journal article·2023-09-06Open access

Effectiveness of Bonding Steel Elements with Polyester-Coated Paint

Anna Rudawska, Arkadiusz Gola, Jakub Pizoń, Paweł Capała, Łukasz Wójcik

Applied Sciences· Volume 13· Issue 18

Abstract

The aim of the paper is to assess the impact of the effectiveness of bonding steel elements with paint coating. The adhesive joints were made using two types of the adhesives: two-component epoxy resin adhesive based on Bisphenol A and polyurethane. Three types of adhesive joints were made: (i) reference samples, (ii) samples with a paint polyester coating, and (iii) samples with a zinc primer and paint polyester coating. These coatings were applied using the electrokinetic method. A shear strength test of the adhesive joints (EN DIN 1465 standard), a coating adhesion test (ASTM D3359-B standard), and surface wettability tests (based on contact angle) were used. Through analyzing the test results, it can be seen that the strength of the adhesive joints of the reference samples made with epoxy adhesive is 46% lower than that of the specimens with primer and paint coating applied. However, in the case of the adhesive joints made with the polyurethane adhesive, the aforementioned difference in the strength value of the adhesive joints of the reference samples and paint-coated samples with an applied primer is 76%. Adherends with a paint coating and a previously applied primer obtained the lowest value of the contact angle (38.72°) and are characterized by good wettability.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Concrete Corrosion and Durability · Corrosion Behavior and Inhibition

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Faculty of Mechanical Engineering, Lublin University of Technology, Nadbystrzycka 36 St., 20-618 Lublin, Poland

Faculty of Management, Lublin University of Technology, Nadbystrzycka 38 St., 20-618 Lublin, Poland

Łukasiewicz Research Network—New Chemical Syntheses Institute, Al. Tysiąclecia Państwa Polskiego 13a, 24-110 Puławy, Poland

BORG Automotive Company, Metalurgiczna St. 13B, 20-001 Lublin, Poland

References (49)

