journal article·2021-01-06Open access

The Effects of Multi-Stage Homogenizations on the Microstructures and Mechanical Properties of Al–Zn–Mg–Zr–Sc Alloys

Yang-Chun Chiu, Tse-An Pan, Mien-Chung Chen, Jun-Wei Zhang, Hui-Yun Bor, Sheng-Long Lee

Applied Sciences· Volume 11· Issue 2

Abstract

This study is aimed at exploring the effects of multi-stage homogenization and trace amounts of Zr and Sc on the microstructures, mechanical properties, and recrystallization of Al–4.5Zn–1.5Mg alloys. The mechanical properties of the AA7005 aluminum alloys after the T6 heat treatment were evaluated through a hardness test and tensile test. The microstructures were analyzed by an optical microscope (OM), a differential scanning calorimeter (DSC), a transmission electron microscope (TEM), a scanning electron microscope (SEM), and electron backscattered diffraction (EBSD). The results show that the grain refinement effect of the as-cast, homogenized, and recrystallized Al–4.5Zn–1.5Mg alloy containing 0.05Sc (wt%) after the T6 heat treatment was more significant than that of the alloy containing 0.1Zr (wt%). In addition, compared with the aforementioned one-stage homogenization heat treatment, the two-stage homogenization made the dispersed grain phase (Al3Zr/Al3Sc) smaller. As a result, the T6 mechanical strength of the alloy after the two-stage homogenization heat treatment was better than that of the contrastive alloy after the one-stage homogenization heat treatment. However, the two different homogenization heat treatments caused a greater divergence between the sizes of the dispersed grain phases of the Al–4.5Zn–1.5Mg alloys containing Zr than between the sizes of the dispersed grain phases of the alloys containing Sc. Therefore, after the two-stage homogenization heat treatment, the alloy with 0.1Zr (wt%) promoted the mechanical properties better than the alloy with 0.05Sc (wt%).
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Microstructure and mechanical properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Institute of Materials Science and Engineering, National Central University, Jhongli 32001, Taiwan

Department of Mechanical Engineering, Minghsin University of Science and Technology, Hsinchu 30401, Taiwan

References (27)

Show source-provided references
1. Davis, J.R. (1993). ASM Specialty Handbook: Aluminum and Aluminum Alloys, ASM International.
2. Application of modern aluminum alloys to aircraft10.1016/0376-0421(95)00004-6 ↗
3. Current state and the future of aluminum-alloy application for rolling stock
4. Davis, J.R. (2007). ASM Specialty Handbook: Aluminum and Aluminum Alloys, ASM International.
5. Sci-entific principles of making an alloying addition of scandium to aluminium alloys10.1016/S0921-5093(99)00652-8 ↗
6. Ambient- and high- temperature me-chanical properties of isochronally aged Al-0.06Sc, Al-0.06Zr and Al-0.06Sc-0.06Zr (at.%) alloys10.1016/j.actamat.2010.10.017 ↗
7. Effect of mi-nor Sc and Zr on recrystallization behavior and mechanical properties of novel Al-Zn-Mg-Cu alloys10.1016/j.jallcom.2015.10.122 ↗
8. Grain structure effect on quench sensitivity of Al−Zn−Mg−Cu−Cr alloy10.1016/S1003-6326(16)64319-4 ↗
9. Precipitation evolution in Al–Zr and Al–Zr–Ti alloys during isothermal aging at 375–425 °C10.1016/j.actamat.2007.09.004 ↗
10. Effects of Mg addition on the kinetics of low tem-perature precipitation in Al-Li-Cu-Ag-Zr alloys10.1016/S0921-5093(97)00530-3 ↗
11. Role of vacancies on the precipitation process in Zr modified aluminum based alloys
12. Monte Carlo simulation of the microstructure evolution of Al-Zn-Mg-(Sc)-(Zr) alloys during the initial aging stage
13. Effects of two-step homogenization on precipitation behavior of Al3Zr dispersoids and recrystallization resistance in 7150 aluminum al-loy10.1016/j.matchar.2015.02.016 ↗
14. Humphreys, F.J., and Hatherly, M. (2017). Recrystallization and Related Annealing Phenomena, Elsevier Science Inc.. [3rd ed.].
15. Effect of one-step and two-step ho-mogenization treatments on distribution of Al3Zr dispersoids in commercial AA7150 aluminium alloy10.1016/S1003-6326(11)61512-4 ↗
16. Effect of homogenization and aging treatment on mechanical properties and stress-corrosion cracking of 7050 alloys10.1007/s11661-007-9200-z ↗
17. Three-stage homogeni-zation of Al–Zn–Mg–Cu alloys containing trace Zr10.1007/s11661-013-1639-5 ↗
18. Optimizing the homogenization of zirconium containing commercial aluminium alloys using a novel process model10.1016/S0921-5093(02)00061-8 ↗
19. Effect of three-stage homogeniza-tion on mechanical properties and stress corrosion cracking of Al-Zn-Mg-Zr alloys10.1016/j.msea.2016.08.071 ↗
20. (2020, December 24). ASTM B221M-13, Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes (Metric). Available online: https://shop.bsigroup.com/ProductDetail/?pid=000000000030286610.
21. Microstructure, mechanical properties and stress corrosion cracking of Al-Zn-Mg-Zr alloy sheet with trace amount of Sc10.1016/j.jallcom.2015.08.011 ↗
22. (2020, December 24). ASTM E8/E8M—16a, Standard Test Methods for Tension Testing of Metallic Materials. Available online: https://www.astm.org/DATABASE.CART/HISTORICAL/E8E8M-16A.htm.
23. Scandium in aluminium alloys overview: Physical metallurgy, properties and applications
24. The Effect of Compositional Variations on the Characteris-tics of Coarse Intermetallic Particles in Overaged 7xxx Al Alloys10.1179/026708301101509449 ↗
25. Humphreys, F.J., and Hatherly, M. (2004). Recrystallization and Related Annealing Phenomena- Grain Growth Following Recrystallization, Elsevier Ltd.. Chapter 11.10.1016/B978-008044164-1/50006-2 ↗
26. Improved quench sensitivity in modified alumi-num alloy 7175 for thick forging applications10.1016/S0921-5093(03)00653-1 ↗
27. Influence of quench-induced precipitation on aging behavior of Al-Zn-Mg-Cu al-loy10.1016/S1003-6326(11)61313-7 ↗