journal article·2026-01

Tuning mechanical and microstructural properties of Bi-2212 ceramics through optimal Nd³⁺ substitution: findings from experimental and theoretical approach

B. Akkurt, A. S. Erturk, A. T. Ulgen, Y. C. Demir, M. B. Turkoz, U. Erdem, G. Yildirim

Applied Physics A· Volume 132· Issue 1
Publisher page

Abstract

This study systematically investigates the mechanical and structural behavior of Nd3+-substituted Bi2.0-xNdxSr2.0Ca1.0Cu2.0Oy ceramics synthesized by the conventional solid-state reaction method using combined experimental microhardness (Hv) testing and theoretical modeling approaches. Incorporating Nd ions into the Bi-2212 lattice enhances microstructural stability, grain boundary coupling, and crystallographic coherence, with optimal mechanical performance at x = 0.01. Complementary SEM, XRD, and EDX analyses confirm the correlation between improved surface morphology, crystallinity, and enhanced mechanical performance. EDX results further verified the successful replacement of Bi3+ for Nd3+ and compositional uniformity within the Bi-2212 lattice, supporting the structural integrity and hardness improvements. At this concentration, strong ionic and partial covalent bonding interactions between Nd3+ and the host lattice facilitate charge compensation, defect accommodation, and densification, resulting in superior Vickers hardness and resistance to deformation. As for the mechanical characterization examination, indentation behavior reveals classical Indentation Size Effect (ISE) behavior through all the synthesized compounds, with peak load resistance at x = 0.01 and marked degradation at higher dopant levels due to increased porosity, grain boundary decoupling, and strain localization. Bulk density (ρ) measurements correlate strongly with microhardness trends, confirming the interdependence of atomic packing, structural integrity, porosity, intergranular coherence, and mechanical durability. Accordingly, the optimal mechanical and structural performance is observed at x = 0.01, corresponding to the highest measured ρ value of 5.99 g/cm3 and Hv of 0.498 GPa at 0.295 N. These results indicate that Nd³⁺ substitution at this level promotes enhanced densification and grain boundary cohesion, leading to a defect-minimized microstructure with superior resistance to indentation and load-induced plastic deformation. Beyond this doping level, excessive Nd incorporation deteriorates crystallinity and promotes porosity formation, resulting in reduced mechanical durability and structural integrity. Consequently, the material exhibits increased susceptibility to load-induced plastic deformation and crack propagation along grain boundaries. At the highest substitution level, Hv decreases from 0.333 GPa to 0.280 GPa across the same range of applied loads, confirming the adverse impact of over-doping on mechanical performance. A near-linear relationship between ρ and Hv is observed, validating bulk density as a predictive metric for key mechanical design features in Bi-2212 systems. Additionally, key mechanical performance metrics, including load-independent Hv results, are analyzed within the plateau limit (PL) regions of Nd-substituted Bi-2212 structures using established theoretical models to elucidate structure-property relationships and predict service life and material reliability under practical