An Experimental Study on the Injection Characteristics and the Macroscopic Spray Characteristics of Rapeseed Oil-Diesel Fuel Blends
Source abstract
Abstract
In this study, the injection processes and spray behavior of diesel fuel (DF), rapeseed oil (RO) and their fuel blends (RO25, RO50, RO75) have been qualitatively and quantitatively analyzed to identify the differences in the injection rate and the spray parameters. The volumetric and mass injection rates, the spray penetration, the spray cone angle and the spray area under non-evaporation conditions in a nitrogen-filled camber were analyzed. The results showed that rapeseed oil leads to a decrease in the peak injection rate due to its higher density and viscosity. Moreover, rapeseed oil and its blends with mineral diesel oil exhibited smoother rising slopes at the start of injection. The spray tip penetration was the longest for the rapeseed oil and the spray tip penetrations of the fuel blends RO25, RO50 and RO75 were arranged between the values of DF and RO. As the injection pressure increased, the differences in the spray tip penetrations diminished. Increasing the amount of rapeseed oil in fuel blends resulted in a smaller spray cone angle compared to diesel fuel. The spray area of all tested fuels increased significantly with increasing spray tip penetration, the spray area of RO was consistently lower than that of diesel fuel.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Advanced Combustion Engine Technologies · Biodiesel Production and Applications · Heat transfer and supercritical fluids
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Department of Mechanical, Energy and Biotechnology Engineering, Faculty of Engineering, Agriculture Academy, Vytautas Magnus University, 53361 Kaunas, Lithuania
References (35)
Show source-provided references
1. Holden, N.M., Wolfe, M.L., Ogejo, J.A., and Cummins, E.J. (2021). Introduction to Biosystems Engineering, American Society of Agricultural and Biological Engineers (ASABE) and Virginia Technical Publishing.10.21061/intro2biosystemsengineering ↗
2. (2020). Kraftstoffe für Pflanzenöltaugliche Motoren—Rapsölkraftstoff—Anforderungen und Prüfverfahren/Fuels for Vegetable Oil Compatible Combustion Engines—Fuel from Rapeseed Oil—Requirements and Test Methods (Standard No. DIN 51605:2020-11).
3. Fridrihsone, A., Romagnoli, F., and Cabulis, U. (2020). Environmental life cycle assessment of rapeseed and rapeseed oil produced in Northern Europe: A Latvian case study. J. Sustain., 12.10.3390/su12145699 ↗
4. Economic and sustainability of biodiesel production—A systematic literature review10.3390/cleantechnol3010002 ↗
5. Lefebvre, A.H., and McDonell, V.G. (2017). Atomization and Sprays, CRC Press. [2nd ed.]. eBook.10.1201/9781315120911 ↗
6. Experimental study on injection characteristics of fatty acid esters on a diesel engine common rail system10.1016/j.fuel.2014.01.048 ↗
7. Experimental investigation of the behaviour of non-esterified rapeseed oil in a diesel engine mechanical fuel injection system10.1016/j.fuel.2012.02.055 ↗
8. Evaluation of pure rapeseed oil as a renewable fuel for agricultural machinery based on emission characteristics and long-term operation behaviour of a fleet of 18 tractors10.1007/s42452-020-03490-8 ↗
9. Aguado-Deblas, L., Hidalgo-Carrillo, J., Bautista, F.M., Luna, C., Calero, J., Posadillo, A., Romero, A.A., Luna, D., and Estévez, R. (2020). Biofuels from Diethyl Carbonate and Vegetable Oils for Use in Triple Blends with Diesel Fuel: Effect on Performance and Smoke Emissions of a Diesel Engine. Energies, 13.10.3390/en13246584 ↗
10. Atomization of high viscosity liquids through hydraulic atomizers designed for water atomization10.1016/j.expthermflusci.2017.03.004 ↗