Show source-provided references
1. Adams, R.D., Comyn, J., and Wake, W.C. (1997). Structural Adhesive Joints in Engineering, Chapman & Hall. [2nd ed.].
2. Surface treatment and solvent co-assisted easy direct bonding10.1016/j.matdes.2021.109641 ↗
3. Adhesion phenomena in bonded joints10.1016/j.ijadhadh.2012.04.007 ↗
5. Adhesion strength of cellulosic varnish coated wood species as function of their surface roughness10.1155/2015/525496 ↗
6. Functionalized plasma polymer coatings for improved durability of aluminium-epoxy adhesive joints: Fractography10.1002/1096-9918(200008)30:1<16::AID-SIA708>3.0.CO;2-J ↗
7. The effect of cataphoretic and powder coatings on the strength and failure modes of EN AW-5754 aluminium alloy adhesive joints10.1016/j.ijadhadh.2018.11.005 ↗
8. Pogorzelski, S., Boniewicz-Szmyt, K., Grzegorczyk, M., and Rochowski, P. (2022). Wettability of metal surfaces affected by paint layer covering. Materials, 15.10.3390/ma15051830 ↗
9. Color variation of electrophoretic styrene-acrylic paints under filed and accelerated ultraviolet exposure10.1016/j.matdes.2016.12.051 ↗
10. Galvanic corrosion protection and durability of polyaniline-reinforced epoxy adhesive for bond-riveted joints in AA5083/Cf/Epoxy laminates10.1016/j.matdes.2018.10.034 ↗
11. Effects of overlap length on the strength of bolted, bonded and hybrid single lap joints with different adherend materials and thicknesses10.1080/01694243.2019.1623966 ↗
12. Experimental and numerical analysis of single-lap joints for the automotive industry10.1016/j.ijadhadh.2008.09.001 ↗
13. Tserpes, K. (2020). Revolutionizing Aircraft Materials and Processes, Springer.
14. Experimental methods to capture curing induced effects in adhesive bonded joints10.1016/j.ijadhadh.2020.102735 ↗
15. An investigation on the mechanical behaviour of sandwich composite structures with circular honeycomb bamboo core10.1007/s44245-022-00006-z ↗
16. Optimized surface treatment of aerospace composites using a picosecond laser10.1016/j.compositesb.2019.107155 ↗
17. On the influence of resin pocket area on the failure of tapered sandwich composites10.1177/1369433220940816 ↗
18. An investigation on fatigue life evaluation and crack initiation of Al-GFRP bonded lap joints under four-point bending10.1016/j.compstruct.2019.111433 ↗
19. The effect of surface preparation on the bond strength of Al-St strips in CRB process10.1016/j.matdes.2016.05.112 ↗
20. On the effect of surface roughness height, wettability, and nanoporosity on Leidenfrost phenomena10.1063/1.3560060 ↗
21. Rudawska, A., Miturska-Barańska, I., Doluk, E., and Olewnik-Kruszkowska, E. (2022). Assessment of Surface Treatment Degree of Steel Sheets in the Bonding Process. Materials, 15.10.3390/ma15155158 ↗
22. Effect of material, geometry, surface treatment and environment on the shear strength of single lap joints10.1016/j.ijadhadh.2009.02.012 ↗
23. The effects of surface roughness on varnish adhesion strength of wood materials10.1007/s11998-016-9805-5 ↗
24. Micro-geometry surface modelling in the process of low-rigidity elastic-deformable shafts turning
25. The effect of grit-blasting on the surface properties for adhesion10.1016/S0143-7496(98)00061-X ↗
26. Influence of the surface chemistry on the wettability of stainless steel10.1002/sia.740210902 ↗
27. Surface treatment of stainless steel to improve coating strength of ZrO2 coated stainless steel needle10.1179/026708410X12593178265544 ↗
28. Jang, J., Wi, K., Lee, H.S., Singh, J.K., and Lee, H.H. (2023). Effects of surface treatment conditions on the bonding strength and electromagnetic pulse shielding of concrete using the 85Zn-15Al arc thermal metal spraying method. Materials, 16.10.3390/ma16041372 ↗
29. Marques, A.C., Mocanu, A., Tomić, N.Z., Balos, S., Stammen, E., Lundevall, A., Abrahami, S.T., Günther, R., de Kok, J.M.M., and Teixeira de Freitas, S. (2020). Review on Adhesives and Surface Treatments for Structural Applications: Recent Developments on Sustainability and Implementation for Metal and Composite Substrates. Materials, 13.10.3390/ma13245590 ↗
30. The role of chemical surface modification for structural adhesive bonding on polymers—Washability of chemical functionalization without reducing adhesion10.1016/j.ijadhadh.2019.102409 ↗
31. Effect of surface treatment on the shear strength of aluminium adhesive single-lap joint for automotive applications10.1016/j.ijadhadh.2015.12.023 ↗
32. Moldovan, E.R., Concheso Doria, C., Ocaña, J.L., Baltes, L.S., Stanciu, E.M., Croitoru, C., Pascu, A., Roata, I.C., and Tierean, M.H. (2022). Wettability and surface roughness analysis of laser surface texturing of AISI 430 stainless steel. Materials, 15.10.3390/ma15082955 ↗
33. Effects of geometrical characteristics of surface roughness on droplet wetting10.1063/1.2804425 ↗
34. Wetting behavior and drag reduction of superhydrophobic layered double hydroxides films on aluminium10.1016/j.apsusc.2016.01.208 ↗
35. Analysis of the surface energy interactions in the tribological behavior of ALCrN and TIAlN coatings10.1016/j.triboint.2020.106206 ↗
36. Rudawska, A. (2019). Surface Treatment in Bonding Technology, Academic Press Elsevier.10.1016/B978-0-12-817010-6.00002-3 ↗
37. Surface free energy of polymeric materials: Relevancy of conventional contact angle data analyses10.1163/156856199X00712 ↗
38. Evaluating uncertainty of surface free energy measurement by the van Oss-Chaudhury-Good method10.1016/j.ijadhadh.2018.01.006 ↗
39. Approaches to design a Surface with tunable wettability: A review on surface properties10.1007/s10853-020-05116-1 ↗
40. Static solvent contact angle measurements, surface free energy and wettability determination of various self-assembled monolayers on silicon dioxide10.1016/j.tsf.2006.04.006 ↗
41. Effect of wood moisture content on adhesion of varnish coatings
42. Influence of relative humidity on surface quality and adhesion strength of coated medium density fibreboard (MDF) panels10.1016/j.matdes.2008.09.036 ↗
43. Lollivier, G., Gressier, M., Ansart, F., Aufray, M., and Menu, M.-J. (2021). Influence of Hybrid Sol-Gel Crosslinker on Self-Healing Properties for Multifunctional Coatings. Materials, 14.10.3390/ma14185382 ↗
44. Sastri, V.R. (2022). Plastics in Medical Devices, William Andrew. [3rd ed.].
45. Rudawska, A. (2020). Experimental study of mechanical properties of epoxy compounds modified with calcium carbonate and carbon after hygrothermal exposure. Materials, 13.10.3390/ma13235439 ↗
46. (2023, July 24). Pearson Correlation Coefficient. Available online: https://en.wikipedia.org/wiki/Pearson_correlation_coefficient.
47. Constitutive relations in the wetting of low energy surfaces and the theory of the retraction method of preparing monolayers
48. Wetting phenomena on micro-grooved aluminium surfaces and modelling of the critical droplet size10.1016/j.jcis.2008.09.023 ↗
49. Rudawska, A., Miturska-Barańska, I., and Doluk, E. (2021). Influence of surface treatment on steel adhesive joints strength—Varnish coats. Materials, 14.10.3390/ma14226938 ↗