journal article·2022-12-30Open access

Effect of Interstage Pipeline on the Performance of Two-Stage Centrifugal Compressors for Automotive Hydrogen Fuel Cells

Huaiyu Wang, Dengfeng Yang, Zhengcan Zhu, Hongjie Zhang, Qian Zhang

Applied Sciences· Volume 13· Issue 1

Abstract

At present, two-stage centrifugal compressors based on air bearing and high-speed motor technology are widely used in automotive hydrogen fuel cells. The low-pressure stage and high-pressure stage of the compressor are directly connected through an interstage pipeline, thus the structure of the interstage pipeline has an important influence on the aerodynamic performance of the compressor. In this work, a two-stage compressor with three different interstage pipelines were investigated experimentally and numerically. Results show that affected by the interstage pipeline bend section, the flow distortion will be induced at the impeller inlet of the high-pressure stage, and the distortion intensity changes with the pipeline structure. Among the three models, the EPC (elbow pipe change) model induces the most intense total pressure distortion at the condition of 80 kr/min and 130% mass flow rate, resulting in an efficiency reduction of 2 and 1.5 percentage points compared with the SPC (straight pipe change) and the TPC (total pipe change) model, respectively. Further research indicates that the upstream distortion has obvious influence on the downstream rotor blades. As the blade height decreases, the load becomes more uniform on the main blades, while the load extremum migrates to the trailing edge on the splitter blades. Finally, three models are tested, and their performance is compared at three typical rotational speeds., It is recommended that interstage pipelines similar to SPC models should be chosen to improve the two-stage compressor efficiency in the design.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Turbomachinery Performance and Optimization · Refrigeration and Air Conditioning Technologies · Tribology and Lubrication Engineering

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

School of Control Engineering, Northeastern University at Qinhuangdao, Qinhuangdao 066004, China

School of Electrical Engineering, Southeast University, Nanjing 210018, China

School of Vehicle and Mobility, Tsinghua University, Beijing 100084, China

Funding

National Natural Science Foundation of China · Natural Science Foundation of Hebei Province · Central University Basic Scientific Research Business Fee Funding Project

References (34)

