Controlling the synthesis conditions for the fabrication of Pb (Mg1/3Nb2/3) O3 nano powders to diminish undesirable pyrochlore structure
Source abstract
Abstract
Abstract The main problem in fabrication of relaxor lead magnesium niobate (PMN; Pb(Mg1/3Nb2/3) O3) material is the formation of an undesirable pyrochlore phase (Pb1.86Mg0.24Nb1.67O6.5). This phase significantly impacts the electrical properties of the compound. Therefore, this article presents various experimental trials performed to minimize the formation of the undesirable pyrochlore phase during the preparation of relaxor lead magnesium niobate material. In this regard, a sol-gel pathway was utilized. The synthesis was conducted as follows; niobium ethoxide, metal nitrate and metal acetate were combined with 2-methoxyethanol to form transparent solution. The gel was then formed by heating the solution at 80 °C, to form the precursor powder. Subsequently, thermal treatment at elevated temperatures was performed to form the perovskite structure. The effects of several synthesis conditions such as the presence of surplus Mg2+ ions, excess of Pb2+ ion content, annealing and pre-annealing temperature, type of fuel and the annealing time, on the physicochemical properties and the structure of PMN phase were investigated. Thermal gravimetric analysis (TGA) results manifested that crystallization of PMN was occurred at a temperature of 580 °C. X-ray diffraction (XRD) profiles revealed that the ratio of the pyrochlore (Pb1.86Mg0.24Nb1.67O6.5) phase was significantly reduced by increasing the Mg2+ ion content up to 30%. The lowest concentration of the pyrochlore phase was predestined during a single annealing step at 900 °C for a period of 3 h, using an excess of 30% Mg2+ ion concentration. Rietveld refinement of the XRD data was conducted using Material Analysis Using Diffraction (MAUD) software. The refinement was performed to determine the crystal structure and lattice constants. From the refinement, the cubic structure was evinced with a lattice constant (a) of 4.048Å. Fourier transform infrared (FT-IR) spectroscopy of PMN nano powders annealed at 900 °C for 3 h demonstrated a spectrum characteristic of the most perovskite compounds with a common BO6 oxygen-octahedral structure. Additionally, X-ray photoelectron spectrum (XPS) provided the composition and the chemical states of the prepared PMN compound. Brunauer–Emmett–Teller (BET) surface area analysis revealed that the PMN material exhibited a large specific surface area (155.8 m2/g) with a small average pore radius (2.8 nm). High-resolution transmission electron microscopy (HR-TEM) images indicated that the PMN particles manifested a regular cubic structure with an average particle size of 43 ± 0.1 nm under the optimum conditions. The selected area electron diffraction (SAED) technique proved the polycrystalline nature of the formed ceramic material. From characterization results obtained in this work, this material shows potential candidate for various metrological applications, including piezoceramic for the ultrasonic transducer cores.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Ferroelectric and Piezoelectric Materials · Microwave Dielectric Ceramics Synthesis · Nuclear materials and radiation effects
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (44)
Show source-provided references
1. K. Zheng et al., 3D printed piezoelectric focused element for ultrasonic transducer. Ceram. Int. 2, 1–7 (2024). https://doi.org/10.1016/j.ceramint.2024.02.22410.1016/j.ceramint.2024.02.224 ↗
