Detection of Hydrogen Bubbles Produced by Corrosion Inhibition of Metal Weldment Using Machine Learning
Source abstract
Abstract
This study analyzes the corrosion inhibition efficiency of sodium molybdate (SM) solution on weldment specimens in 1 M HCl, based on H2 bubbles detection. The detection of the bubbles produced by the corrosion process is achieved by a YOLOv4 deep learning algorithm. The results indicate that the corrosion rate is higher on the weld metal zone than on the base metal zone in the same solution, which might be attributed to the coarser grain of the weld metal zone and the stability of the produced oxide layer. The addition of sodium molybdate was discovered to boost the stability of the oxide layer, hence enhancing the specimens’ corrosion resistance. The overall inhibitory efficiency of the sodium molybdate solution was 59% for the weld metal (WM) (0.4 g/L), 52% for the heat-affected zone (HAZ) (0.2 g/L), and 37% for the base metal (BM) (0.2 g/L). The object detection algorithm models showed 97% for the mAP and 0.98 for recall. The minimum average bubble detected for the WM was 0.353 /mm2 at an SM concentration of 0.4 g/L, while the HAZ was 0.612 /mm2 at 0.2 g/L, and the BM was 1.055 /mm2 at 0.2 g/L. The results of the bubbles detection appeared to be consistent with the corrosion experiment outcomes obtained by the potentiodynamic polarization and hydrogen volume measurement tests. This experiment validates the distinctiveness of the different weld zones in terms of the inhibitor concentration required for successful corrosion prevention, as well as the potential of analyzing corrosion using machine learning algorithms for object detection.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Corrosion Behavior and Inhibition · Hydrogen embrittlement and corrosion behaviors in metals · Non-Destructive Testing Techniques
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Department of Mechanical and Electro-Mechanical Engineering, National Sun Yat-Sen University, Kaohsiung 80424, Taiwan
Department of Mechanical Engineering, Universitas Brawijaya, Malang 65145, Indonesia
References (68)
Show source-provided references
1. Nuthalapati, S., Kee, K.E., Pedapati, S.R., and Jumbri, K. A Review of Chloride Induced Stress Corrosion Cracking Chracterization in Austenitic Stainless Steels Using Acoustic Emission Technique. Nucl. Eng. Technol., 2023. in press.10.1016/j.net.2023.11.005 ↗
2. Inhibition of API 5L X60 Steel Corrosion in CO2-Saturated 3.5% NaCl Solution by Tannic Acid and Synergistic Effect of KI Additive10.1016/j.molliq.2017.04.064 ↗
3. Experimental and Theoretical Studies of the Synergistic Inhibition Effects between the Plant Leaves Extract (PLE) and Zinc Salt (ZS) in Corrosion Control of Carbon Steel in Chloride Solution10.1016/j.molliq.2017.10.120 ↗
4. Utilization of Silicon from Lemongrass Ash Reinforcement with ADC 12 (Al-Si alloy) Aluminium on Mechanical and Tribological Properties10.1007/s12633-022-02119-2 ↗
5. Bee Wax Propolis Extract as Eco-Friendly Corrosion Inhibitors for 304SS in Sulfuric Acid10.1155/2015/567202 ↗
6. Analysis of Corrosion Inhibition of Kleinhovia Hospita Plant Extract Aided by Quantification of Hydrogen Evolution Using a GLCM/SVM Method10.1016/j.ijhydene.2023.01.067 ↗
7. Corrosion Inhibition of Welded of X—52 Steel Pipelines by Sodium Molybdate in 3.5% NaCl Solution10.1016/j.ejpe.2020.02.001 ↗
