journal article·2026-02Open access

Multi-Physics finite element modeling of PEEK in selective laser sintering: effects of laser power and scanning speed on thermal distribution and melt pool formations

Oğulcan Eren

Applied Physics A· Volume 132· Issue 2

Abstract

Abstract Selective Laser Sintering (SLS) of poly(ether ether ketone) (PEEK), a high-performance polymer, presents significant challenges due to its narrow processing window, high melting temperature, and low thermal conductivity in powder form. The successful fabrication of highly functional, dense components necessitates precise control over the intricate thermal and fluid dynamics governing the PEEK sintering process. However, experimental and single-physics modeling approaches are often insufficient to capture these transient multi-physics phenomena. This study introduces a novel two-dimensional (2D) multi-physics Finite Element Analysis (FEA) model to simulate the SLS processing of PEEK powder. This study realistically models the transient thermal and fluid behaviour during the SLS process and evaluates the effect of fundamental parameters such as laser power and scanning speed by incorporating combined multi-physical phenomena such as heat transfer, fluid dynamics, and phase transformations. Although optimum thermal profiles are obtained at an Energy Density (ED) of 0.03 J/mm², it has been determined that ED is not the single factor in understanding the thermal behavior. The results show that scan speed significantly regulates heat accumulation and thermal gradients. Slower scanning speeds promote high heat buildup and surface degradation at low powers, while higher speeds limit thermal penetration, increasing the temperature difference between the top and bottom surfaces. This computationally efficient 2D multi-physics approach improves understanding of PEEK laser sintering mechanisms, providing quantitative information for rapid and effective parameter identification in high-performance polymer additive manufacturing.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Additive Manufacturing and 3D Printing Technologies · Additive Manufacturing Materials and Processes · Injection Molding Process and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (42)

