journal article·2023-11-23Open access

Characterizing the Vibration Responses of Flexible Workpieces during the Turning Process for Quality Control

Chun Li, Zhexiang Zou, Wenbo Duan, Jiajie Liu, Fengshou Gu, Andrew David Ball

Applied Sciences· Volume 13· Issue 23

Abstract

The chatter that occurs during the turning operation, especially when cutting a slender and flexible shaft, determines the surface quality of the workpiece and the stability of the machining system. However, when building a dynamic model of a slender workpiece with a chuck and tailstock, it is generally regarded as a cantilever or simply supported beam, without consideration of the axial force and supported stiffness effect. In this work, a dynamic model for thin and flexible workpieces with different clamping boundary conditions was first built. Then, a finite element analysis (FEA) was used to study the influence of the axial force and supporting stiffness on the mode frequencies of the workpiece. A further analysis found that the relationship between support stiffness, axial force, and the dynamic response of the workpiece is nonlinear and far more complex than that of the simply supported beam model. The clamping force directly influenced the magnitude of the vibration response with the decrease of shaft stiffness during the turning process. These results were verified experimentally by measuring the vibrational response of slender shafts with different clamping modes using an on-rotor sensing (ORS) system. It proved that the proposed model shows advantages for the identification of dynamic vibration and quality control when machining slender workpieces.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Advanced machining processes and optimization · Advanced Surface Polishing Techniques · Advanced Machining and Optimization Techniques

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

School of Industrial Automation, Beijing Institute of Technology, Zhuhai 519088, China

Centre for Efficiency and Performance Engineering, University of Huddersfield, Huddersfield HD1 3DH, UK

Institute of Engineering and Technology, University of Hertfordshire, Hatfield, Hertfordshire AL10 9AB, UK

Funding

2023 Guangdong Province Science and Technology Innovation Strategy (Climbing Plan Project) Special Fund · Guangdong Basic and Applied Basic Research Fund Offshore Wind Power Scheme-General Project · Fundamental and Foundational Applied Research Project · Special Projects in Key Areas in Fundamental and Foundational Applied Research of Guangdong Provincial Education Department

References (35)