8. Gapsari, F., Darmadi, D.B., Setyarini, P.H., Izzuddin, H., Madurani, K.A., Tanji, A., and Hermawan, H. (2021). Nephelium lappaceum Extract as an Organic Inhibitor to Control the Corrosion of Carbon Steel Weldment in the Acidic Environment. Sustainibility, 13.10.3390/su132112135 ↗
9. Application of Corrosion Inhibitors for Steels in Acidic Media for the Oil and Gas Industry: A Review10.1016/j.corsci.2014.04.044 ↗
10. CMT+P welding process of UNS S32750 super duplex stainless steel
11. Microstructure and Corrosion Characterization of Weld Metal in Stainless Steel and Low Carbon Steel Joint under Different Heat Input10.1016/j.mtcomm.2021.102948 ↗
12. In Situ Corrosion Characterization of Simulated Weld Heat Affected Zone on API X80 Pipeline Steel10.1016/j.corsci.2014.04.053 ↗
13. Miranda-Perez, A.F., Rodriguez-Vargas, B.R., Calliari, I., and Pezzato, L. (2023). Corrosion Resistance of GMAW Duplex Stainless Steels Welds. Materials, 16.10.3390/ma16051847 ↗
14. Initiation Mechanism of Pitting Corrosion in Weld Heat Affected Zone of Duplex Stainless Steel10.1016/j.corsci.2022.110278 ↗
15. Investigation of Arc Stability, Microstructure Evolution and Corrosion Resistance in Underwater Wet FCAW of Duplex Stainless Steel10.1016/j.jmrt.2021.11.023 ↗
16. Effects of N2 Content in Shielding Gas on Microstructure and Toughness of Cold Metal Transfer and Pulse Hybrid Welded Joint for Duplex Stainless Steel10.1016/j.msea.2023.144936 ↗
17. Grain Size Distribution Effects on the Corrosion Behavior of Materials10.1016/j.corsci.2012.04.040 ↗
18. Investigating the corrosion of the Heat-Affected Zones (HAZs) of API-X70 pipeline steels in aerated carbonate solution by electrochemical methods10.1016/j.ijpvp.2016.06.001 ↗
19. Residual stress control of multipass welds using low transformation temperature fillers10.1080/02670836.2017.1410954 ↗
20. Confirmation of tensile residual stress reduction in electron beam welding using low transformation temperature materials (LTT) as localized metallurgical injection e Part 1: Metallographic analysis10.3139/120.110957 ↗
21. Microstructure, residual stress and mechanical properties of a high strength steel weld using low transformation temperature welding wires10.1016/j.matdes.2014.10.013 ↗
22. Confirmation of tensile residual stress reduction in electron beam welding using low transformation temperature materials (LTT) as localized metallurgical injections e Part 2: Residual stress measurement10.3139/120.111046 ↗
23. Effects of phase transition temperature and preheating on residual stress in multi-phase & multi-layer laser metal deposition10.1016/j.jallcom.2019.04.104 ↗
24. Prediction of residual stresses in high strength carbon steel pipe weld considering solid-state phase transformation effects10.1016/j.compstruc.2010.10.005 ↗
25. Influence of martensitic transformation on welding residual stress in plates and pipes10.1080/13621718.2016.1263711 ↗
26. Surface residual stresses in multipass welds produced using low transformation temperature filler alloys10.1179/1362171814Y.0000000234 ↗
27. Hydrogen embrittlement behavior of SUS301L-MT stainless steel laser-arc hybrid welded joint localized zones10.1016/j.corsci.2019.108337 ↗
28. A Nucleation Mechanism of Hydrogen Blister in Metals and Alloys10.1007/s11661-007-9391-3 ↗
29. Hydrogen damage and delayed fracture in bulk metallic glass10.1016/j.corsci.2004.07.045 ↗