Show source-provided references
1. Y. Liu, F. Zhao, Y. Zhao, T. Shu, S. Liu, S. Wang, Y. Su, C. Sun, S.N. Varma, C. Liu, Build orientation effects on properties of SLS-printed PEEK for bone implants: surface-physical-mechanical characteristics and in vitro cellular responses. J. Mater. Res. Technol. (2025). https://doi.org/10.1016/j.jmrt.2025.09.16910.1016/j.jmrt.2025.09.169 ↗
2. M.H. Ali, N. Sabyrov, E. Shehab, Powder bed fusion–laser melting (PBF–LM) process: latest review of materials, process parameter optimization, application, and up-to-date innovative technologies. Prog. Addit. Manuf. 7(6), 1395–1422 (2022)10.1007/s40964-022-00311-9 ↗
3. Y. Yamauchi, T. Kigure, T. Niino, Optimization of penetration depth and powder layer thickness for proper interlayer adhesion in polymer laser sintering. 2022
4. S. Singh, D. Kaur, M. Singh, R. Balu, A. Mehta, H. Vasudev, Challenges and issues in manufacturing of components using polymer-based selective laser sintering (SLS): a review. Int. J. Interact. Des. Manuf. (IJIDeM) , 1–24 (2024)10.1007/s12008-024-02049-w ↗
5. Y. Wang, K. Chai, Y. Wang, Study on the temperature field distribution of the interface and process parameter optimization for selective laser sintering of PEEK. Polymer Engineering & Science 65(6), 3302–3318 (2025). https://doi.org/10.1002/pen.2721510.1002/pen.27215 ↗
6. M.M. Rahman, K.A. Ahmed, M. Karim, J. Hassan, R. Roy, B. Bustami, S.M.N. Alam, H. Younes, Optimization of selective laser sintering three-dimensional printing of thermoplastic polyurethane elastomer: a statistical approach. J. Manuf. Mater. Process. 7(4), 144 (2023)
7. A. Franco, M. Lanzetta, L. Romoli, Experimental analysis of selective laser sintering of polyamide powders: an energy perspective. J. Clean. Prod. 18(16–17), 1722–1730 (2010)10.1016/j.jclepro.2010.07.018 ↗
8. H.M. Yehia, A. Hamada, T.A. Sebaey, W. Abd-Elaziem, Selective laser sintering of polymers: process parameters, machine learning approaches, and future directions. J. Manuf. Mater. Process. 8(5), 197 (2024)
9. J. Borah, M. Chandrasekaran, Modeling and Optimization of 3D Printing Processes: A Literature Review. Rob. Autom. Healthc. , 95–114 (2024)10.1201/9781003424161-6 ↗
10. M. Schmid, R. Kleijnen, M. Vetterli, K. Wegener, Influence of the origin of polyamide 12 powder on the laser sintering process and laser sintered parts. Appl. Sci. 7(5), 462 (2017)10.3390/app7050462 ↗
11. M. Yuan, J.A. Galloway, R.J. Hoffman, S. Bhatt, Influence of molecular weight on rheological, thermal, and mechanical properties of PEEK. Polym. Eng. Sci. 51(1), 94–102 (2011)10.1002/pen.21785 ↗
12. J. Molinar-Díaz, A.J. Parsons, I. Ahmed, N.A. Warrior, L.T. Harper, Poly-ether-ether-ketone (PEEK) biomaterials and composites: challenges, progress, and opportunities. Polym. Rev. 65(2), 527–565 (2025)10.1080/15583724.2024.2406965 ↗
13. N. Yi, R. Davies, A. Chaplin, P. McCutchion, O. Ghita, Slow and fast crystallising poly aryl ether ketones (PAEKs) in 3D printing: crystallisation kinetics, morphology, and mechanical properties. Additive Manuf. 39, 101843 (2021)10.1016/j.addma.2021.101843 ↗
14. A. Curmi, A. Rochman, J. Buhagiar, Influence of polyether ether ketone (PEEK) viscosity on interlayer shear strength in screw extrusion additive manufacturing. Additive Manuf. 84, 104086 (2024)10.1016/j.addma.2024.104086 ↗
15. M. Schmidt, D. Pohle, T. Rechtenwald, Selective Laser Sintering of PEEK. CIRP Annals 56(1), 205–208 (2007). https://doi.org/10.1016/j.cirp.2007.05.09710.1016/j.cirp.2007.05.097 ↗
16. S. Berretta, Poly Ether Ether Ketone (PEEK) Polymers for High Temperature Laser Sintering (HT-LS) (University of Exeter (United Kingdom), 2015)10.1016/j.eurpolymj.2015.04.003 ↗
17. T. Kigure, Y. Yamauchi, T. Niino, Investigation into laser sintering of PEEK using commercially available low powder bed temperature machine. 2021
18. A. Mokrane, Mh. Boutaous, S. Xin, Process of selective laser sintering of polymer powders: modeling, simulation, and validation. Comptes Rendus. Mécanique 346(11), 1087–1103 (2018)10.1016/j.crme.2018.08.002 ↗
19. D. Riedlbauer, M. Drexler, D. Drummer, P. Steinmann, J. Mergheim, Modelling, simulation and experimental validation of heat transfer in selective laser melting of the polymeric material PA12. Comput. Mater. Sci. 93, 239–248 (2014)10.1016/j.commatsci.2014.06.046 ↗
20. F. Shen, W. Zhu, K. Zhou, L.-L. Ke, Modeling the temperature, crystallization, and residual stress for selective laser sintering of polymeric powder. Acta Mech. 232(9), 3635–3653 (2021)10.1007/s00707-021-03020-6 ↗
21. Z. Zhang, Y. Huang, A.R. Kasinathan, S.I. Shahabad, U. Ali, Y. Mahmoodkhani, E. Toyserkani, 3-dimensional heat transfer modeling for laser powder-bed fusion additive manufacturing with volumetric heat sources based on varied thermal conductivity and absorptivity. Opt. Laser Technol. (2019). https://doi.org/10.1016/j.optlastec.2018.08.01210.1016/j.optlastec.2018.08.012 ↗