2. C. Liu, X. Wang, G. Wu, Investigation of performance dependence on transduction diaphragm design for piezoelectric micromachined ultrasonic transducers. Microelectron. J. 150, 1–7 (2024). https://doi.org/10.1016/j.mejo.2024.10626010.1016/j.mejo.2024.106260 ↗
3. J. Wang et al., Fabrication and properties of the thickness mode ultrasonic transducer based on 0.15Pb(Mg1/3Nb2/3)O3-0.38PbHfO3-0.47PbTiO3 piezoelectric ceramics. Ceram. Int. 46(8), 11913–11920 (2020). https://doi.org/10.1016/j.ceramint.2020.01.22810.1016/j.ceramint.2020.01.228 ↗
4. K. Sarkar, V. Kumar, S. Mukherjee, Synthesis and investigation of properties of nanostructured cubic PMN ceramics for possible applications in electronics. J. Mater. Sci. Mater. Electron. 31(17), 14314–14321 (2020). https://doi.org/10.1007/s10854-020-03988-210.1007/s10854-020-03988-2 ↗
5. T. Dippong, E. Levei, D. Toloman, L. Barbu-tudoran, O. Cadar, Investigation on the formation, structural and photocatalytic properties of mixed Mn-Zn ferrites nanoparticles embedded in SiO2 matrix. J. Anal. Appl. Pyrol. 158, 1–8 (2021). https://doi.org/10.1016/j.jaap.2021.10528110.1016/j.jaap.2021.105281 ↗
6. T. Dippong, D. Toloman, M. Dan, E. Andrea, O. Cadar, Structural, morphological and photocatalytic properties of Ni-Mn ferrites: influence of the Ni:Mn ratio. J. Alloys Compd. 913, 1–9 (2022). https://doi.org/10.1016/j.jallcom.2022.16512910.1016/j.jallcom.2022.165129 ↗
7. T. Dippong, M. Stoia, study on the obtaining of cobalt oxides by thermal decomposition of some complex combinations, undis- persed and dispersed in sio2 matrix, J. Therm. Anal. Calorim., vol. 94, pp. 389–393, 200810.1007/s10973-008-9111-2 ↗
8. T. Zheng, J. Wu, D. Xiao, J. Zhu, Recent development in lead-free perovskite piezoelectric bulk materials, Prog. Mater. Sci., vol. 98, no. September 2017, pp. 552–624, 2018, https://doi.org/10.1016/j.pmatsci.2018.06.00210.1016/j.pmatsci.2018.06.002 ↗
9. C. Mn, O. Fe, T. Dippong, E. Andrea, C. Leostean, O. Cadar, Impact of annealing temperature and ferrite content embedded in SiO2 matrix on the structure, morphology and magnetic characteristics of (Co0.4Mn0.6Fe2O4)δ (SiO2)100-δ nanocomposites. J. Alloys Compd. 868, 159203 (2021). https://doi.org/10.1016/j.jallcom.2021.15920310.1016/j.jallcom.2021.159203 ↗
10. S. Zhang et al., Recent developments in piezoelectric crystals. J. Korean Ceram. Soc. 55(5), 419–439 (2018). https://doi.org/10.4191/kcers.2018.55.5.1210.4191/kcers.2018.55.5.12 ↗
11. H.J. Lee, S. Zhang, Y. Bar-Cohen, S. Sherrit, High temperature, high power piezoelectric composite transducers. Sensors. 14(8), 14526–14552 (2014). https://doi.org/10.3390/s14081452610.3390/s140814526 ↗
12. T. Stevenson et al., Piezoelectric materials for high temperature transducers and actuators. J. Mater. Sci. Mater. Electron. 26(12), 9256–9267 (2015). https://doi.org/10.1007/s10854-015-3629-410.1007/s10854-015-3629-4 ↗
13. S. Mishra, L. Unnikrishnan, S.K. Nayak, S. Mohanty, Advances in Piezoelectric Polymer composites for Energy Harvesting Applications: a systematic review. Macromol. Mater. Eng. 304(1), 1–25 (2019). https://doi.org/10.1002/mame.20180046310.1002/mame.201800463 ↗
14. Z. Liu, H. Wu, W. Ren, Z. Ye, Piezoelectric and Ferroelectric Materials: Fundamentals, Recent Progress, and Applications Piezoelectric and Ferroelectric Materials: Fundamentals, Recent Progress, and Applications, in Comprehensive Inorganic Chemistry III, 3rd edn. (Elsevier Inc., 2022), pp. 1–3710.1016/B978-0-12-823144-9.00069-8 ↗
