journal article·2024-08-11Open access

Contact Force and Friction of Generally Layered Laminates with Residual Hygrothermal Stresses under Mode II In-Plane-Shear Delamination

Efstratios Polyzos, Danny Van Hemelrijck, Lincy Pyl

Applied Sciences· Volume 14· Issue 16

Abstract

Mode II (in-plane-shear) delamination tests are more complex than mode I (opening) due to the presence of a contact force between the two arms. This force is essential for the calculation of the energy release rate (ERR) and is closely linked to friction effects. A novel formulation is presented in this article to estimate the contact force analytically. Specifically, the contact force is derived within the context of the rigid, semi-rigid, and flexible joint models. The analytical solutions consider the case of a generally layered composite laminate with residual hygrothermal stresses and are used to evaluate the ERR. The new formulation is compared with numerical models created using the Virtual Crack Closure Technique (VCCT) and the Cohesive Zone Method (CZM) for a fiber–metal laminate. The results show that the new formulation provides nearly identical ERR predictions to those of the VCCT and CZM models. Additionally, it is demonstrated that the effect of friction on the ERR is less than 1%.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Mechanical Behavior of Composites · Tribology and Wear Analysis · Mechanical and Thermal Properties Analysis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Mechanics of Materials and Constructions, Vrije Universiteit Brussel (VUB), 1050 Brussels, Belgium

Funding

FWO Research Foundation–Flanders

References (50)

