Soil fabric of coarse-grained soils sedimented under water and its relation to relative density and excess pore water pressure
Source abstract
Abstract
Abstract The soil fabric varies significantly depending on the deposition process that forms the grain skeleton. Each deposition method produces a specific type of soil fabric, which can be linked to a particular soil density. When represented as relative density, determined using limit densities from standard index tests, a wide range of relative densities can be observed for different sands produced by the same deposition method. The influence of this variation in relative density, resulting from a single deposition method, on the development of the excess pore water pressure (PWP) should be further investigated. A fast testing of the excess PWP accumulation in sandy soils during undrained cyclic shearing can be easily performed using the newly developed PWP Tester. In the PWP Tester, specimens are prepared through sedimentation in water, which yields a comparable fabric in different sands but significantly different relative densities. Despite these relative density differences, the rate of the excess PWP evolution during undrained shearing is remarkably similar among different sands. This indicates that relative density should not be regarded as a primary factor influencing the development of the excess PWP and that the soil fabric plays equal or even a greater role.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Geotechnical Engineering and Soil Mechanics · Soil and Unsaturated Flow · Geotechnical Engineering and Soil Stabilization
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (32)
Show source-provided references
1. Oda, M.: Initial fabrics and their relations to mechanical properties of granular material. Soils Found. 12(1), 17–36 (1972). https://doi.org/10.3208/sandf1960.12.1710.3208/sandf1960.12.17 ↗
2. Oda, M., Konishi, J., Nemat-Nasser, S.: Some experimentally based fundamental results on the mechanical behaviour of granular materials. Géotechnique 30(4), 479–495 (1980). https://doi.org/10.1680/geot.1980.30.4.47910.1680/geot.1980.30.4.479 ↗
3. Oda, M., Nemat-Nasser, S., Konishi, J.: Stress-induced anisotropy in granular masses. Soils Found. 25(3), 85–97 (1985). https://doi.org/10.3208/sandf1972.25.3_8510.3208/sandf1972.25.3_85 ↗
4. Oda, M.: The mechanism of fabric changes during compressional deformation of sand. Soils Found. 12(2), 1–18 (1972). https://doi.org/10.3208/sandf1972.12.110.3208/sandf1972.12.1 ↗
5. Ochiai, H., Lade, P.V.: Three-dimensional behavior of sand with anisotropic fabric. J. Geotech. Eng. 109(10), 1313–1328 (1983). https://doi.org/10.1061/(asce)0733-9410(1983)109:10(1313)10.1061/(asce)0733-9410(1983)109:10(1313) ↗
6. Miura, S., Toki, S.: Anisotropy in mechanical properties and its simulation of sands sampled from natural deposits. Soils Found. 24(3), 69–84 (1984). https://doi.org/10.3208/sandf1972.24.3_6910.3208/sandf1972.24.3_69 ↗
7. Yang, Z.X., Li, X.S., Yang, J.: Quantifying and modelling fabric anisotropy of granular soils. Géotechnique 58(4), 237–248 (2008). https://doi.org/10.1680/geot.2008.58.4.23710.1680/geot.2008.58.4.237 ↗
8. Sun, Q., Zheng, J., He, H., Li, Z.: Characterizing fabric anisotropy of air-pluviated sands. E3S Web Conf. 92, 01003 (2019). https://doi.org/10.1051/e3sconf/2019920100310.1051/e3sconf/20199201003 ↗
9. Ni, X., Ma, J., Sakaguchi, H., Zhang, F.: Fabric characteristics of in situ sand with/without liquefaction verified by anisotropy of magnetic susceptibility. J. Rock Mech. Geotech. Eng. 15(5), 1274–1283 (2022). https://doi.org/10.1016/j.jrmge.2022.09.00310.1016/j.jrmge.2022.09.003 ↗
10. Oda, M., Koishikawa, I., Higuchi, T.: Experimental study of anisotropic shear strength of sand by plane strain test. Soils Found. 18(1), 25–38 (1978). https://doi.org/10.3208/sandf1972.18.2510.3208/sandf1972.18.25 ↗
11. Ladd, R.: Preparing test specimens using undercompaction. Geotech. Test. J. 1(1), 16 (1978). https://doi.org/10.1520/gtj10364j10.1520/gtj10364j ↗
12. Mulilis, J.P., Arulanandan, K., Mitchell, J.K., Chan, C.K., Seed, H.B.: Effects of sample preparation on sand liquefaction. J. Geotech. Geoenviron. Eng. 103, 91–108 (1977). https://doi.org/10.1061/AJGEB6.000038710.1061/AJGEB6.0000387 ↗