application conditions. Comparative analysis reveals that the Indentation-Induced Cracking (IIC) model provides the most accurate description of the mechanical response in the doped systems. The experimental findings and theoretical results highlight the critical role of rare-earth substitution at an optimal concentration level in tuning lattice cohesion, defect tolerance, and mechanical resilience, establishing x = 0.01 for Nd/Bi-substituted Bi-2212 as a promising candidate for high-performance structural ceramic applications.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Physics of Superconductivity and Magnetism · Advanced ceramic materials synthesis · Ferroelectric and Piezoelectric Materials

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (59)

Show source-provided references
1. H. Kamerlingh Onnes, Further experiments with liquid helium. D. On the change of electrical resistance of pure metals at very low temperatures, etc. V. The disappearance of the resistance of mercury. K. Ned. Akad. Wet. Proc. Ser. B Phys. Sci. 14, 113–115 (1911)
2. T. Turgay, G. Yildirim, Effect of aliovalent Si/Bi partial substitution on propagation mechanisms of cracking and dislocation in Bi-2212 crystal system. J. Mater. Sci. Mater. Electron. 30(8), 7314–7323 (2019)10.1007/s10854-019-01044-2 ↗
3. M. Krishnan, J.J. Meng, B.Z. Li, Y. Ma, C. Wang, D. Bhoi, B. Liu, Superconducting ground state and electronic properties of σ-phase Ta–W–Mo–Re–Os high entropy alloys. J. Phys. Chem. Solids 202, 112630 (2025)10.1016/j.jpcs.2025.112630 ↗
4. E. Hannachi, K.A. Mahmoud, M.I. Sayyed, Y. Slimani, Effect of sintering conditions on the radiation shielding characteristics of YBCO superconducting ceramics. J. Phys. Chem. Solids 164, 110627 (2022)10.1016/j.jpcs.2022.110627 ↗
5. E. Kara, P. Özkurt, B. Özkurt, Effects of different dwell-times under low pelletization pressure on the physical properties of the Bi-2212 ceramics. J. Mater. Sci. Mater. Electron. 33(18), 14951–14960 (2022)10.1007/s10854-022-08412-5 ↗
6. Y. Slimani, M.A. Almessiere, E. Hannachi, M. Mumtaz, A. Manikandan, A. Baykal, F.B. Azzouz, Improvement of flux pinning ability by tungsten oxide nanoparticles added in YBa2Cu3Oy superconductor. Ceram. Int. 45(6), 6828–6835 (2019)10.1016/j.ceramint.2018.12.176 ↗
7. E. Hannachi, Y. Slimani, A. Ekicibil, A. Manikandan, F.B. Azzouz, Magneto-resistivity and magnetization investigations of YBCO superconductor added by nanowires and nanoparticles of titanium oxide. J. Mater. Sci. Mater. Electron. 30, 8805–8813 (2019)10.1007/s10854-019-01205-3 ↗
8. H. Fallah-Arani, A. Sedghi, S. Baghshahi, R.S. Moakhar, N. Riahi-Noori, N.J. Nodoushan, Bi-2223 superconductor ceramics added with cubic-shaped TiO2 nanoparticles: structural, microstructural, magnetic, and vortex pinning studies. J. Alloys Compd. 900, 163201 (2022)10.1016/j.jallcom.2021.163201 ↗
9. Y. Slimani, M.A. Almessiere, E. Hannachi, A. Baykal, A. Manikandan, M. Mumtaz, F.B. Azzouz, Influence of WO3 nanowires on structural, morphological and flux pinning ability of YBa2Cu3Oy superconductor. Ceram. Int. 45(2), 2621–2628 (2019)10.1016/j.ceramint.2018.10.201 ↗
10. P. Zagura, I. Kim, F. Follows, C. Barker, Z. Melhem, A. Twin, S. Ball, C. Grovenor, S. Speller, T. Mousavi, Development of persistent joints for superconducting Bi-2212 coils. Supercond. Sci. Technol. 37, 055003 (2024)10.1088/1361-6668/ad2b77 ↗