Show source-provided references
1. Standard test methods for delamination resistance of composite materials: Current status10.1023/A:1008869811626 ↗
2. Analysis of beam-type fracture specimens with crack-tip deformation10.1007/s10704-005-2181-2 ↗
3. Analytical model for the estimation of the hygrothermal residual stresses in generally layered laminates10.1016/j.engfracmech.2021.107667 ↗
4. Prediction of energy release rate for mixed-mode delamination using classical plate theory10.1115/1.3120829 ↗
5. Correction method for evaluation of interfacial fracture toughness of DCB, ENF and MMB specimens with residual thermal stresses10.1016/j.compscitech.2007.08.025 ↗
6. Mechanics of bimaterial interface: Shear deformable split bilayer beam theory and fracture10.1115/1.1978920 ↗
7. Improved method for calculating strain energy release rate based on beam theory10.2514/3.11965 ↗
8. Novel joint deformation models and their application to delamination fracture analysis10.1016/j.compscitech.2005.03.014 ↗
9. End corrections for orthotropic DCB specimens10.1016/0266-3538(89)90058-4 ↗
10. Determination of energy release rate and mode mix in three-dimensional layered structures using plate theory10.1023/A:1007672131026 ↗
11. On the energy release rate and mode mix of delaminated shear deformable composite plates10.1016/j.ijsolstr.2003.11.039 ↗
12. Energy release rates of bi-material interface crack including residual thermal stresses: Application of crack tip element method10.1016/j.engfracmech.2009.09.018 ↗
13. Effects of residual thermal stresses on the debond characterization of sandwich beams10.1177/0731684411407100 ↗
14. Hygrothermal effect on the strain energy release rates and mode mixity of asymmetric delaminations in generally layered beams10.1016/j.engfracmech.2019.03.006 ↗
15. Mechanics and fracture of crack tip deformable bi-material interface10.1016/j.ijsolstr.2004.06.006 ↗
16. An augmented double cantilever beam model for studying crack propagation and arrest10.1007/BF00035958 ↗
17. A dynamic analysis of unstable crack propagation and arrest in the DCB test specimen10.1007/BF00035502 ↗
18. (2014). Standard Test Method for Mode I Interlaminar Fracture Toughness of Unidirectional Fiber-Reinforced Polymer Matrix Composites (Standard No. ASTM D5528-01). American Standard of Testing Methods.
19. (2019). Standard Test Method for Determination of the Mode II Interlaminar Fracture Toughness of Unidirectional Fiber-Reinforced Polymer Matrix Composites (Standard No. ASTM D7905/D7905M-19e1).
20. (2014). Fibre-Reinforced Plastic Composites—Determination of the Mode II Fracture Resistance for Unidirectionally Reinforced Materials Using the Calibrated End-Loaded Split (C-ELS) Test and an Effective Crack Length Approach (Standard No. ISO 15114:2014).
21. On the calculation of energy release rates for cracked laminates with residual stresses10.1007/s10704-006-0044-0 ↗
22. Effects of test conditions on mode II interlaminar fracture toughness of four-point ENF specimens
23. Effects of friction, geometry, and fixture compliance on the perceived toughness from three-and four-point bend end-notched flexure tests10.1177/0731684405050402 ↗
24. Numerical evaluation of the effects of friction and geometric nonlinearities on the energy release rate in three-and four-point bend end-notched flexure tests10.1016/j.engfracmech.2005.11.007 ↗
25. Effect of compressive transverse normal stress on mode II fracture toughness in polymeric composites10.1007/s10704-007-9103-4 ↗
26. Frictional effect in mode II delamination: Experimental test and numerical simulation10.1016/j.engfracmech.2013.08.005 ↗
27. Analysis and evaluation of friction effects on mode II delamination testing10.1016/j.compstruct.2018.01.085 ↗
28. Extension-bending coupling phenomena and residual hygrothermal stresses effects on the Energy Release Rate and mode mixity of generally layered laminates10.1016/j.ijsolstr.2023.112297 ↗
29. Reddy, J.N. (2003). Mechanics of Laminated Composite Plates and Shells: Theory and Analysis, CRC Press.10.1201/b12409 ↗
30. Delamination analysis of layered structures with residual stresses and transverse shear deformation10.1061/(ASCE)EM.1943-7889.0000561 ↗
31. Stresses in bi-metal thermostats10.1115/1.3171827 ↗
32. Novel beam analysis of end-notched flexure specimen for mode-II fracture10.1016/S0013-7944(03)00096-1 ↗
33. Energy release rates for the ENF specimen using a beam on an elastic foundation10.1177/002199839502901101 ↗
34. On the calculation of energy release rates for cracked laminates10.1007/BF00017790 ↗
35. The analysis of interlaminar fracture in uniaxial fibre-polymer composites10.1098/rspa.1990.0007 ↗
36. Polyzos, E. (2022, January 26–30). Stochastic analytical and numerical modelling of interface stressses for generally layered 3D-printed composites. Proceedings of the 20th European Conference on Composite Mechanics: Composites Meet Sustainability, Lausanne, Switzerland.
37. Delamination analysis of 3D-printed nylon reinforced with continuous carbon fibers
38. Quantification of fibre bridging in Mode I cracked Glare without delaminations10.1016/j.euromechsol.2013.09.005 ↗
39. Smith, M. (ABAQUS/Standard User’s Manual, 2009). ABAQUS/Standard User’s Manual, Version 6.9.
40. Numerical simulation of delamination growth in layered composite plates
41. ICASE Report No 2002-10: The virtual crack closure technique: History, approach and applications10.1115/1.1595677 ↗
42. Krueger, R. (2015). The Virtual Crack Closure Technique for Modeling Interlaminar Failure and Delamination in Advanced Composite Materials, Elsevier Ltd.10.1016/B978-0-08-100332-9.00001-3 ↗
43. Yielding of steel sheets containing slits10.1016/0022-5096(60)90013-2 ↗
44. Barenblatt, G.I. (1962). Mathematical Theory of Equilibrium Cracks in Brittle Failure. Adv. Appl. Mech., 7.10.1016/S0065-2156(08)70121-2 ↗
45. An engineering solution for mesh size effects in the simulation of delamination using cohesive zone models10.1016/j.engfracmech.2006.08.025 ↗
46. A finite element calculation of stress intensity factors by a modified crack closure integral10.1016/0013-7944(77)90013-3 ↗
47. Measurement of mixed-mode delamination fracture toughness of unidirectional glass/epoxy composites with mixed-mode bending apparatus10.1016/0266-3538(96)00005-X ↗
48. Polyzos, E., Van Hemelrijck, D., and Pyl, L. (2023). An Open-Source ABAQUS Plug-In for Delamination Analysis of 3D Printed Composites. Polymers, 15.10.3390/polym15092171 ↗
49. The role of fillers on friction and slide wear characteristics in glass-epoxy composite systems
50. Energy release rate of beam-type fracture specimens with hygrothermal influence10.1177/1056789516669217 ↗