13. Sze, H.Y., Yang, J.: Failure modes of sand in undrained cyclic loading: impact of sample preparation. J. Geotech. Geoenviron. Eng. 140(1), 152–169 (2014). https://doi.org/10.1061/(ASCE)GT.1943-5606.000097110.1061/(ASCE)GT.1943-5606.0000971 ↗
14. Ishihara, K.: Liquefaction and flow failure during earthquakes. Géotechnique 43(3), 351–451 (1993). https://doi.org/10.1680/geot.1993.43.3.35110.1680/geot.1993.43.3.351 ↗
15. Ishihara, K., Silver, M.L., Kitagawa, H.: Cyclic strength of undisturbed sands obtained by a piston sampler. Soils Found. 19(3), 61–76 (1979)10.3208/sandf1972.19.3_61 ↗
16. Tatsuoka, F., Ochi, K., Fujii, S., Okamoto, M.: Cyclic undrained triaxial and torsional shear strength of sands for different sample preparation methods. Soils Found. 26(3), 23–41 (1986). https://doi.org/10.3208/sandf1972.26.3_2310.3208/sandf1972.26.3_23 ↗
17. Nagase, H., Ishihara, K.: Effects of load irregularity on the cyclic behaviour of sand. Soil Dyn. Earthq. Eng. 6(4), 239–249 (1987)10.1016/0267-7261(87)90005-4 ↗
18. Hatanaka, M., Uchida, A., Oh-oka, H.: Correlation between the liquefaction strengths of saturated sands obtained by in-situ freezing method and rotary-type triple tube method. Soils Found. 35(2), 67–75 (1995)10.3208/sandf1972.35.2_67 ↗
19. Oda, M., Kawamoto, K., Suzuki, K., Fujimori, H., Sato, M.: Microstructural interpretation on reliquefaction of saturated granular soils under cyclic loading. J. Geotech. Geoenviron. Eng. 127(5), 416 (2001). https://doi.org/10.1061/(ASCE)1090-0241(2001)127:5(416)10.1061/(ASCE)1090-0241(2001)127:5(416) ↗
20. Hatanaka, M., Feng, L., Matsumura, N., Yasu, H.: A study on the engineering properties of sand improved by the sand compaction pile method. Soils Found. 48(1), 73–85 (2008)10.3208/sandf.48.73 ↗
21. Ahmadi, M.M., Akbari Paydar, N.: Requirements for soil-specific correlation between shear wave velocity and liquefaction resistance of sands. Soil Dyn. Earthq. Eng. 57, 152–163 (2014)10.1016/j.soildyn.2013.11.001 ↗
22. Wichtmann, T., Triantafyllidis, T.: An experimental database for the development, calibration and verification of constitutive models for sand with focus to cyclic loading: part I— tests with monotonic loading and stress cycles. Acta Geotech. 11(4), 739–761 (2015). https://doi.org/10.1007/s11440-015-0402-z10.1007/s11440-015-0402-z ↗
23. Seed, H.B., Idriss, I.M.: Simplified procedure for evaluating soil liquefaction potential. J. Soil Mech. Found. Div. 97(9), 1249–1273 (1971). https://doi.org/10.1061/jsfeaq.000166210.1061/jsfeaq.0001662 ↗
24. Bacic, B., Herle, I.: A simple method for the determination of sensitivity to density changes in sand liquefaction. Open Geomech. 2, 1–8 (2020). https://doi.org/10.5802/ogeo.610.5802/ogeo.6 ↗
25. Baćić, B., Herle, I.: Density-dependent pore water pressure evolution in a simplified cyclic shear test. Int. J. Geosynth. Ground Eng. 9(4), 47 (2023). https://doi.org/10.1007/s40891-023-00469-410.1007/s40891-023-00469-4 ↗
26. Bacic, B., Herle, I.: Vereinfachter zyklischer scherversuch zum PWD-Aufbau in grobkörnigen Böden. Geotechnik 46(4), 210 (2023). https://doi.org/10.1002/gete.20230000410.1002/gete.202300004 ↗
27. Baćić, B.: PWP tester–a simplified cyclic shear test for pore water pressure evolution in granular soils. TU Dresden, Dresden (2024)
28. NABau: DIN 18126: Baugrund, Untersuchung Von Bodenproben–Bestimmung der Dichte Nichtbindiger Böden Bei Lockerster und Dichtester Lagerung. Beuth Verlag GmbH, Berlin (2022)
29. Cubrinovski, M., Ishihara, K.: Maximum and minimum void ratio characteristics of sands. Soils Found. 42(6), 65–78 (2002)10.3208/sandf.42.6_65 ↗
30. ...Stamati, O., Andò, E., Roubin, E., Cailletaud, R., Wiebicke, M., Pinzon, G., Couture, C., Hurley, R., Caulk, R., Caillerie, D., Matsushima, T., Bésuelle, P., Bertoni, F., Arnaud, T., Laborin, A., Rorato, R., Sun, Y., Tengattini, A., Okubadejo, O., Colliat, J.-B., Saadatfar, M., Garcia, F., Papazoglou, C., Vego, I., Brisard, S., Dijkstra, J., Birmpilis, G.: spam: Software for practical analysis of materials. J. Open Source Softw. 5(51), 2286 (2020). https://doi.org/10.21105/joss.0228610.21105/joss.02286 ↗
31. Wiebicke, M., Andò, E., Šmilauer, V., Herle, I., Viggiani, G.: A benchmark strategy for the experimental measurement of contact fabric. Granul. Matter 21(3), 54 (2019). https://doi.org/10.1007/s10035-019-0902-x10.1007/s10035-019-0902-x ↗
32. BSI: ISO 13322-2: Particle Size Analysis. Image Analysis Methods: Part 2 Dynamic Image Analysis Methods. British Standards Institution, London (2020)