11. S.H. Jeong, J.B. Song, Y.H. Choi, S.G. Kim, B.S. Go, M. Park, H. Lee, Effect of micro-ceramic fillers in epoxy composites on thermal and electrical stabilities of GdBCO coils. Compos. Part. B 94, 190–196 (2016)10.1016/j.compositesb.2016.03.065 ↗
12. A. Xu, J. Jiang, C. Tarantini, F. Kametani, E. Hellstrom, D.C. Larbalestier, Flux pinning enhancement of Bi-2212 tapes by increasing Sr content. IEEE Trans. Appl. Supercond. 34(3), 1–5 (2024)
13. A. Harabor, P. Rotaru, N.A. Harabor, P. Nozar, A. Rotaru, Structural, thermal and superconducting properties of Ag2O -doped YBa2Cu3O7 − x composite materials. Ceram. Int. 49(9), 14904–14916 (2023)10.1016/j.ceramint.2022.08.100 ↗
14. S. Abdelhaleem, M.O. Alziyadi, A. Alruwaili, M.J. Alawi, A. Alkabsh, M.S. Shalaby, BSCCO high Tc-superconductor materials: strategies toward critical current density enhancement and future opportunities. Appl. Phys. A 131(2), 151 (2025)10.1007/s00339-025-08262-y ↗
15. M.S. Hassan, I.E. Mohamed, M. Matar, A.I. Abou-Aly, R. Awad, M. Anas, Effect of hard magnetic ferrite (Ba0.5Sr0.5Fe12O19) nanoparticles on the mechanical properties of the (Bi,Pb)-2223 phase. Appl. Phys. A 129(5), 333 (2023)10.1007/s00339-023-06557-6 ↗
16. A.K. Saxena, High-Temperature Superconductors, 2nd edn. (Springer, Heidelberg, New York, Dordrecht, London, 2012)10.1007/978-3-642-28481-6 ↗
17. T.P. Sheahen, Introduction to High-Temperature Superconductivity, 1st edn. (Kluwer Academic Publishers, New York, Boston, 2002)10.1007/b115100 ↗
18. E. Takayama-Muromachi, High-pressure synthesis of homologous series of high critical temperature (Tc) superconductors. Chem. Mater. 10(10), 2686–2698 (1998)10.1021/cm9802301 ↗
19. N. Plakida, High Temperature Cuprate Superconductors. Springer Ser. Solid-State SciSpringer, Berlin,. (2010), p. 480. ISBN 978364212632110.1007/978-3-642-12633-8 ↗
20. H. Hilgenkamp, J. Mannhart, Grain boundaries in high-Tc superconductors. Rev. Mod. Phys. 74(2), 485 (2002)10.1103/RevModPhys.74.485 ↗
21. K. Salama, V. Selvamanickam, L. Gao, K. Sun, High current density in bulk YBa2Cu3Ox superconductor. Appl. Phys. Lett. 54(23), 2352–2354 (1989)10.1063/1.101525 ↗
22. C. Autret-Lambert, B. Pignon, M. Gervais, I. Monot-Laffez, A. Ruyter, L. Ammor, F. Gervais, J.M. Bassat, R. Decourt, Microstructural and transport properties in substituted Bi2Sr2CaCu2O8+δ modulated compounds. J. Solid State Chem. 179(6), 1698–1706 (2006)10.1016/j.jssc.2006.03.005 ↗
23. M. Hasan, A.A. Hossain, ThIrGe superconductor: first-principles insights into the optoelectronic, mechanical stability, thermophysical, and superconducting properties. J. Phys. Chem. Solids 179, 111413 (2023)10.1016/j.jpcs.2023.111413 ↗
24. C.C. Tsuei, J.R. Kirtley, G. Hammerl, J. Mannhart, H. Raffy, Z.Z. Li, Doping effect on pairing symmetry in cuprate superconductors. J. Phys. Chem. Solids 67(1–3), 64–67 (2006)10.1016/j.jpcs.2005.10.041 ↗
25. J. Bardeen, L.N. Cooper, J.R. Schrieffer, Theory of superconductivity. Phys. Rev. 108(5), 1175 (1957)10.1103/PhysRev.108.1175 ↗
26. Y. Zhang, X. Xu, Predicting mechanical performance of starch-based foam materials. J. Cell. Plast. 58(3), 505–514 (2022)10.1177/0021955X211062638 ↗
27. Y. Zhang, X. Xu, Machine learning the lattice constant of cubic pyrochlore compounds. Int. J. Appl. Ceram. Technol. 18(3), 661–676 (2021)10.1111/ijac.13709 ↗