Show source-provided references
1. Degradation of the ionic pathway in a pem fuel cell cathode10.1021/jp2068599 ↗
2. Numerical prediction of mass-exchange between cathode and anode channels in a PEM fuel cell10.1016/S0017-9310(00)00257-X ↗
3. Three-dimensional transport model of PEM fuel cell with straight flow channels10.1016/j.jpowsour.2005.08.046 ↗
4. Numerical simulation of laminar flow development with heat and mass transfer in pem fuel cell flow channels having oxygen and hydrogen suction at one channel wall10.1002/er.1717 ↗
5. Numerical prediction of humidification process in planar porous membrane humidifier of a pem fuel cell system to evaluate the effects of operating and geometrical parameters10.1007/s10973-020-10058-6 ↗
6. Numerical simulation and experimental comparison of channel geometry on performance of a pem fuel cell10.1007/s13369-012-0312-4 ↗
7. Adaptive control for robust air flow management in an automotive fuel cell system10.1016/j.apenergy.2016.12.115 ↗
8. Feedforward fuzzy-PID control for air flow regulation of PEM fuel cell system10.1016/j.ijhydene.2015.04.080 ↗
9. Tracking the maximum efficiency point for the FC system based on extremum seeking scheme to control the air flow10.1016/j.apenergy.2014.05.002 ↗
10. Disturbance decoupling control of an ultra-high speed centrifugal compressor for the air management of fuel cell systems10.1016/j.ijhydene.2013.11.057 ↗
11. Investigation of using multi-shockwave system instead of single normal shock for improving radial inflow turbine reliability10.1016/j.ijheatfluidflow.2018.03.018 ↗
12. Characterization of a radial turbocharger turbine in pulsating flow by means of CFD and its application to engine modeling10.1016/j.apenergy.2012.09.013 ↗
13. An experimental assessment of the effects of stator vane tip clearance location and back swept blading on an automotive variable geometry turbocharger10.1115/1.4007517 ↗
14. A detailed investigation of a variable nozzle turbine with novel forepart rotation guide vane10.1177/0954407018757244 ↗
15. Semi-physical modeling and control of a centrifugal compressor for the air feeding of a pem fuel cell10.1016/j.enconman.2017.11.030 ↗
16. Gelfi, S., Stefanopoulou, A.G., Pukrushpan, J.T., and Peng, H. (2003, January 4–6). Dynamics of Low-Pressure and High-Pressure Fuel Cell Air Supply Systems. Proceedings of the American Control Conference, Denver, CO, USA.
17. Zheng, X., Zhang, Y., He, H., and Qiu, Z. (2008). Design of a centrifugal compressor with low specific speed for automotive fuel cell. Am. Soc. Mech. Eng., 1531–1536.10.1115/GT2008-50468 ↗
18. Performance improvement of centrifugal compressors for fuel cell vehicles using the aerodynamic optimization and data mining methods10.1016/j.ijhydene.2020.02.026 ↗
19. Performance improvement of a centrifugal compressor for the fuel cell vehicle by tip leakage vortex control10.1007/s11630-021-1430-7 ↗
20. Investigation of surge behavior in a micro centrifugal compressor10.1007/s11630-006-0097-4 ↗
21. Liu, Y., Lao, D., Yang, C., Wang, L., and Li, D. (2015, January 15–19). Aerodynamic Excitation and Forced Response of Centrifugal Compressor Impeller in Inlet Distortion. Proceedings of the ASME Turbo Expo 2015, Montreal, QC, Canada. No. GT2015-42201.10.1115/GT2015-42201 ↗
22. Numerical investigation of blade vibration response induced by inlet distortion in axial compressor
23. Parametric studies of pipe diffuser on performance of a highly loaded centrifugal compressor10.1115/1.4027867 ↗
24. Sheoran, Y., and Bouldin, B. (2008, January 9–13). A Versatile Design of a Controlled Swirl Distortion Generator for Testing Gas Turbine Engines. Proceedings of the ASME Turbo Expo 2008: Power for Land, Sea, and Air, Berlin, Germany.10.1115/GT2008-50657 ↗
25. The effect of inlet distortion on the performance characteristics of a centrifugal compressor10.1115/1.3227406 ↗
26. Zemp, A., Kammerer, A., and Abhari, R. (2008, January 9–13). Unsteady CFD Investigation on Inlet Distortion in a Centrifugal Compressor. Proceedings of the ASME Turbo Expo 2008: Power for Land, Sea, and Air, Berlin, Germany.10.1115/GT2008-50744 ↗
27. Brune, K.H., Schiffer, H.P., Christmann, R., and Gnewikow, M. (2009, January 8–12). Experimental Investigations of the Disturbed Inlet-Flow Structure Caused by Mixing Geometries and Its Influence on the Performance of a Turbocharger Centrifugal Compressor. Proceedings of the ASME Turbo Expo 2009: Power for Land, Sea, and Air, Orlando, FL, USA. GT2009-59534.10.1115/GT2009-59534 ↗
28. The influence of inlet flow distortion on the performance of a centrifugal compressor and the development of an improved inlet using numerical simulations10.1243/0957650011538550 ↗
29. The inlet flow structure of a centrifugal compressor stage and its influence on the compressor performance10.1115/1.1601255 ↗
30. Blade forcing function and aerodynamic work measurements in a high speed centrifugal compressor with inlet distortion10.1115/1.4000614 ↗
31. Dickmann, H., Wimmel, T., and Szwedowicz, J. (2005, January 6–9). Unsteady Flow in a Turbocharger Centrifugal Compressor: 3D-CFD-Simulation and Numerical and Experimental Analysis of Impeller Blade Vibration. Proceedings of the ASME Turbo Expo 2005: Power for Land, Sea, and Air, Reno, NV, USA.10.1115/GT2005-68235 ↗
32. Dickmann, H., Wimmel, T., and Szwedowicz, J. (2009, January 8–12). Unsteady Flow in a Turbocharger CENTRIFUGAL compressor: 3D-CFD Simulation, Impeller Blade Vibration and Vaned Diffuser-Volute Interaction. Proceedings of the ASME Turbo Expo 2009: Power for Land, Sea, and Air, Orlando, FL, USA.10.1115/GT2009-59046 ↗
33. The change of the inlet geometry of a centrifugal compressor stage and its influence on the compressor performance10.1007/s11630-013-0613-2 ↗
34. Numerical and experimental research on different inlet configurations of high speed centrifugal compressor10.1007/s11431-011-4635-2 ↗