journal article·2022-11-16Open access

Multi-Objective Optimization of an Axial Flux Permanent Magnet Brushless DC Motor with Arc-Shaped Magnets

Shasha Wu, Hao Xu, Tao Zhang, Quanhao Gu, Baojian Wang

Applied Sciences· Volume 12· Issue 22

Abstract

To get a better electromagnetic performance of an axial flux permanent magnet brushless DC motor (AFPMBLDC), an AFPMBLDC with arc-shaped magnets and its multi-objective optimization design are researched. Firstly, the main design parameters of the AFPMBLDC are proposed, and the initial designs are carried out according to the given requirements. Furthermore, the pole arc coefficient, permanent magnet thickness, permanent magnet arc radius, and air-gap length are selected as optimization factors. Then, an orthogonal experiment table is established, in which the flux density, no-load back EMF, harmonic distortion rate, and output torque ripple are selected as optimization targets. The Taguchi optimization method is adopted to optimize the performance indexes and the optimal parameters are obtained. Finally, the optimized model is constructed, and some simulations are carried out to verify the optimal design. The research results have shown that the air-gap flux density of the optimized AFPMBLDC is reduced to 31.8%, the total harmonic distortion rate of no-load back EMF is less than 7.5%, and the torque ripple is reduced to 4.3%.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Electric Motor Design and Analysis · Induction Heating and Inverter Technology · Sensorless Control of Electric Motors

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Faculty of Automation, Huaiyin Institute of Technology, Huaian 223003, China

References (40)