28. Y. Zhang, X. Xu, Machine learning lattice constants for cubic perovskite A2XY6 compounds. J. Solid State Chem. 291, 121558 (2020)
29. Y. Zhang, X. Xu, Predicting lattice parameters for orthorhombic distorted-perovskite oxides via machine learning. Solid State Sci. 113, 106541 (2021)10.1016/j.solidstatesciences.2021.106541 ↗
30. M. Rekaby, N.H. Mohammed, M. Ahmed, A.I. Abou-Aly, Synthesis, microstructure and indentation Vickers hardness for (Y3Fe5O12)x/Cu0.5Tl0.5Ba2Ca2Cu3O10–δ composites. Appl. Phys. A 128(4), 261 (2022)10.1007/s00339-022-05394-3 ↗
31. A.K. Saxena, High-Temperature Superconductors (Springer Science & Business Media, Berlin, 2012)10.1007/978-3-642-28481-6 ↗
32. X. Xu, J.H. Kim, S.X. Dou, S. Choi, J.H. Lee, H.W. Park, M. Rindfleish, M. Tomsic, A correlation between transport current density and grain connectivity in MgB2/Fe wire made from ball-milled boron. J. Appl. Phys. 105(10), 103913 (2009)
33. M. Krishnan, K. Ishigaki, S. Mariappan, R. Sokkalingam, J. Gouchi, D. Bhoi, A. Sonachalam, Evolution of superconducting and normal state properties of Fe1.09Se0.55Te0.45 under pressure. J. Phys. Chem. Solids 201, 112628 (2025)10.1016/j.jpcs.2025.112628 ↗
34. S. Cavdar, E. Deniz, H. Koralay, O. Ozturk, M. Erdem, A. Gunen, The effect of PbSe addition on the mechanical properties of Bi-2212 superconductors. J. Supercond. Nov. Magn. 25(7), 2297–2307 (2012)10.1007/s10948-012-1629-7 ↗
35. A.T. Ulgen, S. Çetin, Y. Zalaoglu, M.B. Turkoz, U. Erdem, G. Yildirim, Role of active slip systems induced with holmium impurity in Bi-2212 ceramics on mechanical design performance and morphological properties. Ceram. Int. 48(18), 26361–26369 (2022)10.1016/j.ceramint.2022.05.322 ↗
36. M. Dogruer, G. Yildirim, O. Ozturk, I. Belenli, C. Terzioglu, Variation of mechanical properties of Cr-doped Bi-2212 superconductors. J. Supercond. Nov. Magn. 26(9), 2949–2954 (2013)10.1007/s10948-013-2113-8 ↗
37. Y. Zalaoglu, E. Bekiroglu, M. Dogruer, G. Yildirim, O. Ozturk, C. Terzioglu, Comparative study on mechanical properties of undoped and Ce-doped Bi-2212 superconductors. J. Mater. Sci. Mater. Electron. 24(7), 2339–2345 (2013)10.1007/s10854-013-1098-1 ↗
38. H. Koralay, O. Hicyilmaz, S. Cavdar, E. Asikuzun, A.T. Tasci, O. Ozturk, Effect of Zn content on microstructure and mechanical performance in Bi1.8Sr2Ca2Cu3.2–xZnxO10+δ glass ceramic. J. Mater. Sci. Mater. Electron. 25(7), 3116–3126 (2014)10.1007/s10854-014-1992-1 ↗
39. B. Özkurt, The mechanical properties of Y-doped Bi-2223 superconductors. J. Supercond. Nov. Magn. 26(2), 261–266 (2013)10.1007/s10948-012-1801-0 ↗
40. F. Kahraman, Evaluation of the Vickers microhardness and fracture toughness on hot pressed Bi-2212/Ag ceramic composites. J. Mater. Sci. Mater. Electron. 27(8), 8006–8012 (2016)10.1007/s10854-016-4796-7 ↗
41. B. Özkurt, The influence of Na addition on the mechanical properties of Bi-2212 superconductors. J. Supercond. Nov. Magn. 27(11), 2407–2414 (2014)10.1007/s10948-014-2623-z ↗
42. U. Kölemen, O. Uzun, M. Yılmazlar, N. Güçlü, E. Yanmaz, Hardness and microstructural analysis of Bi1.6Pb0.4Sr2Ca2−xSmxCu3Oy polycrystalline superconductors. J. Alloys Compd. 415(1–2), 300–306 (2006)10.1016/j.jallcom.2005.09.023 ↗
43. D.H. Tran, A.T. Pham, N.H. Nam, K.X. Thuy, A.D. Truong, T. Le, V.C. Le, N.T.M. Hong, P. Hai, D.T.B. Hop, M. Dogruer, Effect of ZnFe2O4 addition on the phase stability, hardness and superconducting properties of Bi-2223 phase. Ceram. Int. 51(20, Part A), 30974–30983 (2025)10.1016/j.ceramint.2025.04.289 ↗
