journal article·2019-03-12Open access

MAG Welding Tests of Modern High Strength Steels with Minimum Yield Strength of 700 MPa

Teemu Lahtinen, Pedro Vilaça, Pasi Peura, Saara Mehtonen

Applied Sciences· Volume 9· Issue 5

Abstract

The modern high strength steel plates have an excellent combination of strength and toughness based on micro-alloying and complex microstructure. Retaining this combination of properties in the weld zone is a major challenge for applications in high-demanding structural construction. This work investigates the weldability of three different modern high strength steel plates, with a thickness of 8 mm. Two of the test materials were produced by a thermo-mechanically controlled process (TMCP) and one by a quenching and tempering method (Q&T). Two-passes MAG (metal active gas) welding was used with four different heat inputs. The tests implemented on all the materials included tensile, hardness profiles (HV5), Charpy-V impact toughness tests, and microstructure analysis using scanning electron microscope (SEM). For one of the TMCP steels, some extended tests were conducted to define how the tensile properties change along the weld line. These tests included tensile tests with digital image correlation (DIC), and 3-point bending tests. The most notable differences in mechanical properties of the welds between the materials were observed in Charpy-V impact toughness tests, mostly at the vicinity of the fusion line, with the Q&T steel more prone to embrittlement of the heat affected zone (HAZ) than the TMCP steels. Microstructural analysis revealed carbide concentration combined with coarse bainitic structures in HAZ of Q&T steel, explaining the more severe embrittlement. During the tensile tests, the DIC measurements have shown a strain localization in the softest region of the HAZ. Increasing the heat input resulted in earlier localization of the strain and less maximum strength. The tensile properties along the weld line were investigated in all welding conditions, and the results emphasize relevant and systematic differences of the yield strength at the transient zones near the start and end of the weld compared with the intermediate stationary domain.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Welding Techniques and Residual Stresses · Microstructure and Mechanical Properties of Steels · Hydrogen embrittlement and corrosion behaviors in metals

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Mechanical Engineering, Aalto University, 02150 Espoo, Finland

Materials Science and Environmental Engineering, Tampere University, P.O. Box 589, FI-33014 Tampere, Finland

SSAB, Rautaruukintie 155, P.O. Box 93, FI-92101 Raahe, Finland

References (34)

