Microstructure and tensile property of a precipitation strengthened high entropy alloy processed by selective laser melting and post heat treatment
Source abstract
Abstract
The microstructure and tensile property of Al0.2Co1.5CrFeNi1.5Ti0.3 high entropy alloy (HEA) processed by selective laser melting (SLM) have been studied in comparisons to that fabricated by traditional cast & wrought (C&W) route. The C&W samples were annealed and then aged at 750 ℃ for 50 h to promote precipitation strengthening of L12 structured phase in FCC matrix. By contrast, SLM samples were aged directly at 750 ℃ for 50 h from the as-built condition, which possessed sub-micron dendritic segregation, internal stress and nano oxides; the result was a microstructure with not only L12 particles dispersion, but also L21 phase was formed at subgrain boundaries, nano oxides and dislocations were present in the matrix. The tensile properties of this HEA were significantly enhanced by the SLM and direct ageing process; the room temperature yield strength (1235 MPa) and ultimate tensile strength (1550 MPa) achieved in this work are the highest to-date for HEAs subjected to laser additive manufacturing processes. Comparing to those of C&W samples, the SLM samples at room temperature and 500 °C exhibited additional yield strengths of 284 MPa and 229 MPa, and additional ultimate tensile strengths of 240 MPa and 275 MPa, respectively. The degree of L12 phase precipitation strengthening was similar for both SLM and C&W samples subjected to the same ageing treatment, interestingly, the additional microstructure features of SLM sample provided extra strengthening contributions; detailed analysis on microstructure evolution and strengthening factors are presented and discussed in this article.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: High Entropy Alloys Studies · Additive Manufacturing Materials and Processes · High-Temperature Coating Behaviors
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (61)
Show source-provided references
1. A critical review of high entropy alloys and related concepts10.1016/j.actamat.2016.08.081 ↗
2. The evolution of microstructures and high temperature properties of AlxCo1. 5CrFeNi1. 5Tiy high entropy alloys10.1016/j.jallcom.2015.09.042 ↗
3. A precipitation-hardened high-entropy alloy with outstanding tensile properties10.1016/j.actamat.2015.08.076 ↗
4. A review on fundamental of high entropy alloys with promising high–temperature properties10.1016/j.jallcom.2018.05.067 ↗
5. Enhanced mechanical properties of HfMoTaTiZr and HfMoNbTaTiZr refractory high-entropy alloys10.1016/j.intermet.2015.03.013 ↗
6. The sliding wear behaviour of CoCrFeMnNi and AlxCoCrFeNi high entropy alloys at elevated temperatures10.1016/j.wear.2019.03.002 ↗
7. Recent advances on high-entropy alloys for 3D printing10.1002/adma.201903855 ↗
8. Metal additive manufacturing: a review10.1007/s11665-014-0958-z ↗
9. Metallic materials fabrication by selective laser melting: a review
10. The microstructure and mechanical properties of deposited-IN718 by selective laser melting10.1016/j.jallcom.2011.10.107 ↗
11. Effects of build direction and heat treatment on creep properties of Ni-base superalloy built up by additive manufacturing10.1016/j.scriptamat.2016.10.035 ↗
12. Effect of standard heat treatment on the microstructure and mechanical properties of selective laser melting manufactured Inconel 718 superalloy10.1016/j.msea.2015.06.021 ↗
13. Microstructure and property of a selective laser melting process induced oxide dispersion strengthened 17-4 PH stainless steel10.1016/j.jallcom.2019.06.289 ↗
14. Selective laser melting of an equiatomic CoCrFeMnNi high-entropy alloy: processability, non-equilibrium microstructure and mechanical property10.1016/j.jallcom.2018.02.298 ↗
15. Printability and microstructure of the CoCrFeMnNi high-entropy alloy fabricated by laser powder bed fusion10.1016/j.matlet.2018.04.052 ↗
16. Hierarchical microstructure and strengthening mechanisms of a CoCrFeNiMn high entropy alloy additively manufactured by selective laser melting10.1016/j.scriptamat.2018.05.015 ↗
17. Microstructures and properties of an equimolar AlCoCrFeNi high entropy alloy printed by selective laser melting10.1016/j.intermet.2018.10.018 ↗
18. Selective laser melting of Al0.3CoCrFeNi high-entropy alloy: printability, microstructure, and mechanical properties10.1007/s11837-019-03715-1 ↗
19. Selective laser melting of an equiatomic AlCrCuFeNi high-entropy alloy: processability, non-equilibrium microstructure and mechanical behavior10.1016/j.jallcom.2018.08.290 ↗
20. Selective laser melting enabling the hierarchically heterogeneous microstructure and excellent mechanical properties in an interstitial solute strengthened high entropy alloy10.1080/21663831.2019.1650131 ↗