30. Atomic mechanism and prediction of hydrogen embrittlement in iron10.1038/nmat3479 ↗
31. Atomistic simulation of hydrogen-assisted ductile-to-brittle transition in α-iron10.1016/j.commatsci.2016.10.033 ↗
32. Effects of dissolved hydrogen and elastic and plastic deformation on active dissolution of pipeline steel in anaerobic groundwater of near-neutral pH10.1016/j.actamat.2008.08.035 ↗
33. Mechanistic investigation of hydrogen-enhanced anodic dissolution of X-70 pipe steel and its implication on near-neutral pH SCC of pipelines10.1016/j.electacta.2007.07.015 ↗
34. Corrosion inhibition, hydrogen evolution and antibacterial properties of newly synthesized organic inhibitors on 316L stainless steel alloy in acid medium10.1016/j.ijhydene.2011.02.134 ↗
35. Chemically Modified Guar Gum and Ethyl Acrylate Composite as a New Corrosion Inhibitor for Reduction in Hydrogen Evolution and Tubular Steel Corrosion Protection in Acidic Environment10.1016/j.ijhydene.2020.12.103 ↗
36. Inhibition effect of newly Synthesized Heterocyclic Organic Molecules on Corrosion of Steel in Alkaline Medium Containing Chloride10.1016/j.ijhydene.2010.07.071 ↗
37. Accurate Electrochemical Measurement of Magnesium Corrosion Rates; a Combined Impedance, Mass-Loss and Hydrogen Collection Study10.1016/j.electacta.2013.12.124 ↗
38. Electrochemical Investigation on the Corrosion and Hydrogen Evolution Rate of Mild Steel in Sulphuric Acid Solution10.1016/j.ijhydene.2011.05.149 ↗
39. Hydrogen Evolution Reaction of Low Carbon Steel Electrode in Hydrochloric Acid as a Source for Hydrogen Production10.1016/j.ijhydene.2008.10.026 ↗
40. The Investigation of the Kinetics and Mechanism of Hydrogen Evolution Reaction on Tin10.1016/j.ijhydene.2006.08.043 ↗
41. Zhang, A., Lipton, Z.C., Li, M., and Smola, A.J. (2023). Dive into Deep Learning, Cambridge University Press.
42. Deep Learning: A Comprehensive Overview on Techniques, Taxonomy, Applications and Research Directions10.1007/s42979-021-00815-1 ↗
43. Redmon, J., Divvala, S., Girshick, R., and Farhadi, A. (2016, January 27–30). You Only Look Once: Unified, Real-Time Object Detection. Proceedings of the 2016 IEEE Conference on Computer Vision and Pattern Recognition (CVPR), Las Vegas, NV, USA.10.1109/CVPR.2016.91 ↗
44. Wang, C.Y., Bochkovskiy, A., and Liao, H.Y.M. (2021, January 19–20). Scaled YOLOv4: Scaling Cross Stage Partial Network. Proceedings of the IEEE/CVF Conference on Computer Vision and Pattern Recognition (CVPR), New Orleans, LA, USA.10.1109/CVPR46437.2021.01283 ↗
45. Bochkovskiy, A., Wang, C.-Y., and Liao, H.Y.M. (2020). YOLOv4: Optimal Speed and Accuracy of Object Detection. arXiv.
46. Prediction of Corrosion Inhibition Efficiency of Pyridines and Quinolines on an Iron Surface Using Machine Learning-Powered Quantitative Structure-Property Relationships10.1016/j.apsusc.2020.145612 ↗
47. Experimental Characterization, Machine Learning Analysis and Computational Modelling of the High Effective Inhibition of Copper Corrosion by 5-(4-pyridyl)-1,3,4-oxadiazole-2-thiol in Saline Environment10.1016/j.electacta.2021.139282 ↗
48. Machine Learning Modeling of Time-Dependent Corrosion Rates of Carbon Steel in Presence of Corrosion Inhibitors10.1016/j.corsci.2021.109904 ↗
49. (2012). Specification for Carbon Steel Electrodes for Shielded Metal Arc Welding (Standard No. AWS A5.1/A5.1M:2012).
