journal article·2017-11-14Open access

Structural Performance Optimization and Verification of an Improved Thin-Walled Storage Tank for a Pico-Satellite

Lai Teng, Zhonghe Jin

Applied Sciences· Volume 7· Issue 11

Abstract

This paper presents an improved mesh storage tank structure obtained using 3D metal printing. The storage tank structure is optimized using a multi-objective uniform design method. Each parameter influencing the storage tank is considered as the optimization factor, and the compression stress ( σ ), volume utilization ratio ( v ), and weight ( m , are considered as the optimization objectives. Regression equations were established between the optimization factors and targets, the orders of the six factors affecting three target values are analyzed, and the relative deviations between the regression equation and calculation results for σ , v , and m were 9.72%, 4.15%, and 2.94%, respectively. The optimization results showed that the regression equations can predict the structure performance of the improved storage tank, and the values of the influence factors obtained through the optimization are effective. In addition, the compression stress was improved by 24.98%, the volume utilization ratio was increased by 26.86%, and the weight was reduced by 26.83%. The optimized storage tank was developed through 3D metal printing, and the compressive stress was improved by 58.71%, the volume utilization ratio was increased by 24.52%, and the weight was reduced by 11.67%.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Spacecraft and Cryogenic Technologies · Spacecraft Design and Technology · Rocket and propulsion systems research

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

School of Aeronautics and Astronautics, Zhejiang University, Hangzhou 310027, China

Funding

The Fundamental Research Funds for the Central Universities · China National Funds for Distinguished Young Scientists

References (43)

Show source-provided references
1. Numerical modeling and optimization of thermal stratification in solar hot water storage tanks for domestic applications: CFD study10.1016/j.solener.2017.08.061 ↗
2. Performance evaluation and optimization of encapsulated cascade PCM thermal storage10.1016/j.est.2017.02.003 ↗
3. Buckling of vertical oil storage steel tanks: Review of static buckling studies10.1016/j.tws.2016.01.026 ↗
4. Research on the Vibration Characteristics of Vertical Cylindrical Shell Container
5. Buckling of fixed-roof aboveground oil storage tanks under heat induced by an external fire10.1016/j.tws.2011.12.005 ↗
6. The effects of long-term corrosion on the dynamic characteristics of ground based cylindrical liquid storage tanks10.1016/j.tws.2010.05.003 ↗
7. Free vibrations of composite tanks partially filled with fluid10.1016/j.tws.2009.05.007 ↗
8. Optimizing design of a new zero boil off cryogenic storage tank in microgravity10.1016/j.apenergy.2015.01.104 ↗
9. Optimizing design of a new ZBO cryogenic storage tank in microgravity10.1016/j.egypro.2014.12.248 ↗
10. Buckling of bi-segment spherical shells under hydrostatic external pressure10.1016/j.tws.2017.08.017 ↗
11. Buckling of cylindrical steel tanks with oblique body imperfection under uniform external pressure10.1115/1.4037808 ↗
12. Stability of open top cylindrical steel storage tanks: Design of top wind girder10.1115/1.4035507 ↗
13. Performance criteria for liquid storage tanks and piping systems subjected to seismic loading10.1115/1.4036916 ↗
14. Simplified procedure for design of liquid-storage combined conical tanks10.1016/j.tws.2008.12.005 ↗
15. Capacity of liquid-filled steel conical tanks under vertical excitation10.1016/j.tws.2016.02.012 ↗
16. Sensitivity analysis for thermocline thermal storage tank design10.1016/j.renene.2016.07.052 ↗
17. Improved thermal stratification with obstacles placed inside the vertical mantled hot water tanks10.1016/j.applthermaleng.2016.01.069 ↗
18. A coupled finite element genetic algorithm for optimum design of stiffened liquid-filled steel conical tanks10.1016/j.tws.2010.12.006 ↗
19. On the rational design of the top wind girder of large storage tanks10.1016/j.tws.2015.10.014 ↗
20. Heuristic optimization of cylindrical thin-walled steel tanks under seismic loads10.1016/j.tws.2012.12.009 ↗
21. Thermal stratification in a hot water tank established by heat loss from the tank10.1016/j.solener.2012.07.026 ↗
22. Experimental investigation on the effect of geometric imperfections on the buckling and post-buckling behavior of steel tanks under hydrostatic pressure10.1016/j.tws.2013.09.005 ↗
23. Micro-propulsion System for Modern Small Satellites
24. Satellite thruster configuration design based on propellant consumption optimization
25. Application of electric propulsion on communications satellite platform
26. Li, H. (2015). Study on Preparation and Properties of Micro Thruster. [Master’s Thesis, Anhui Polytechnic University].
27. Yang, K.J. (2015). Stress Analysis of Pressure Vessel with Elliptical Cross Section. [Master’s Thesis, Xi’an Shiyou University].
28. Optimal design of pressure vessel using an improved genetic algorithm10.1631/jzus.A0820217 ↗
29. 6 U Cubesat commercial applications10.1017/S0001924000006692 ↗
30. Wang, Z. (2015). Structural Optimization Design of Micro Thruster Based on Piezoelectric Transformer. [Master’s Thesis, Anhui Polytechnic University].
31. Xu, W.P. (2016). Structure Optimization in 3D Printers. [Ph.D. Thesis, University of Science and Technology of China].
32. Research status and key technologies of 3D printing
33. Salmi, L.M. (2013). Medical Applications of Additive Manufacturing in Surgery and Dental Care. [Ph.D. Thesis, Aalto University].
34. A study of the micro-structural evolution during selective laser melting of Ti-6Al-4V10.1016/j.actamat.2010.02.004 ↗
35. Research progress of 3D printing metal materials
36. Application and prospect of 3D printing in metal forming
37. Li, Y. (2015). Study on the Process and Properties of Porous Metal Prepared by Laser Additive Manufacturing (3D Printing). [Master’s Thesis, Soochow University].
38. The ultrasonic burnishing of cobalt-chrome and stainless steel surface made by additive manufacturing10.1007/s40964-017-0017-z ↗
39. Jiang, J.J. (2015). Study on the Microstructure and Properties of Biomedical Ti-6Al-4V Produced by Selective Laser Melting. [Ph.D. Thesis, Chongqing University].
40. Study on biological corrosion and biocompatibility of TC4 alloy by Selective Laser Melting
41. Technology of ammonia flashing jet propulsion in BX-1 satellite
42. A step by step method for optimizing satellite structure
43. Cheng, L. (2016). Design and Optimization of a Mass Production Satellite Structure. [Master’s Thesis, University of Chinese Academy of Sciences].