Show source-provided references
1. Seo, J.M., Rhyu, S.H., Kim, J.H., Choi, J.H., and Jung, I.S. (2010, January 21–24). Design of axial flux permanent magnet brushless DC motor for robot joint module. Proceedings of the 2010 International Power Electronics Conference—ECCE ASIA, Sapporo, Japan.10.1109/IPEC.2010.5544557 ↗
2. Yin, H., Yu, Y., and Li, J. (2017, January 18–20). Optimization design of a motor embedded in a light weight robotic joint. Proceedings of the 12th IEEE Conference on Industrial Electronics and Applications (ICIEA), Siem Reap, Cambodia.10.1109/ICIEA.2017.8283100 ↗
3. Saha, B., and Singh, B. (2022, January 15–17). An Improved Flux Observer Based Position Sensorless Single Stage BLDC Motor Drive with Regenerative Braking for Solar Powered LEV. Proceedings of the 2022 IEEE Transportation Electrification Conference & Expo (ITEC), Anaheim, CA, USA.10.1109/ITEC53557.2022.9813794 ↗
4. Intelligent Fault Diagnosis for BLDC with Incorporating Accuracy and False Negative Rate in Feature Selection Optimization10.1109/ACCESS.2022.3186753 ↗
5. Cao, X., Li, G., Ye, Q., Zhou, R., Ma, G., and Zhou, F. (2017, January 18–20). Multi-objective optimization of permanent magnet synchronous motor based on elite retention hybrid simulated annealing algorithm. Proceedings of the 12th IEEE Conference on Industrial Electronics and Applications (ICIEA), Siem Reap, Cambodia.10.1109/ICIEA.2017.8282902 ↗
6. Genetic algorithm and particle swarm optimization tuned fuzzy PID controller on direct torque control of dual star induction motor10.1007/s11771-019-4142-3 ↗
7. Multiobjective and multiphysics design optimization of a switched reluctance motor for electric vehicle applications10.1109/TEC.2021.3078547 ↗
8. Analysis and Calculation of Top Leakage of Surface-mounted Axial Flux Permanent Magnet Motor
9. Diao, K., Bramerdorfer, G., Sun, X., Yang, Z., and Han, S. (2022). Multi-objective Design Optimization of a Novel Switched Reluctance Motor with Unequal Alternating Stator Yoke Segments. IEEE Trans. Transp. Electr.10.1109/TTE.2022.3174337 ↗
10. Comprehensive sensitivity and cross-factor variance analysis-based multi-objective design optimization of a 3-DOF hybrid magnetic bearing10.1109/TMAG.2020.3005446 ↗
11. Multi-Objective Design Optimization of an IPMSM Based on Multilevel Strategy10.1109/TIE.2020.2965463 ↗
12. Robust Multi-Objective Optimization of a 3-Pole Active Magnetic Bearing Based on Combined Curves with Climbing Algorithm10.1109/TIE.2021.3088380 ↗
13. Multi-objective Optimal Design of Bearingless Permanent Magnet Synchronous Motor Based on Improved Particle Swarm Optimization
14. Sun, X., Xu, N., and Yao, M. (2022). Sequential subspace optimization design of a dual three-phase permanent magnet synchronous hub motor based on NSGA III. IEEE Trans. Transp. Electrific.10.1109/TTE.2022.3190536 ↗
15. Particle swarm optimization based fuzzy controller for permanent magnet synchronous motor control. Control
16. Multiobjective optimization of a five-phase bearingless permanent magnet motor considering winding area10.1109/TMECH.2021.3121802 ↗
17. Srivastava, A., Das, D.K., Rai, A., and Raj, R. (2018). Parameter estimation of a permanent magnet synchronous motor using whale optimization algorithm. Adv. Eng. Technol. Computat. Sci. (RAETCS), 1–6.10.1109/RAETCS.2018.8443839 ↗
18. Robust-oriented optimization of switched reluctance motors considering manufacturing fluctuation10.1109/TTE.2021.3137385 ↗
19. Research on torque ripple and structural optimization of switched reluctance motors
20. Multi-objective optimal design of high-speed surface-mounted permanent magnet synchronous motor for magnetically levitated flywheel energy storage system
21. Parameter optimization of adaptive flux-weakening strategy for permanent-magnet synchronous motor drives based on particle swarm algorithm10.1109/TPEL.2019.2908380 ↗
22. Optimization of linear vibration generator design based on particle swarm algorithm
23. A new optimal design of surface mounted permanent magnet synchronous motors with integral slot per pole
24. Wen, Z., Xiong, B., and Gu, G. (2019, January 11–14). Optimization design of low speed axial flux Halbach permanent-magnet generator with PCB winding. Proceedings of the 22nd International Conference on Electrical Machines and Systems (ICEMS), Harbin, China.10.1109/ICEMS.2019.8922544 ↗
25. Yang, L., Ho, S.L., and Fu, W. (2015, January 11–15). Design optimization of a permanent magnet motor with a modified Halbach magnetization. Proceedings of the IEEE International Magnetics Conference (INTERMAG), Beijing, China.10.1109/INTMAG.2015.7157803 ↗
26. Optimization of halbach permanent magnet motor based on multi-objective sensitivity10.30941/CESTEMS.2020.00004 ↗
27. Multi-objective system level optimization method for switched reluctance motor drive systems using finite-element model10.1109/TIE.2019.2962483 ↗
28. Optimization of spiral windings for PCB disk-type permanent magnet synchronous motors
29. Analytical calculation of air-gap leakage and no-load air-gap magnetic density of disk motors
30. Adaptive flux-weakening controller for interior permanent magnet synchronous motor drives10.1109/JESTPE.2014.2299153 ↗
31. A fuzzy-based taguchi method for multiobjective design of PM motors10.1109/TMAG.2013.2242854 ↗
32. Robust design optimization of switched reluctance motor drive systems based on system-level sequential Taguchi method10.1109/TEC.2021.3085668 ↗
33. Multiobjective Design optimization of an IPMSM for EVs based on fuzzy method and sequential Taguchi method10.1109/TIE.2020.3031534 ↗
34. Robust Design optimization of a five-phase PM hub motor for fault-tolerant operation based on Taguchi method10.1109/TEC.2020.2989438 ↗
35. Multi-objective optimal design of surface-built permanent magnet synchronous motor based on Taguchi method
36. Optimal design of embedded permanent magnet motor based on Taguchi method
37. Application of Taguchi’s method to the optimization of permanent magnet synchronous motor structure
38. Optimal design of bearingless permanent magnet synchronous motor rotor based on combined poles
39. Xu, J., Gao, L., Zeng, L., and Pei, R. (2019, January 1–4). Optimum design of interior permanent magnet synchronous motor using taguchi method. Proceedings of the IEEE Transportation Electrification Conference and Expo (ITEC), Detroit, MI, USA.10.1109/ITEC.2019.8790592 ↗
40. Multi-objective optimization of surface-mounted and interior permanent magnet synchronous motor based on Taguchi method and response surface method