50. Yun, S., Han, D., Chun, S., Oh, S.J., Yoo, Y., and Choe, J. (2019, January 27). CutMix: Regularization Strategy to Train Strong Classifiers with Localizable Features. Proceedings of the 2019 IEEE/CVF International Conference on Computer Vision (ICCV), Seoul, Republic of Korea.10.1109/ICCV.2019.00612 ↗
51. Ghiasi, G., Lin, T.-Y., and Le, Q.V. (2018, January 3). DropBlock: A Regularization Method for Convolutional Networks. Proceedings of the 32nd International Conference on Neural Information Processing Systems, Red Hook, NY, USA.
52. Misra, D. (2020). Mish: A Self Regularized Non-Monotonic Activation Function. arXiv.
53. Spatial Pyramid Pooling in Deep Convolutional Networks for Visual Recognition10.1109/TPAMI.2015.2389824 ↗
54. Ferrari, V., Hebert, M., Sminchisescu, C., and Weiss, Y. (2018). Proceedings of the Computer Vision—ECCV 2018, Springer.10.1007/978-3-030-01240-3 ↗
55. Liu, S., Lu, Q., Haifang, Q., Jianping, S., and Jiaya, J. (2018, January 18). Path Aggregation Network for Instance Segmentation. Proceedings of the IEEE/CVF Conference on Computer Vision and Pattern Recognition, Salt Lake City, UT, USA.10.1109/CVPR.2018.00913 ↗
56. Zheng, Z., Ping, W., Wei, L., Jinze, L., Rongguang, Y., and Dongwei, R. (February, January 27). Distance-IoU Loss: Faster and Better Learning for Bounding Box Regression. Proceedings of the AAAI Conference on Artificial Intelligence, Honolulu, HI, USA.
57. (2023, February 07). Alexey Yolo_Mark 2023. Available online: https://github.com/AlexeyAB/Yolo_mark.
58. Zimmermann, T., Hort, N., Zhang, Y., Müller, W.-D., and Schwitalla, A. (2021). The Video Microscopy-Linked Electrochemical Cell: An Innovative Method to Improve Electrochemical Investigations of Biodegradable Metals. Materials, 14.10.3390/ma14071601 ↗
59. An improved algorithm for small object detection based on YOLO v4 and multi-scale contextual information10.1016/j.compeleceng.2022.108490 ↗
60. (2023, July 03). NIST Chemistry WebBook, SRD 69, Available online: https://webbook.nist.gov/cgi/inchi?ID=B6000473&Mask=80.
61. Enhancing Corrosion Resistance, Hardness, and Crack Resistance in Magnetron Sputtered High Entropy CoCrFeMnNi Coatings by Adding Carbon10.1016/j.matdes.2021.109711 ↗
62. Effect of Weld Heat Input on Corrosion of Dissimilar Welded Pipeline Steels under Simulated Coating Disbondment Protected by Cathodic Protection10.1016/j.jmrt.2019.12.044 ↗
63. The Effect of β-FeOOH on the Corrosion Behavior of Low Carbon Steel Exposed in Tropic Marine Environment10.1016/j.matchemphys.2008.06.066 ↗
64. Preparation and Inhibition Properties of Molybdate Intercalated ZnAlCe Layered Double Hydroxide10.1016/j.jallcom.2016.03.281 ↗
65. Electrochemical Characheristic of Austenitic Stainless Steel in Mixed Chloride—Molybdate Solutions10.26552/com.C.2017.2A.74-78 ↗
66. Optimization of Inhibitive Action of Sodium Molybdate (IV) for Corrosion of Carbon Steel in Saline Water Using Response Surface Methodology10.1007/s11814-019-0291-1 ↗
67. Properties of Sodium Molybdate-Based Compound Corrosion Inhibitor for Hot-Dip Galvanized Steel in Marine Environment10.1515/corrrev-2022-0043 ↗
68. Corrosion Behavior of Mild Steel in Presence of 2-Chloromethylbenzimidazole and Sodium Molybdate in 1M HCl