Show source-provided references
1. Takahashi, M. (2003). Development of High Strength Steels for Automobile, Nippon Steel and Sumitomo Metal. Nippon Steel Technical Report.
2. Matsuoka, S., Hasegawa, K., and Tanaka, Y. (2007). Newly-Developed Ultra-High Tensile Strength Steels with Excellent Formability and Weldability, JFE Steel Corporation. No. 10.
3. Effect of microstructure on mechanical properties in weld-repaired high strength low alloy steel10.1016/j.matdes.2011.11.016 ↗
4. A study of the softening mechanisms of laser-welded DP1000 steel butt joints10.1016/j.matdes.2016.02.071 ↗
5. Cleavage initiation in the intercritically reheated coarse-grained heat-affected zone: Part I. Fractographic evidence10.1007/BF02651598 ↗
6. The Influence of Niobium Microalloying on Austenite Grain Coarsening Behavior of Ti-modified SAE 8620 Steel10.2355/isijinternational.47.307 ↗
7. A first report on diagrams for grain growth in welds10.1016/0001-6160(82)90100-6 ↗
8. Improving weldability of an advanced high strength steel by design ofbase metal microstructure10.1016/j.jmatprotec.2015.09.026 ↗
9. Farrokhi, F., Siltanen, J., and Salminen, A. (2015). Fiber Laser Welding of Direct-Quenched Ultrahigh Strength Steels: Evaluation of Hardness, Tensile Strength, and Toughness Properties at Subzero Temperatures. J. Manuf. Sci. Eng., 137.10.1115/1.4030177 ↗
10. Effects of activating flux on the welded joint characteristics in gas metal arc welding10.1016/j.matdes.2009.11.043 ↗
11. Hardness Microstruct.Gradients Heat Affect. Zone Welded Low-Carbon Quenched Tempered Steels
12. A Study Concerning Intercritical HAZ Microstructure and Toughness in HSLA Steels
13. Górka, J. (2018). Assessment of Steel Subjected to the Thermomechanical Control Process with Respect to Weldability. Metals, 8.10.3390/met8030169 ↗
14. Effect of processing temperatures on the properties of a high-strength steel welded by FSW10.1007/s40194-018-0612-8 ↗
15. Microstructure and fatigue properties of friction stir welded high-strength steel plates10.1080/13621718.2017.1399574 ↗
16. Górka, J., and Stano, S. (2018). Microstructure and Properties of Hybrid Laser Arc Welded Joints (Laser Beam-MAG) in Thermo-Mechanical Control Processed S700MC Steel. Metals, 8.10.3390/met8020132 ↗
17. Effect of cooling rate on intercritically reheated microstructure and toughness in high strength low alloy steel10.1179/mst.1993.9.1.8 ↗
18. Zhang, X., and Gao, H. (2011). A study of impact toughness of intercritically reheated coarse-grain heat affected zone of two type X80 grade pipeline steel. Trans. JWRI, 101–104.
19. High toughness in the intercritically reheated coarse-grained (ICRCG) heat-affected zone (HAZ) of low carbon microalloyed steel10.1016/j.msea.2013.10.062 ↗
20. Effects of acicular ferrite on charpy impact properties in heat affected zones of oxide-containing API X80 linepipe steels10.1016/j.msea.2011.01.031 ↗
21. Optimizing the Boron Effect10.1007/BF02669367 ↗
22. (2013). SFS-EN 10149-1, Hot Rolled Flat Products Made of High Yield Strength Steels for Cold Forming. Part 1: General Technical Delivery Conditions, Suomen, Standardoimisliitto (SFS).
23. A guide to the selection and welding of low alloy structural steels
24. (2009). EN 10025-6:2004+A1, Hot Rolled Products of Structural Steels. Part 6: Technical Delivery Conditions for Flat Products of High Yield Strength Structural Steels in the Quenched and Tempered Condition, Suomen, Standardoimisliitto (SFS).
25. Ruukki Corporation (2019, February 18). Welding General. Ruukki Metals Oy. Available online: https://www.oxycoupage.com/FichiersPDF/Ruukki_Pdf/English/Ruukki-Hot-rolled-steels-Processing-of-material-Welding.pdf.
26. (2012). SFS-EN ISO 4136, Destructive Tests on Welds in Metallic Materials. Transverse Tensile Tests, Suomen, Standardoimisliitto (SFS).
27. Wallin, K. (2011). Fracture Toughness of Engineering Materials-Estimation and Application, EMAS Publishing.
28. (2016). SFS-EN ISO 148-1, Metallic Materials. Charpy Pendulum Impact Test. Part 1: Test Method, Suomen, Standardoimisliitto (SFS).
29. (2016, November 07). Australian Welding Institite. Available online: http://www.austwelding.com.au/consumables/cigweld-filler-metals-pocketguide-2008/.
30. Det Norske Veritas (2011). Rules for Classification of Ships/High Speed, Light Craft and Naval Surface Craft. Newbuildings Materials and Welding DNV, Metallic Materials, Det Norske Veritas. Part 2, Chapter 2.
31. Winczek, J. (2017). Modeling of Temperature Field during Multi-Pass GMAW Surfacing or Rebuilding of Steel Elements Taking into Account the Heat of the Deposit Metal. Appl. Sci., 7.10.3390/app7010006 ↗
32. The Influence of Temperature on Mechanical Properties of the Base Material and Welded Joint Made of Steel S690QL
33. Crack initiation mechanisms and threshold values of very high cycle fatigue failure of high strength steels10.1016/j.proeng.2014.06.229 ↗
34. Influence of carbides on the high-temperature tempered martensite embrittlement of martensitic heat-resistant steels10.1016/j.msea.2016.06.025 ↗