15. Z. Shujun, Advantages and challenges of Relaxor-PbTiO3 ferroelectric crystals for Electroacoustic Transducers- A Review. Prog Mater. Sci. 68(1), 1–124 (2015). https://doi.org/10.1038/jid.2014.37110.1038/jid.2014.371 ↗
16. T. Rojac, Piezoelectric response of disordered lead-based relaxor ferroelectrics. Commun. Mater. 4(12), 1–7 (2023). https://doi.org/10.1038/s43246-023-00336-910.1038/s43246-023-00336-9 ↗
17. M. Arzenšek et al., Origins of the large piezoelectric response of doped lead magnesium niobate– lead titanate ceramics. Sci. Adv. 10, 1–14 (2024). https://doi.org/10.1126/sciadv.adp089510.1126/sciadv.adp0895 ↗
18. P. Kumar, C. Prakash, T.C. Goel, Dielectric and electrostrictive properties of PMNT near MPB. Sci. Technol. Adv. Mater. 8, 463–468 (2007). https://doi.org/10.1016/j.stam.2007.05.00710.1016/j.stam.2007.05.007 ↗
19. P. Moetakef, Z.A. Nemati, Study of microstructure and dielectric properties of PMN-PZT ceramics via a mixed powder method including sol-gel precursor. J. Alloys Compd. 476, 1–2 (2009). https://doi.org/10.1016/j.jallcom.2008.09.13610.1016/j.jallcom.2008.09.136 ↗
20. M. Ghasemifard, S.M. Hosseini, G.H. Khorrami, Synthesis and structure of PMN-PT ceramic nanopowder free from pyrochlore phase. Ceram. Int. 35, 2899–2905 (2009). https://doi.org/10.1016/j.ceramint.2009.03.03610.1016/j.ceramint.2009.03.036 ↗
21. Z. Wei, Y. Huang, T. Tsuboi, Y. Nakai, J. Zeng, G. Li, Optical characteristics of Er 3+-doped PMN-PT transparent ceramics. Ceram. Int. 38(4), 3397–3402 (2012). https://doi.org/10.1016/j.ceramint.2011.12.05110.1016/j.ceramint.2011.12.051 ↗
22. H.S. Hsu et al., PMN-PT-PZT composite films for high frequency ultrasonic transducer applications. Sens. Actuators Phys. 179, 121–124 (2012). https://doi.org/10.1016/j.sna.2012.02.03110.1016/j.sna.2012.02.031 ↗
23. C. Kornphom, A. Laowanidwatana, T. Bongkarn, Fabrication of Pyrochlore Phase Free PMN-PZT ceramics via the Combustion technique. Integr. Ferroelectr. 165(1), 11–18 (2015). https://doi.org/10.1080/10584587.2015.106233810.1080/10584587.2015.1062338 ↗
24. S. Kashyap, S.C. Bhatt, M. Uniyal, G.S. Kathait, Structural and dielectric properties of Lead Magnesium Niobate and Ti-doped Lead Magnesium Niobate at room temperature, Mater. Today Proc., vol. 28, pp. 28–31, 2020, https://doi.org/10.1016/j.matpr.2020.01.03210.1016/j.matpr.2020.01.032 ↗
25. G.H. Jaffari, J. Tanvir, F. Mumtaz, W. Ali, G. Yuan, Polymorphic and morphotropic phase transitions in pb(Mg1/3Nb2/3)O3–PbTiO3 solid solutions. Ceram. Int. 46(14), 22482–22491 (2020). https://doi.org/10.1016/j.ceramint.2020.06.00710.1016/j.ceramint.2020.06.007 ↗
26. A. Berksoy-Yavuz, E. Mensur-Alkoy, E. Erdem, S. Alkoy, Electrical properties, EPR analyses and defect chemistry of Mn-doped 0.675PMN-0.325PT piezoceramics. Ceram. Int. 46(18), 28980–28986 (2020). https://doi.org/10.1016/j.ceramint.2020.08.06910.1016/j.ceramint.2020.08.069 ↗
27. E.C. Chuan, Piezoelectric, ferroelectric and pyroelectric properties of (100– x)pb(Mg1/3Nb2/3)O3– xxPbTiO3 ceramics. J. Adv. Dielectr. 12(3), 1–6 (2022). https://doi.org/10.1142/S2010135X2250002310.1142/S2010135X22500023 ↗
28. P. Moetakef, Z.A. Nemati, Synthesis of PMN pyrochlore free ceramics via a modified mixed oxide method. J. Electroceram. 19, 207–213 (2007). https://doi.org/10.1007/s10832-007-9320-210.1007/s10832-007-9320-2 ↗
29. G. Mohamed, A. Elhefnawy, M. El-gazery, A. El-razek, M.M. Rashad, A.H. Khafagy, Improvement of the structural, dielectric, nanopowder features for ultrasonic applications. Ferroelectrics. 615(1), 8–28 (2023). https://doi.org/10.1080/00150193.2023.224355910.1080/00150193.2023.2243559 ↗