Show source-provided references
1. Stability Analysis of Turning Process with Tailstock-Supported Workpiece10.1007/s00170-008-1764-2 ↗
2. Study on Surface Quality and Subsurface Damage Mechanism of Nickel-Based Single-Crystal Superalloy in Precision Turning10.1016/j.jmapro.2023.05.053 ↗
3. Chatter Avoidance in Cutting Highly Flexible Workpieces10.1016/j.cirp.2017.04.054 ↗
4. Development of Constrained Layer Damping Toolholder to Improve Chatter Stability in End Milling10.1016/j.ijmecsci.2016.09.003 ↗
5. A Stability Analysis of Turning a Tailstock Supported Flexible Work-Piece10.1016/j.ijmachtools.2005.04.002 ↗
6. Analysis and Implementation of Chatter Frequency Dependent Constrained Layer Damping Tool Holder for Stability Improvement in Turning Process
7. Nonlinear Dynamic Analysis of Flexible Workpiece and Tool in Turning Operation with Delay and Internal Resonance10.1016/j.jsv.2018.05.043 ↗
8. Model-Based Chatter Stability Prediction and Detection for the Turning of a Flexible Workpiece10.1016/j.ymssp.2017.08.022 ↗
9. Parallel Turning Process Parameter Optimization Based on a Novel Heuristic Approach10.1115/1.2823077 ↗
10. Dynamic Analysis of Continuous Beams by the Boundary Element Method10.1016/j.enganabound.2019.03.015 ↗
11. Modelling the Dynamics of a Large Damped Boring Bar in a Lathe10.1016/j.procir.2019.04.041 ↗
12. Machining of Slender Workpieces Subjected to Time-Periodic Axial Force: Stability and Chatter Suppression10.1016/j.jsv.2021.116114 ↗
13. Yekdane, A., Movahedian, B., and Boroomand, B. (2020). An Efficient Time-Space Formulation for Dynamic Transient Analyses: Application to the Beam Assemblies Subjected to Moving Loads and Masses, Elsevier Inc.10.1016/j.apm.2020.11.037 ↗
14. Tuning of Tool Dynamics for Increased Stability of Parallel (Simultaneous) Turning Processes10.1016/j.jsv.2015.09.009 ↗
15. Chatter Resistance of Non-Uniform Turning Bars with Attached Dynamic Absorbers-Analytical Approach10.1016/j.jsv.2009.12.015 ↗
16. Natural Frequencies and Mode Shapes of Deterministic and Stochastic Non-Homogeneous Rods and Beams10.1016/j.jsv.2006.12.021 ↗
17. Natural Frequencies and Mode Shapes for Axisymmetric Vibrations of Shells in Turning-Point Range10.1016/j.ijsolstr.2005.06.082 ↗
18. Dynamics Identification and Stability Analysis in Turning of Slender Workpieces with Flexible Boundary Constraints10.1016/j.ymssp.2022.109245 ↗
19. Selection of Lathe Spindle Material Based on Static and Dynamic Analyses Using Finite Element Method10.1016/j.matpr.2020.02.182 ↗
20. Finite Element Analysis of Bending Occurring While Cutting with High Speed Steel Lathe Cutting Tools10.1016/j.matdes.2004.07.028 ↗
21. Finite Element Analysis of Machine and Workpiece Instability in Turning10.1016/j.ijmachtools.2004.11.017 ↗
22. Finite Element Dynamic Analysis of Finite Beams on a Bilinear Foundation under a Moving Load10.1016/j.jsv.2014.12.044 ↗
23. Dynamic Analysis of Euler-Bernoulli Beam Problems Using the Generalized Finite Element Method10.1016/j.compstruc.2016.05.019 ↗
24. Virtual Experimental Modal Analysis of a Cantilever Beam
25. A United Model of Diametral Error in Slender Bar Turning with a Follower Rest10.1016/j.ijmachtools.2005.07.042 ↗
26. Li, C., Li, B., Gu, L., Feng, G., Gu, F., and Ball, A.D. (2020, January 4–6). Online Monitoring of a Shaft Turning Process Based on Vibration Signals from On-Rotor Sensor. Proceedings of the 2020 3rd World Conference on Mechanical Engineering and Intelligent Manufacturing (WCMENIM), Shanghai, China.10.1109/WCMEIM52463.2020.00091 ↗
27. Characterising the Behaviour of Workpieces under the Effect of Tangential Cutting Force during NC Turning: Application to Machining of Slender Workpieces10.1016/j.jmatprotec.2005.08.015 ↗
28. An Ultimate-State-Based-Model for Inelastic Analysis of Intermediate Slenderness PSB Columns under Eccentrically Compressive Load10.1016/j.conbuildmat.2015.06.059 ↗
29. Analysis of the Cutting Ratio and Investigating Its Influence on the Workpiece’s Diametrical Error in Ultrasonic-Vibration Assisted Turning10.1177/0954405420968174 ↗
30. Vibration Monitoring of Turning a Shaft on a Lathe Based on Signals from an On-Rotor Sensor10.1007/978-3-030-75793-9_84 ↗
31. Rao, S.S. (2006). Vibration of Continuous Systems, Wiley.10.1002/9780470117866 ↗
32. Transverse Vibrations of Cantilever Beams: Analytical Solutions with General Steady-State Forcing
33. Assessment of a Three-Axis on-Rotor Sensing Performance for Machining Process Monitoring: A Case Study10.1038/s41598-022-21415-w ↗
34. Li, C., Li, B., Wang, H., Shi, D., Gu, F., and Ball, A.D. (2022). International Conference on the Efficiency and Performance Engineering Network, Springer Nature.
35. Design Optimization for Minimum Technological Parameters When Dry Turning of AISI D3 Steel Using Taguchi Method10.1007/s00170-016-9162-7 ↗