp. 119–156.
17. Myers, G. E. 1986 b. Mechanisms of formaldehyde release from bonded wood products. In:ACS Symposium Series 316, Formaldehyde Release from Wood Products, B. Meyer, B. A. Andrews Kottes, and R. M. Reinhardt, April 28–May 3, 1985, Miami Beach, Florida; American Chemical Society, Washington, D.C. pp. 87–106.
18. Myers, G. E. and M. Nagaoka. 1981. Formaldehyde emission: Methods of measurement and effects of several particleboard variables. Wood Sci. 13:140–150.
19. Nash, T. 1953. Colorimetric estimation of formaldehyde by means of the Hantzch reaction. Biochem. J. 55:416–421.
20. Österreichisches Normungsinstitut (ÖNORM). 1992. Wood based panels—Determination of formaldehyde content—Extraction method called the perforator method. EN 120. ÖNORM, Vienna. pp. 5–6.
21. Österreichisches Normungsinstitut (ÖNORM). 1996. Wood based panels—Determination of formaldehyde content—Part 3: Formaldehyde release by the flask method. EN 717‐3. ÖNORM, Vienna.
22. Österreichisches Normungsinstitut (ÖNORM). 2002. Wood-based panels for use in construction—Characteristics, evaluation of conformity and marking. EN 13986. European Committee for Standardizations, Brussels.
23. Pizzi, A. 2003. Amino resin wood adhesives. In:Handbook of Adhesive Technology. A. Pizziand K. L. Mittal(Eds.). Marcel Dekker, New York. pp. 541–572.
24. Roffael, E. 2006. Volatile organic compounds and formaldehyde in nature, wood and wood based panels. Holz Roh- Werkst. 64:144–149.
25. Schäfer, M. and E. Roffael. 2000. On the formaldehyde release of wood. Holz Roh- Werkst. 58:259–264.
26. US Congress. 2010. Formaldehyde Standards for Composite Wood Products Act amended to the Toxic Substances Control Act of 1976. 111th Congress, 2nd session, §1660, 15 U.S.C. 2601 §601 (2010).
27. Wescott, J. M., M. J. Birkeland, J. Yarvoski, and R. Brady. 2010. Recent advances in soy containing PB and MDF. In:International Conference on Wood Adhesives 2009, C. R. Frihart, C. G. Hunt, and R. J. Moon(Eds.), September 28–30, 2009, South Lake Tahoe, California; Forest Products Society, Madison, Wisconsin. pp. 146–151.
28. Wexler, A. 1961. Humidity standards. TAPPI J. 44(6):180A.