22. O. Eren, 3D multi-physics finite element simulation of the selective laser sintering process for polyamide 12: effects of laser parameters on melt pool formations and sintering quality. Macromol. Theory Simul. (2025). https://doi.org/10.1002/mats.20250009410.1002/mats.202500094 ↗
23. P. Peyre, Y. Rouchausse, D. Defauchy, G. Régnier, Experimental and numerical analysis of the selective laser sintering (SLS) of PA12 and PEKK semi-crystalline polymers. J. Mater. Process. Technol., 2015;225326–22533610.1016/j.jmatprotec.2015.04.030 ↗
24. A. Gobal, B. Ravani, Physical modeling for selective laser sintering process. J. Comput. Inf. Sci. Eng. 17(2), 021002 (2017)10.1115/1.4034473 ↗
25. E. Mirkoohi, D.E. Seivers, H. Garmestani, S.Y. Liang, Heat source modeling in selective laser melting. Materials. 12(13), 2052 (2019)10.3390/ma12132052 ↗
26. J.C. Nelson, Selective Laser Sintering: a Definition of the Process and an Empirical Sintering Model (The University of Texas at Austin, 1993)
27. L. Xin, M. Boutaous, S. Xin, D.A. Siginer, Numerical modeling of the heating phase of the selective laser sintering process. Int. J. Therm. Sci. 120, 50–62 (2017)10.1016/j.ijthermalsci.2017.05.017 ↗
28. A. Korycki, C. Garnier, N. Rodier, F. Chabert, E. Laurent, and Nassiet V. Numerical and experimental analysis of the thermal profile of printed layers during selective laser sintering process of poly (etheretherketone). in AIP Conference Proceedings. 2019. AIP Publishing LLC10.1063/1.5112681 ↗
29. A. Haleem, M. Javaid, Polyether ether ketone (PEEK) and its manufacturing of customised 3D printed dentistry parts using additive manufacturing. Clin. Epidemiol. Global Health. 7(4), 654–660 (2019)10.1016/j.cegh.2019.03.001 ↗
30. P. Patel, T.R. Hull, R.E. Lyon, S.I. Stoliarov, R.N. Walters, S. Crowley, N. Safronava, Investigation of the thermal decomposition and flammability of PEEK and its carbon and glass-fibre composites. Polym. Degrad. Stab. 96(1), 12–22 (2011)10.1016/j.polymdegradstab.2010.11.009 ↗
31. R.D. Maksimov, J. Kubat, Time and temperature dependent deformation of poly (ether ether ketone)(PEEK). Mech. Compos. Mater. 33(6), 517–525 (1997)10.1007/BF02269611 ↗
32. J.D.D. Melo, D.W. Radford, Time and temperature dependence of the viscoelastic properties of PEEK/IM7. J. Compos. Mater. 38(20), 1815–1830 (2004)10.1177/0021998304044770 ↗
33. M. Lei, C.M. Hamel, K. Chen, Z. Zhao, H. Lu, K. Yu, H.J. Qi, Thermomechanical behaviors of polyether ether ketone (PEEK) with stretch-induced anisotropy. J. Mech. Phys. Solids 148, 104271 (2021)10.1016/j.jmps.2020.104271 ↗
34. Netzsch, PEEK: Polyetheretherketone. High-Temperature Resistant Thermoplastics 2025 [cited 2025; Available from: https://analyzing-testing.netzsch.com/en-US/polymers-netzsch-com/high-temperature-resistant-thermoplastics/peek-polyetheretherketone
35. Xometry, PEEK (PolyEtherEtherKetone) Datasheet. 2025 [cited 2025; Available from: https://xometry.eu/wp-content/uploads/2020/09/datasheet-PEEK.pdf
36. M. Madžarević, Đ Medarević, S. Pavlović, B. Ivković, J. Đuriš, S. Ibrić, Understanding the effect of energy density and formulation factors on the printability and characteristics of SLS Irbesartan tablets—application of the decision tree model. Pharmaceutics 13(11), 1969 (2021)10.3390/pharmaceutics13111969 ↗
37. T. Czelusniak, F.L. Amorim, Influence of energy density on polyamide 12 processed by SLS: from physical and mechanical properties to microstructural and crystallization evolution. Rapid Prototyp. J. 27(6), 1189–1205 (2021)10.1108/RPJ-02-2020-0027 ↗
38. A. Nazarov, I. Skornyakov, I. Shishkovsky, Design of the SLS-machine for PEEK. Nano Tech. Appl. 1(1), 1–9 (2018)10.33425/2639-9466.1006 ↗
39. F. Lupone, E. Padovano, F. Casamento, C. Badini, Process phenomena and material properties in selective laser sintering of polymers: a review. Materials 15(1), 183 (2021)10.3390/ma15010183 ↗
40. J.-B. Forien, N.P. Calta, P.J. DePond, G.M. Guss, T.T. Roehling, M.J. Matthews, Detecting keyhole pore defects and monitoring process signatures during laser powder bed fusion: a correlation between in situ pyrometry and ex situ X-ray radiography. Addit. Manuf. 35, 101336 (2020)
41. C.-Y. Liaw, J.W. Tolbert, L.W. Chow, M. Guvendiren, Interlayer bonding strength of 3D printed PEEK specimens. Soft Matter. 17(18), 4775–4789 (2021)10.1039/D1SM00417D ↗
42. D.K. Patel, A.H. Sakhaei, M. Layani, B. Zhang, Q. Ge, S. Magdassi, Highly stretchable and UV curable elastomers for digital light processing based 3D printing. Adv. Mater. 29(15), 1606000 (2017)10.1002/adma.201606000 ↗