44. O. Ozturk, E. Asikuzun, M. Erdem, G. Yildirim, O. Yildiz, C. Terzioglu, The effect of Pr addition on superconducting and mechanical properties of Bi-2212 superconductors. J. Mater. Sci. Mater. Electron. 23(2), 511–519 (2012)10.1007/s10854-011-0429-3 ↗
45. U. Erdem, B. Akkurt, A.T. Ulgen, Y. Zalaoglu, T. Turgay, G. Yildirim, Effect of annealing ambient conditions on crack formation mechanisms of bulk Bi-2212 ceramic systems. J. Asian Ceram. Soc. 9(3), 1214–1227 (2021)10.1080/21870764.2021.1952746 ↗
46. G. Yildirim, Beginning point of metal to insulator transition for Bi-2223 superconducting matrix doped with Eu nanoparticles. J. Alloys Compd. 578, 526–535 (2013)10.1016/j.jallcom.2013.07.016 ↗
47. K. Kocabaş, M. Çiftçioğlu, The effect of Sb substitution of Cu in Bi1.7Pb0.3Sr2Ca2Cu3−xSbxOy superconductors. Phys. Status Solidi A 177(2), 539–545 (2000)10.1002/(SICI)1521-396X(200002)177:2<539::AID-PSSA539>3.0.CO;2-7 ↗
48. C.P. Jr. Poole, H.A. Farach, R.J. Creswick, R. Prozorov, Superconductivity. (Academic, New York, 1995), p. 154
49. R.R. Reddy, M. Murakami, S. Tanaka, P.V. Reddy, Elastic behavior of a Y–Ba–Cu–O sample prepared by the MPMG method. Physica C 257(1–2), 137–142 (1996)10.1016/0921-4534(95)00701-6 ↗
50. H. Kozuka, T. Umeda, J. Jin, T. Monde, S. Sakka, Application of sol–gel processing to preparation of high temperature superconducting materials. Bull. Inst. Chem. Res. Kyoto Univ. 66(2), 80–92 (1988)
51. M.L. Tarkanian, J.P. Neumann, L. Raymond, The Science of Hardness Testing and its Research Application (American Society for Metals, Metals Park, Ohio, 1973)
52. U. Erdem, G. Yildirim, M.B. Türköz, A.T. Ulgen, A. Mercan, Change in transition balance between durable tetragonal phase and stress-induced phase of cobalt surface-layered Bi-2212 materials by semi-empirical mechanical models. Phys. Scr. 98(7), 075702 (2023)10.1088/1402-4896/acdb04 ↗
53. Y. Zalaoglu, T. Turgay, A.T. Ulgen, U. Erdem, M.B. Turkoz, G. Yildirim, A novel research on the subject of the load-independent microhardness performances of Sr/Ti partial displacement in Bi-2212 ceramics. J. Mater. Sci. Mater. Electron. 31(24), 22239–22251 (2020)10.1007/s10854-020-04724-6 ↗
54. B.D. Michels, G.H. Frischat, Microhardness of chalcogenide glasses of the system Se–Ge–As. J. Mater. Sci. 17(2), 329–334 (1982)10.1007/BF00591466 ↗
55. F. Fröhlich, P. Grau, W. Grellmann, Performance and analysis of recording microhardness tests. Phys. Status Solidi A 42(1), 79–89 (1977)10.1002/pssa.2210420106 ↗
56. J. Gong, J. Wu, Z. Guan, Examination of the indentation size effect in low-load Vickers hardness testing of ceramics. J. Eur. Ceram. Soc. 19(15), 2625–2631 (1999)10.1016/S0955-2219(99)00043-6 ↗
57. C. Hays, E.G. Kendall, An analysis of Knoop microhardness. Metallography. 6, 275–366 (1973)10.1016/0026-0800(73)90053-0 ↗
58. B. Akkurt, G. Yildirim, Change of mechanical performance and characterization with replacement of Ca by Gd nanoparticles in Bi-2212 system and suppression of durable tetragonal phase by Gd. J. Mater. Sci. Mater. Electron. 27(12), 13034–13043 (2016)10.1007/s10854-016-5444-y ↗
59. H. Li, R.C. Bradt, The effect of indentation-induced cracking on the apparent microhardness. J. Mater. Sci. 31(4), 1065–1070 (1996)10.1007/BF00352908 ↗