journal article·2025-12Open access

Laser-assisted substrate heating for crack mitigation in laser metal deposition

Yorihiro Yamashita, Seiya Kamo, Yuji Sato, Keisuke Takenaka, Tomomasa Ohkubo, Masahiro Tsukamoto

Applied Physics A· Volume 131· Issue 12

Abstract

Abstract Laser Metal Deposition (LMD) is widely applied for repairing components and reinforcing molds and tools due to its ability to locally deposit metal onto target materials. However, when cemented carbides are deposited onto steel substrates, the mismatch in material properties and rapid thermal cycling often lead to crack formation in the overlay. To address this issue, this study investigates the effect of localized laser heating of the substrate during the LMD process on crack suppression. A multi-beam laser powder deposition system equipped with dual laser beams was employed, allowing simultaneous cladding and substrate heating. WC–12 wt% Co powder was deposited onto S50C steel while varying the output power and irradiation position of the substrate heating laser. Crack formation was evaluated using digital microscopy, and microstructural changes were analyzed through Vickers hardness testing and SEM observation. Additionally, numerical simulations based on the two-dimensional heat conduction equation were performed to analyze temperature histories under different heating conditions. The results revealed that crack formation was most effectively suppressed when the substrate heating laser was positioned 0.5 mm from the cladding path and operated at output power of 30 W or higher. Under these conditions, dendritic structures appeared in the overlay, suggesting a change in solidification behavior. Thermal simulations showed that substrate heating led to a more gradual temperature decrease after the peak, particularly at 50 W and 0.5 mm offset, indicating a reduced cooling rate. These findings demonstrate that localized laser heating of the substrate during cladding effectively reduces thermal strain by lowering the cooling rate, thereby contributing to crack suppression.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Additive Manufacturing Materials and Processes · High Entropy Alloys Studies · Advanced materials and composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (24)

