Fracture Mechanisms of Electrothermally Fatigued 631 Stainless Steel Fine Wires for Probe Spring Applications
Source abstract
Abstract
This study systematically investigates 50 μm-diameter 631 stainless steel fine wires subjected to both sequential and simultaneous electrothermomechanical loading to simulate probe spring conditions in microelectronic test environments. Under cyclic current loading (~104 A/cm2), the 50 μm 631SS wire maintained electrical integrity up to 0.30 A for 15,000 cycles. Above 0.35 A, rapid oxide growth and abnormal grain coarsening resulted in surface embrittlement and mechanical degradation. Current-assisted tensile testing revealed a transition from recovery-dominated behavior at ≤0.20 A to significant thermal softening and ductility loss at ≥0.25 A, corresponding to a threshold temperature of approximately 200 °C. These results establish the endurance limit of 631 stainless steel wire under coupled thermal–mechanical–electrical stress and clarify the roles of Joule heating, oxidation, and microstructural evolution in electrical fatigue resistance. A degradation map is proposed to inform design margins and operational constraints for fatigue-tolerant, electrically stable interconnects in high-reliability probe spring applications.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Microstructure and Mechanical Properties of Steels · Hydrogen embrittlement and corrosion behaviors in metals · Mechanical stress and fatigue analysis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Department of Materials Science and Engineering, National Cheng Kung University, No. 1, Daxue Rd., East Dist., Tainan City 70101, Taiwan
References (38)
Show source-provided references
1. Application of laser spot cutting on spring contact probe for semiconductor package inspection10.1016/j.optlastec.2017.06.005 ↗
2. A Universal Spring-Probe System for Reliable Probing of Electrochemical Lab-on-a-Chip Devices10.3390/s140100944 ↗
3. Effect of temperature on strength and elastic modulus of high-strength steel10.1061/(ASCE)MT.1943-5533.0000600 ↗
4. MEMS spring probe for non-destructive wafer level chip test10.1088/0960-1317/15/5/008 ↗
5. Fabrication of highly conductive stressed-metal springs and their use as sliding-contact interconnects10.1016/S0167-9317(03)00174-6 ↗
6. Experimental study of localization in thin wires10.1103/PhysRevB.22.5635 ↗
7. In-operando fatigue behavior of gold metallization lines on polyimide substrate10.1016/j.scriptamat.2020.04.021 ↗
8. Experimental and Numerical Investigation of Electromigration Behavior of Printed Silver Wire Under High Current Density10.1115/1.4055469 ↗
9. Failure of microelectromechanical systems subjected to impulse loads10.1016/j.ijsolstr.2007.08.004 ↗
10. Mechanical properties and applications of custom-built gold AFM cantilevers10.1016/j.mechatronics.2016.05.015 ↗
11. Recent developments in stainless steels10.1016/j.mser.2009.03.001 ↗
12. New application of stainless steel10.1016/S1006-706X(06)60028-9 ↗
13. Moon, J., Ha, H.Y., Kim, K.W., Park, S.J., Lee, T.H., Kim, S.D., and Lee, C.H. (2020). A new class of lightweight, stainless steels with ultra-high strength and large ductility. Sci. Rep., 10.10.1038/s41598-020-69177-7 ↗
14. Batch mode micro-electro-discharge machining10.1109/84.993444 ↗
15. Effect of repeated-tempering induced martensite on the microstructural evolution in 17–7 PH stainless steel10.1016/j.matchar.2024.114091 ↗
16. Nanoscale precipitates as sustainable dislocation sources for enhanced ductility and high strength10.1073/pnas.1914615117 ↗
17. Long, H., Zhou, X., Ma, Y., Li, K., and Ren, J. (2024). The Effect of Heat Treatment on the Plasma Nitriding of Hot-Rolled 17–7 PH Stainless Steel. Metals, 14.10.3390/met14091061 ↗
18. The Effect of Aging Conditions on the Stress Relaxation Behavior of 17-7PH Stainless Steel10.4028/www.scientific.net/MSF.1016.1664 ↗
19. Pervikov, A.V. (2016). Structural and phase transformations in zinc and brass wires under heating with high-density current pulse. Phys. Plasmas, 23.10.1063/1.4953418 ↗
20. Study on Material Properties and Copper-to-Copper Wire Bonding of Cu-Pt-Au-Pd Fine Micro-Alloyed Wires10.1007/s11664-024-11456-4 ↗
21. Comparison of the Microstructural Characteristics and the Electrothermal Fracture Mechanism of Au-Pd-Coated Copper Wire and Cu-Ti Micro-alloyed Wire10.1007/s11664-024-10944-x ↗
22. The effect of cold work on structure and properties of AISI 304 stainless steel10.1016/j.jmatprotec.2007.09.080 ↗
23. Microstructure and texture development during cold rolling in UNS S32205 and UNS S32760 duplex stainless steels10.1007/s11661-017-4026-9 ↗
24. Microstructure and mechanical properties of cold-drawn pearlitic wires affect by inherited texture10.1016/j.matdes.2015.04.036 ↗
25. Unravelling thermal history during additive manufacturing of martensitic stainless steel10.1016/j.jallcom.2020.157555 ↗
26. Contact melting of aluminum-silicon structures under conditions of thermal shock10.4028/www.scientific.net/KEM.771.118 ↗
27. Stress concentration in the bulk Cr2O3: Effects of temperature and point defects10.1155/2017/7039436 ↗
28. Decomposition of Austenite in Austenitic Stainless Steels10.2355/isijinternational.42.325 ↗
29. Effects of deformation on decomposition of austenite: Part II–Carbide precipitation10.1179/msc.1980.14.5.184 ↗
30. Effect of Al content on the high-temperature oxidation behavior of 18Cr–Al–Si ferritic heat-resistant stainless steel10.1016/j.jmrt.2021.02.024 ↗
31. Improvement of high-temperature oxidation resistance and strength in alumina-forming austenitic stainless steels10.1016/j.matlet.2011.07.021 ↗
32. Blonde, R.J.P. (2014). Austenite Stability in TRIP Steels Studied by Synchrotron Radiation. [Ph.D. Dissertation, Eindhoven University of Technology].
33. Influence of Warm Predeformation Temperature on the Corrosion Property of Type 304 Austenitic Stainless Steel10.1007/s11665-020-04954-z ↗
34. Change in electrical resistivity of commercial purity aluminium severely plastic deformed10.1080/14786435.2010.510453 ↗
35. Thermal decomposition of the (15× 3) R14° two-dimensional carbide on the W (110) surface10.1016/0039-6028(90)90179-C ↗
36. Temperature dependence of strain hardening and plastic instability behaviors in austenitic stainless steels10.1016/j.actamat.2004.05.003 ↗
37. The observation of stress effects during the high temperature oxidation of iron10.1007/BF00540812 ↗
38. Formation of shear bands and strain-induced martensite during plastic deformation of metastable austenitic stainless steels10.1016/j.actamat.2007.07.015 ↗