journal article·2020-02-20Open access

A Hybrid Tolerance Design Method for the Active Phased-Array Antenna

Guodong Sa, Zhenyu Liu, Chan Qiu, Jianrong Tan

Applied Sciences· Volume 10· Issue 4

Abstract

With the increase of the working frequency of the array antenna, tolerance design has become increasingly important. The state-of-art tolerance design methods mainly deal with the position tolerance of the discrete elements. However, the geometric errors of the whole array have resulted from two aspects: (1) the position errors of the discrete elements and (2) the form errors of the continuous reflection plate. To optimize the position tolerance and flatness simultaneously, a hybrid tolerance design method is proposed. First, the relation between the performance of the array antenna and hybrid tolerances was determined based on the second order Taylor expansion. Then the expectation and variance of the performance were derived. Finally, the hybrid tolerances were optimized and the performance of the antenna was improved. Simulation results proved the effectiveness and efficiency of the proposed hybrid tolerance design method.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Antenna Design and Optimization · Structural Analysis and Optimization · Advanced Antenna and Metasurface Technologies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

State Key Laboratory of CAD&CG, Zhejiang University, Hangzhou 310000, China

Ningbo Research Institute, Ningbo 31500, China

Funding

National Natural Science Foundation of China

References (23)

Show source-provided references
1. Mechanical and Electrical Tolerances for Two-Dimensional Scanning Antenna Arrays10.1109/TAP.1958.1144549 ↗
2. Performance of phased-array antennas with mechanical errors10.1109/7.144579 ↗
3. So, K.K., Luk, K.M., Chan, C.H., and Chan, K.F. (2018). 3D Printed High Gain Complementary Dipole/Slot Antenna Array. Appl. Sci., 8.10.3390/app8081410 ↗
4. Lee, H., Kim, S., and Choi, J. (2019). A 28 GHz 5G Phased Array Antenna with Air-Hole Slots for Beam Width Enhancement. Appl. Sci., 9.10.3390/app9204204 ↗
5. Position Tolerance Design Method for Array Antenna in Internet of Things
6. The Effect of Aperture Errors on the Antenna Radiation Pattern10.1007/BF02903409 ↗
7. Influence of correlation interval and illumination taper in antenna tolerance theory10.1049/piee.1969.0042 ↗
8. An efficient computational method for characterizing the effects of random surface errors on the average power pattern of reflectors10.1109/TAP.1983.1142978 ↗
9. Computation of the Average Power Pattern of a Reflector Antenna with Random Surface Errors and Misalignment Errors10.1109/8.504307 ↗
10. Decision of error tolerance in array element by the Monte Carlo method10.1109/TAP.2005.844444 ↗
11. Electromechanical coupling based performance evaluation of distorted phased array antennas with random position errors10.3233/JAE-150170 ↗
12. On the effects of calibration errors and mutual coupling on the beam pattern of an antenna array10.1109/TAP.2013.2259455 ↗
13. Tolerance analysis of antenna arrays through interval arithmetic10.1109/TAP.2013.2276927 ↗
14. Anselmi, N., Salucci, M., Rocca, P., and Massa, A. (2016). Power pattern sensitivity to calibration errors and mutual coupling in linear arrays through circular interval arithmetics. Sensors, 16.10.3390/s16060791 ↗
15. Guo, F., Liu, Z., Sa, G., and Tan, J. (2019). A Position Error Representation Method for Planar Arrays. IEEE Antennas Wirel. Propag. Lett., 1.10.1109/LAWP.2019.2954954 ↗
16. A Novel Region-Division-Based Tolerance Design Method for a Large Number of Discrete Elements Distributed on a Large Surface10.1115/1.4041573 ↗
17. Analysis of performance of active phased array antennas with distorted plane error10.1080/00207210902738067 ↗
18. Sa, G., Liu, Z., Qiu, C., Peng, X., and Tan, J. (2019). A Tolerance Analysis Method Considering Form Defects Based on Variance Separation. Proc. Inst. Mech. Eng. B J. Eng. Manuf., in press.
19. Winkler, D.F., and Webster, J.L. (1997). Searching the Skies: The Legacy of the United States Cold War Defense Radar Program (No. SR-97-78), Construction Engineering Research Lab (Army).
20. Analytical method for optimal component tolerances based on manufacturing cost and quality loss10.1177/0954405413488769 ↗
21. He, C., Zhang, S., Qiu, L., Liu, X., and Wang, Z. (2019). Assembly Tolerance Design Based on Skin Model Shapes Considering Processing Feature Degradation. Appl. Sci., 9.10.3390/app9163216 ↗
22. Mailloux, R.J. (2005). Phased Array Antenna Handbook, Artech House. [2nd ed.].
23. Kraus John, D., and Marhefka Ronald, J. (2008). Antennas: For all Applications, Mc Graw Hill. [3rd ed.].