Show source-provided references
1. D. Svetlizky, B. Zheng, A. Vyatskikh, M. Das, S. Bose, A. Bandyopadhyay, J.M. Schoenung, E.J. Lavernia, N. Eliaz, Laser-based directed energy deposition (DED-LB) of advanced materials. Materials Science and Engineering: A 840, 142967 (2022)10.1016/j.msea.2022.142967 ↗
2. D.-G. Ahn, Directed energy deposition (DED) process: state of the art. International Journal of Precision Engineering and Manufacturing-Green Technology 8, 703–742 (2021)10.1007/s40684-020-00302-7 ↗
3. S.M. Thompson, L. Bian, N. Shamsaei, A. Yadollahi, An overview of direct laser deposition for additive manufacturing; part I: transport phenomena, modeling and diagnostics. Addit. Manuf. 8, 36–62 (2015)
4. T. DebRoy, H.L. Wei, J.S. Zuback, T. Mukherjee, J.W. Elmer, J.O. Milewski, A.M. Beese, A. Wilson-Heid, A. De, W. Zhang, Additive manufacturing of metallic components – process, structure and properties. Prog. Mater. Sci. 92, 112–224 (2018)10.1016/j.pmatsci.2017.10.001 ↗
5. J. Schneider, A. Norman, J. Gumpinger, F. Brückner, M. Bavdaz, C. Leyens, T. Ghidini, Additive manufacturing of a metallic optical bench—process development, material qualification and demonstration. Ceas Space J. 15, 55–68 (2023)10.1007/s12567-021-00409-w ↗
6. T. Petrat, C. Brunner-Schwer, B. Graf, M. Rethmeier, Microstructure of Inconel 718 parts with constant mass energy input in laser-based direct energy deposition. Procedia Manuf. 36, 256–266 (2019)10.1016/j.promfg.2019.08.033 ↗
7. F. Brueckner, M. Riede, M. Müller, F. Marquardt, R. Willner, A. Seidel, E. López, C. Leyens, E. Beyer, Enhanced manufacturing possibilities using multi–materials in laser metal deposition. J. Laser Appl. 30(3), 032308 (2018)10.2351/1.5040639 ↗
8. J. Bennett, D. Garcia, M. Kendrick, T. Hartman, G. Hyatt, K. Ehmann, F. You, J. Cao, Repairing automotive dies with directed energy deposition: industrial application and life cycle analysis. J. Manuf. Sci. Eng. 141(2), 021019 (2019)10.1115/1.4042078 ↗
9. C. Mills, Y. Faqiri, H.J. Maier, T. Hassel, Enhancing bearing lifespan with load–adapted hybrid components via laser–based directed energy deposition repair. Int. J. Adv. Manuf. Technol. 137, 5521–5534 (2025)10.1007/s00170-025-15480-4 ↗
10. S. Shrestha, R.P. Panakarajupally, M. Kannan, G. Morscher, A.L. Gyekenyesi, O.E. Scott-Emuakpor, Analysis of microstructure and mechanical properties of additive repaired Ti–6Al–4V by direct energy deposition. Materials Science and Engineering: A 806, 140604 (2021)10.1016/j.msea.2020.140604 ↗
11. N. D’Souza, S. Ravichandran, S. Donovan, P. Daum, R. Morrell, Z. Nye, R.J. Lancaster, On the design optimisation of direct energy deposited support structures to repair aero–engine turbine segments. Addit. Manuf. 56, 102905 (2022)
12. Y. Yamashita, M. Nakamura, T. Kunimine, Y. Sato, Y. Funada, M. Tsukamoto, Effects of WC ratios on bead size and crack initiation in forming WC–Co cemented carbides by laser metal deposition. J. Laser Appl. 35(4), 042010 (2023)10.2351/7.0001101 ↗
13. K.-W. Kim, A.B. Kale, Y.-H. Cho, S.-H. Park, K.-A. Lee, Microstructural and wear properties of WC–12Co cemented carbide fabricated by direct energy deposition. Wear 518–519, 204653 (2023)10.1016/j.wear.2023.204653 ↗
14. Y. Yamashita, K.A. Ilman, T. Kunimine, Y. Sato, Temperature evaluation of cladding beads and the surrounding area during the laser metal deposition process. J. Manuf. Mater. Process. 7(6), 192 (2023)
15. M. Ostolaza, A. Zabala, J.I. Arrizubieta, I. Llavori, N. Otegi, A. Lamikiz, High-temperature tribological performance of functionally graded stellite 6/WC metal matrix composite coatings manufactured by laser–directed energy deposition. Friction 12(3), 522–538 (2024)10.1007/s40544-023-0790-2 ↗
16. T. Kunimine, R. Miyazaki, Y. Yamashita, Y. Funada, Effects of laser-beam defocus on microstructural features of compositionally graded WC/Co-alloy composites additively manufactured by multi-beam laser directed energy deposition. Sci. Rep. 10, 8975 (2020)10.1038/s41598-020-65429-8 ↗
17. Y. Yamashita, K. Kawabata, H. Mori, E. Ose, T. Kunimine, Influence of laser energy variation on the composition and properties of gradient-structured cemented carbide layers produced by LP-DED. J. Manuf. Mater. Process. 9(7), 218 (2025)
18. M.A. Gulov, I.E. Vitoshkin, A.A. Filippov, A.P. Zavyalov, A.G. Malikov, Influence of substrate preheating on the structural and phase composition of a nickel-based cermet coating. J. Appl. Mech. Tech. Phys. 64(6), 954–958 (2023)10.1134/S0021894423060020 ↗
19. H.-. Wang, Y.-. Cheng, J.-. Yang, X. Liang -b, Microstructure and properties of Fe based amorphous coatings deposited by laser cladding under different preheating temperatures. J. Non-cryst. Solids. 602, 122081 (2023)10.1016/j.jnoncrysol.2022.122081 ↗
20. Y. Sato, M. Tsukamoto, T. Shobu, Y. Funada, Y. Yamashita, T. Hara, M. Sengoku, Y. Sakon, T. Ohkubo, M. Yoshida, N. Abe, In situ X-ray observations of pure-copper layer formation with blue direct diode lasers. Appl. Surf. Sci. 480, 861–867 (2019)10.1016/j.apsusc.2019.03.057 ↗
21. Y. Sato, K. Ono, K. Takenaka, K. Morimoto, Y. Funada, Y. Yamashita, T. Ohkubo, N. Abe, M. Tsukamoto, Fabrication of pure copper rod by multi-beam laser metal deposition with blue diode lasers. J. Laser Micro/Nanoeng.16(3), 189–193 (2021)
22. The Japan Society of Mechanical Engineers (JSME), JSME Data Book: Heat Transfer, 5th edn. (Maruzen Publishing, Tokyo, Japan, 2009)
23. S.K. Lam, A. Pitrou, S. Seibert. Numba: a LLVM-based python JIT compiler. Proceedings of the Second Workshop on the LLVM Compiler Infrastructure in HPC; 2015.10.1145/2833157.2833162 ↗
24. A. Sadhu, A. Choudhary, S. Sarkar, A.M. Nair, P. Nayak, S.D. Pawar, G. Muvvala, S.K. Pal, A. Nath, K. A study on the influence of substrate pre-heating on mitigation of cracks in direct metal laser deposition of NiCrSiBC-60%WC ceramic coating on inconel 718. Surface & Coatings Technol. 389, 125646 (2020)10.1016/j.surfcoat.2020.125646 ↗