Effect of Knots and Related Grain Deviation on the Rolling Shear in Dimension Lumber Used in Cross-Laminated Timber Transverse Core Layers
Source abstract
Abstract
Abstract Cross-laminated timber (CLT) technology has the potential for utilization of lower grades and underused species of lumber, because the core layers perpendicular to the principal loading direction transfer loads through shear, which is not correlated to the grade of lumber. Currently the product standard specifies the minimum grade requirements for all lumber to be used as CLT laminations. In this study, the effect of the presence of knots in the transverse core layer of CLT billets was examined in matched CLT samples where the heavy presence of knots and the related grain disturbance in the transverse core layer were the only variables compared with knot-free reference. All samples were tested as short beams in three-point bending and all failed in rolling shear in the transverse core layer. The presence of knots had no measurable effect on the shear capacity or stiffness of the tested CLT beam samples.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Wood Treatment and Properties · Tree Root and Stability Studies · Mechanical Behavior of Composites
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
The authors are, respectively, Graduate Student, École Nationale Supérieure des Technol. et Industries du Bois (ENSTIB), Épinal, France (t.grandvuinet@gmail.com); and Professor, Dept. of Wood Sci. and Engineering, Oregon State Univ., Corvallis (Lech.Muszynski@oregonstate.edu [corresponding author]). Thibault Grandvuinet is currently Wood Engineer, Atelier Volet SA, Lausanne, Switzerland. This paper was received for publication in August 2016. Article no. 16-00042.
References (13)
Show source-provided references
1. Aicher, S. and G. Dill-Langer. 2000. Basic considerations to rolling shear modulus in wooden boards. Otto-Graff J. 11:157–166.
2. American National Standards Institute/APA The Engineered Wood Association (ANSI/APA). 2012. Standard for performance-rated cross-laminated timber. ANSI/APA PRG 320‐2012. APA The Engineered Wood Association, Tacoma, Washington. p. 23.
3. ASTM International. 2013. Standard test methods for mechanical properties of lumber and wood-base structural material. ASTM D4761‐13. ASTM International, West Conshohocken, Pennsylvania. p. 11.
4. ASTM International. 2015. Standard test methods of static tests of lumber in structural sizes. ASTM D198‐15. ASTM International, West Conshohocken, Pennsylvania. p. 28.
5. Fellmoser, P. and H. J. Blaß. 2004. Influence of rolling shear modulus on strength and stiffness of structural bonded timber elements. In:Proceedings of the International Council for Research and Innovation in Building and Construction, Working Commission W18 - Timber Structures, August 2004, Edinburgh; University of Karlsruhe, Germany. 8pp.
6. Gupta, R., C. Batista, and S. M. Kent. 2004. Effect of knots on longitudinal shear strength of Douglas-fir using shear blocks. Forest Prod. J. 54(11):77–83.
7. Hochreiner, G., J. Füssl, E. Serrano, and J. Eberhardsteiner. 2014. Influence of wooden board strength class on the performance of cross-laminated timber plates investigated by means of full-field deformation measurements. Strain50(2):161–173.
8. Mohammad, M., S. Gagnon, B. K. Douglas, and L. Podesto. 2012. Introduction to cross-laminated timber. Wood Des. Focus22(2):1–12.
9. Muthe, B. P. and R. L. Ethington. 1968. Method for evaluating shear properties of wood. US Department of Agriculture Forest Products Laboratory Report, FPL-RN-0195. USDA Forest Products Laboratory, Madison, Wisconsin. p. 21.
10. Nie, X. 2015. Failure mechanism of rolling shear failure in cross-laminated timber. Master's thesis. The University of British Columbia, Vancouver, Canada.
11. Norlin, P. L., M. C. Norlin, and F. Lam. 1999. Shear behaviour of laminated Douglas fir veneer. Wood Sci. Technol. 33(3):199–208.
12. Ross, L. A., S. Gagnon, and E. Keith. 2012. Structural design of cross-laminated timber elements. In: CLT Handbook: Cross-Laminated Timber, U.S. Edition. E. Karacabeyliand B. Douglas (Eds.). FPInnovations, Pointe-Claire, Quebec, Canada.
13. Zhou, Q. Y., M. Gong, Y. H. Chui, and M. Mohammad. 2014. Measurement of rolling shear modulus and strength of cross-laminated timber using bending and two-plate shear tests. Wood Fiber Sci. 46(2):1–11.