11. Experimental investigation concerning the influence of fuel type and properties on the injection and atomization of liquid biofuels in an optical combustion chamber10.1016/j.biombioe.2013.07.004 ↗
12. Study on viscosity and surface tension properties of biodiesel-diesel blends and their effects on spray parameters for CI engines10.1016/j.fuel.2018.02.021 ↗
13. Spray, atomization and combustion characteristics of oxygenated fuels in a constant volume bomb: A review
14. An Experimental Study on the Macroscopic Spray Characteristics of Biodiesel and Diesel in a Constant Volume Chamber10.3390/en8065952 ↗
15. Effect of Fuel Physical Properties on Spray Parameters of Residual Fuel Oil (RFO)
16. Experimental study on diesel fuel injection characteristics under cold start conditions with single and split injection strategies10.1016/j.fuproc.2014.10.003 ↗
17. Using one-dimensional modeling to analyse the influence of the use of biodiesels on the dynamic behavior of solenoid-operated injectors in common rail systems: Detailed injection system model10.1016/j.enconman.2011.10.004 ↗
18. Using one-dimensional modeling to analyze the influence of the use of biodiesels on the dynamic behavior of solenoid-operated injectors in common rail systems: Results of the simulations and discussion10.1016/j.enconman.2011.10.007 ↗
19. Macroscopic spray characteristics of next-generation bio-derived diesel fuels in comparison to mineral diesel10.1016/j.apenergy.2016.10.082 ↗
20. The effect of injection pressure and fuel viscosity on the spray characteristics of biodiesel blends injected into an atmospheric chamber10.1007/s12206-012-0703-1 ↗
21. Impact of physical properties of biodiesel on the injection process in a common-rail direct injection system10.1016/j.enconman.2009.07.005 ↗
22. Influence of physical fuel properties on the injection rate in a Diesel injector10.1016/j.fuel.2011.11.073 ↗
23. Performance of direct-injection off-road diesel engine on rapeseed oil10.1016/j.renene.2005.05.009 ↗
24. Influence of viscosity, surface, and interfacial tensions on the liquid droplet collisions10.1016/j.ces.2020.115639 ↗
25. Comparative evaluation of the combustion process and emissions of a diesel engine operating on the cetane improver 2-Ethylhexyl nitrate doped rapeseed oil and aviation JP-8 fuel
26. An experimental study of gasoline effects on injection rate, momentum flux and spray characteristics using a common rail diesel injection system10.1016/j.fuel.2011.11.065 ↗
27. The influence of cavitation on the internal flow and the spray characteristics in diesel injection nozzles10.1016/j.fuel.2003.09.010 ↗
28. Measurement and prediction of speeds of sound of fatty acid ethyl esters and ethylic biodiesels10.1016/j.fuel.2013.02.041 ↗
29. Wang, Z. (2015). Experimental Study on Diesel Spray with Single and Multiple Injection under Room Temperature and Low Temperature. [Ph.D. Thesis, University of Birmingham].
30. Zeuch method-based injection rate analysis of a common-rail system operated with advanced injection strategies10.1016/j.fuel.2014.03.006 ↗
31. Analytical study for atomization of biodiesels and their blends in a typical injector: Surface tension and viscosity effects10.1016/j.fuel.2006.11.006 ↗
32. Performance and exhaust emissions of direct-injection diesel engine operating on rapeseed oil and its blends with diesel fuel10.3846/16484142.2005.9638019 ↗
33. Bosch, W. (1966). The fuel rate indicator: A new instrument for display of the characteristic of individual injection. SAE Pap., 660749.10.4271/660749 ↗
34. Performance and emissions of sunflower, rapeseed, and cottonseed oils as fuels in an agricultural tractor engine
35. Lamoot, L., Manescau, B., Chetehouna, K., and Gascoin, N. (2021). Review on the Effect of the Phenomenon of Cavitation in Combustion Efficiency, and the Role of Biofuels as a Solution against Cavitation. Energies, 14.10.3390/en14217265 ↗