Influence of Groove Structure Parameters Based on Optimal Mass Transfer Coefficient on Vaporization Characteristics and Sealing Performance of Liquid Film Mechanical Seals
Source abstract
Abstract
In this study, a spiral groove liquid film vaporization model based on the viscosity–temperature equation, fluid internal friction, saturation temperature, and pressure relationship equation was established. Using a multiphase flow model based on the finite volume method, the influence of the change in the mass transfer coefficient on the vaporization of the liquid film was studied. Moreover, the influence law of structural parameter changes in liquid film vaporization characteristics and sealing performance was analyzed. The results indicate that, with an increase in the mass transfer coefficient, the average vapor phase volume fraction first increases and then gradually stabilizes. When calculating the average vapor phase volume fraction, it is necessary to consider the influence of the mass transfer coefficient, whereas its effect on the opening force and leakage can usually be neglected. Under the optimal mass transfer coefficient conditions, the average vapor phase volume fraction increases with an increase in the helix angle, groove-weir ratio, and groove depth. By comparison, with an increase in the groove-diameter ratio, the average vapor phase volume fraction first increases and then decreases. The opening force decreases with an increase in the helix angle, groove-to-weir ratio, and groove depth. On the other hand, it first decreases and then increases with an increase in the groove-diameter ratio. The leakage rate increases first and then stabilizes with an increase in the helix angle. Moreover, it increases continuously with an increase in the groove-diameter ratio, groove-weir ratio, and groove depth.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Tribology and Lubrication Engineering · Aerodynamics and Fluid Dynamics Research · Heat Transfer Mechanisms
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
School of Mechanical and Electrical Engineering, Nanjing Forestry University, 159 Long Pan Road, Nanjing 210037, China
Funding
National Key Research and Development Program of China · National Natural Science Foundation of China · Key R&D Program of Jiangsu Province
References (35)
Show source-provided references
1. Research and progress of mechanical seals operating with vaporization transition
2. A TEHD lubrication analysis of surface textured mechanical seals
3. Analysis and study on failure mechanism of mechanical seals in running
4. Zhang, X., Shi, J., Wang, S., Zhang, C., and Tomovic, M. (2016, January 5–7). Leakage model and failure factors analysis of mechanical seals. Proceedings of the 2016 IEEE 11th Conference on Industrial Electronics and Applications (ICIEA), Hefei, China.10.1109/ICIEA.2016.7603796 ↗
5. Overview on liquid film cavitation in mechanical seal faces
6. Experimental research on drag reduction characteristics of underwater vehicle during pitching
7. Research progress on the liquid face seal of vapor-liquid Two-Phase flow
8. Zwart, P.J., Gerber, A.G., and Belamri, T. (June, January 30). A two-phase flow model for predicting cavitation dynamics. Proceedings of the 5th International Conference on Multiphase Flow, Yokohama, Japan.
9. Habil, S.I. (June, January 27). Physical and numerical modeling of unsteady cavitation dynamics. Proceedings of the 4th International Conference on Multiphase Flow, New Orleans, LA, USA.
10. Mathematical basis and validation of the full cavitation model10.1115/1.1486223 ↗
11. Lattice Boltzmann modeling of transport phenomena in fuel cells and flow batteries10.1007/s10409-017-0667-6 ↗
12. Consistent simulation of droplet evaporation based on the phase-field multiphase lattice Boltzmann method10.1103/PhysRevE.90.033305 ↗
13. Lattice Boltzmann modeling of boiling heat transfer: The boiling curve and the effects of wettability10.1016/j.ijheatmasstransfer.2015.01.136 ↗
14. Lee, W.H. (1980). Pressure iteration scheme for Two-Phase flow modeling. Multiphase Transport Fundamentals, Reactor Safety, Applications, Hemisphere Publishing.
15. Influence of cavitation thermal effect on lubrication properties of upstream pumping mechanical seal
16. Analysis of internal friction and viscosity-temperature effect on vaporization and properties of sealing liquid film
17. Influence of operating parameters on vaporization characteristics and properties of liquid film of mechanical seal10.1186/s10033-019-0318-x ↗
18. Shi, J.X. (2013). Analysis of Mechanical Seal Phase Transition Radisu and Temperature, Beijing University of Chemical Technology.
19. Liu, H.H. (2014). Study on Performance of End Face Seals Used in the Condition of Low Temperature and Easily Vaporized Liquid Medium, Beijing University of Chemical Technology.
20. Effect of phase change on performance of spiral groove liquid film seals
21. Performance analysis of internal pressure type spiral groove liquid film seals based on phase change
22. Phase change phenomenon and properties of double spiral groove liquid film seals
23. A Multi-Objective optimization approach on spiral grooves for gas mechanical seals10.1115/1.4038864 ↗
24. Closure to Discussion of “A Multi-Objective optimization approach on spiral grooves for gas mechanical seals” (X. Wang, L. Shi, W. Huang, and X. Wang, 2018, ASME J. Tribol., 140(4), p. 041701)10.1115/1.4041076 ↗
25. Optimum analysis of vaporization and phase change performance of spiral groove hydrodynamic seal liquid film
26. Numerical model of two-phase mechanical face seal with shallow grooves based on finite volume method10.1108/ILT-12-2019-0537 ↗
27. Numerical simulation of laminar liquid film condensation in a horizontal circular minichannel
28. Numerical and experimental investigation of two phase flow during boiling in a coiled tube10.1016/j.ijheatmasstransfer.2007.05.025 ↗
29. Zhu, Z., Li, J., Peng, H., and Liu, D. (2021). Nature-Inspired Structures Applied in Heat Transfer Enhancement and Drag Reduction. Micromachines, 12.10.3390/mi12060656 ↗
30. Analysis on the value of coefficient of mass transfer with phase change in Lee’s equation
31. Performance analyses of the spiral groove dry gas seal with inner annular groove10.4028/www.scientific.net/AMM.420.51 ↗
32. ANSYS Inc. (2011). ANSYS14. 0 FLUENT Theory Guid, ANSYS Inc.
33. Wallis, G.B. (1969). One-Dimensional Two-Phase Flow, McGraw-Hill Companies.
34. Li, X.W. (2019). Research on Vaporization Characteristics of Fluid Film and Performance in Hydrodynamic Mechanical Seals, Jiangsu University.
35. Hu, K., and Li, Z.B. (2014). ANSYS ICEM CFD Engineering Examples in Detail, POSTS & TELECOM PRESS.