30. C.A. Guarany et al., Preparation of pyrochlore-free PMN by an alternative chemical method. Ferroelectrics. 334, 147–155 (2006). https://doi.org/10.1080/0015019060069429010.1080/00150190600694290 ↗
31. A. Kumar, A. Roy, Structural and electromechanical characterization of lead magnesium niobate-lead titanate (PMN-0.3PT) piezoceramic for energy harvesting applications. Appl. Phys. 1, 1–23 (2022)
32. W. Liu, Y. Cao, J. Wang, Y. Wang, X. Xi, J. Yang, Piezoelectric properties of 3– 1 type porous PMN-PZT ceramics doped with strodium. Mater. Sci. Eng. B 263, 1–5 (2021). https://doi.org/10.1016/j.mseb.2020.11484710.1016/j.mseb.2020.114847 ↗
33. S.M. Gupta, A.R. Kulkarni, S.K. Kulkarni, Surface study of lead magnesium niobate ceramic: using X-ray photoelectron spectroscopy. Mater. Sci. Eng. 39, 34–40 (1996)10.1016/0921-5107(95)01524-8 ↗
34. R. Yimnirun, E. Meechoowas, S. Ananta, T. Tunkasiri, Mechanical properties of x PMN- (1-x) PZT ceramic systems. C J. 3(2), 147–154 (2004)
35. H. Wang et al., Preparation and characterization of pyrochlore-free 0.655Pb (Mg1/3Nb2/3)O3-0.345PbTiO3 piezoelectric ceramics by tape-casting process. Ferroelectrics. 536(1), 170–180 (2018). https://doi.org/10.1080/00150193.2018.154070010.1080/00150193.2018.1540700 ↗
36. H. Zhou et al., Enhanced thermal stability and large piezoelectric properties of Sm-doped pb(Sc1/2Nb1/2)O3–Pb(Mg1/3Nb2/3)O3–PbTiO3 multifunctional ceramics. J. Mater. Sci. 56(21), 12121–12131 (2021). https://doi.org/10.1007/s10853-021-06053-310.1007/s10853-021-06053-3 ↗
37. M. Ghasemifard, S.M. Hosseini, M.M. Bagheri-Mohagheghi, N. Shahtahmasbi, Structure comparison of PMN-PT and PMN-PZT nanocrystals prepared by gel-combustion method at optimized temperatures. Phys. E Low-Dimensional Syst. Nanostruct. 41(9), 1701–1706 (2009). https://doi.org/10.1016/j.physe.2009.06.00710.1016/j.physe.2009.06.007 ↗
38. M. Prabu, I.B.S. Banu, S. Gobalakrishnan, M. Chavali, S. Umapathy, Synthesis and Optical characterization of lead zirconate titanate (52/48) powders by Sol–Gel Method. Adv. Sci. Eng. Med. 5(5), 496–499 (2014). https://doi.org/10.1166/asem.2013.128010.1166/asem.2013.1280 ↗
39. E.A. Eid, M.R. Ebied, M.A. Kaid, M.G.S. Ali, Synthesis and microstructure characterization of sol-gel derived phase fractions in PZT nanopowders. Dig. J. Nanomater Biostructures. 15, 465–470 (2020)10.15251/DJNB.2020.152.465 ↗
40. S. Mansour, A. Eid, L. Abd, E.M. Rashad, M. Afifi, J. Turner, Dielectric and piezoelectric performance of gadolinium-doped lead lanthanum zirconate titanate. Appl. Ceram. Technol. 15, 766–774 (2017). https://doi.org/10.1111/ijac.1283510.1111/ijac.12835 ↗
41. J. Cao, L. Li, Z. Gui, An XPS study on the degradation of lead magnesium niobate-based relaxor ferroelectrics during nickel electroplating. J. Mater. Chem. 11, 1198–1200 (2001). https://doi.org/10.1039/b006953l10.1039/b006953l ↗
42. X. Jiang, F. Zheng, X. Tian, Y. Liu, T. Yang, M. Cheng, Investigation on the fabrication and properties of Ce- doped PMN – PT translucent piezoelectric ceramics. J. Mater. Sci. Mater. Electron. 33(1), 468–478 (2022). https://doi.org/10.1007/s10854-021-07320-410.1007/s10854-021-07320-4 ↗
43. E.M. Jayasingh, K. Prabhakaran, R. Sooraj, C. Durgaprasad, S.C. Sharma, Synthesis of pyrochlore free PMN-PT powder by partial oxalate process route. Ceram. Int. 35, 591–596 (2009). https://doi.org/10.1016/j.ceramint.2008.01.02210.1016/j.ceramint.2008.01.022 ↗
44. S.E.E. Profile, Hydrogen permeation using nanostructured silica membranes. Trans. Ecol. Environ. 193, 447–465 (2016). https://doi.org/10.2495/SDP15038110.2495/SDP150381 ↗