21. Selective laser melted equiatomic CoCrFeMnNi high-entropy alloy: microstructure, anisotropic mechanical response, and multiple strengthening mechanism10.1016/j.jallcom.2019.07.106 ↗
22. Al0.5FeCoCrNi high entropy alloy prepared by selective laser melting with gas-atomized pre-alloy powders10.1016/j.msea.2018.10.035 ↗
23. Mechanical and corrosion properties of CoCrFeNiTi-based high-entropy alloy additive manufactured using selective laser melting
24. Effect of SLM processing parameters on microstructures and mechanical properties of Al0.5CoCrFeNi high entropy alloys10.3390/met10020292 ↗
25. Selective laser melting of dual phase AlCrCuFeNix high entropy alloys: formability, heterogeneous microstructures and deformation mechanisms
26. Effects of annealing on the structure and mechanical properties of FeCoCrNi high-entropy alloy fabricated via selective laser melting
27. Enhanced age hardening effects in FCC based Co1.5CrFeNi1.5 high entropy alloys with varying Ti and Al contents10.1016/j.mtla.2020.100823 ↗
28. The formation of cellular precipitate and its effect on the tensile properties of a precipitation strengthened high entropy alloy10.1016/j.matchemphys.2017.09.057 ↗
29. An evaluation of methods to determine the porosity of calcium phosphate cements10.1002/jbm.b.33173 ↗
30. Formation of a Huesler-like L21 phase in a CoCrCuFeNiAlTi high-entropy alloy10.1016/j.scriptamat.2014.12.006 ↗
31. Characterisation of L21-ordered Ni2TiAl precipitates in FeMn maraging steels10.1016/j.matchar.2016.05.026 ↗
32. Architecture and magnetism of alnico10.1016/j.actamat.2014.04.044 ↗
33. Phase relation and microstructure in Ni3Al–Ni3Ti–Ni3Nb pseudo-ternary alloy system10.1016/S0966-9795(01)00131-5 ↗
34. Effect of ternary additions on the room temperature lattice parameter of Ni3Al10.1002/pssa.2211330203 ↗
35. Investigations within the quaternary system titanium-nickel-aluminium-carbon10.1007/BF00798317 ↗
36. Fabric analysis of Allende matrix using EBSD10.1111/j.1945-5100.2006.tb00499.x ↗
37. Meyers · 2008
38. Novel TiB2-reinforced 316L stainless steel nanocomposites with excellent room- and high-temperature yield strength developed by additive manufacturing10.1016/j.compositesb.2018.07.050 ↗
39. Reed · 2008
40. Strengthening mechanisms in polycrystalline nickel-based superalloys10.1080/02670836.2018.1461594 ↗
41. Modelling of the influence of alloy composition on flow stress in high-strength nickel-based superalloys10.1016/j.actamat.2014.04.075 ↗
42. Encyclopedia of materials
43. Poisson’s ratio for metals and alloys10.1179/095066061790425893 ↗
44. Courtney · 2005
45. The mechanism of plastic deformation of crystals. Part I.—theoretical10.1098/rspa.1934.0106 ↗
46. Influence of microstructural parameters on the mechanical properties of oxide dispersion strengthened Fe-14Cr steels10.1016/j.actamat.2017.01.026 ↗
47. Study of the deformation mechanisms in a Fe–14% Cr ODS alloy10.1016/j.jnucmat.2011.10.046 ↗
48. Butler · 1969
49. Enhanced tensile yield strength in laser additively manufactured Al0.3CoCrFeNi high entropy alloy10.1016/j.mtla.2019.100522 ↗
50. Additive manufacturing of metals: a brief review of the characteristic microstructures and properties of steels, Ti-6Al-4V and high-entropy alloys10.1080/14686996.2017.1361305 ↗
51. Yield strength increase of a CoCrNi medium entropy alloy by interstitial nitrogen doping at maintained ductility10.1016/j.scriptamat.2019.12.007 ↗
52. Additively manufactured CoCrFeNiMn high-entropy alloy via pre-alloyed powder10.1016/j.matdes.2018.107576 ↗
53. Direct laser deposited bulk CoCrFeNiNbx high entropy alloys10.1016/j.intermet.2019.106592 ↗
54. Formation of fully equiaxed grain microstructure in additively manufactured AlCoCrFeNiTi0. 5 high entropy alloy10.1016/j.matdes.2019.108202 ↗
55. The use of high-entropy alloys in additive manufacturing10.1016/j.scriptamat.2014.11.037 ↗
56. Engineering multi-scale B2 precipitation in a heterogeneous FCC based microstructure to enhance the mechanical properties of a Al0.5Co1.5CrFeNi1.5 high entropy alloy10.1016/j.jallcom.2020.154707 ↗
57. Multicomponent intermetallic nanoparticles and superb mechanical behaviors of complex alloys10.1126/science.aas8815 ↗
58. Tailoring heterogeneities in high-entropy alloys to promote strength–ductility synergy10.1038/s41467-019-13311-1 ↗
59. Metastable high-entropy dual-phase alloys overcome the strength–ductility trade-off10.1038/nature17981 ↗
60. The origin and stability of nanostructural hierarchy in crystalline solids10.1126/sciadv.aao6051 ↗
61. Modifying transformation pathways in high entropy alloys or complex concentrated alloys via thermo-mechanical processing10.1016/j.actamat.2018.05.009 ↗