journal article·2021-02Open access

Critical assessment of the impact of process parameters on vertical roughness and hardness of thin walls of AlSi10Mg processed by laser powder bed fusion

O. Poncelet, M. Marteleur, C. van der Rest, O. Rigo, J. Adrien, S. Dancette, P.J. Jacques, A. Simar

Abstract

Abstract This work deals with the impact of prominent process parameters in laser powder bed fusion (L-PBF) technique, also called selective laser melting (SLM), on relevant properties of AlSi10Mg such as surface roughness and hardness. More particularly, the influence of scanning strategies, track energy density (TED), and of the offset between the contours and the bulk hatching were scrutinized. Basic thin structures such as single wall tracks (SWT) and ultra thin walls (UTW) were used to isolate the effect of the TED and of the offset between parallel melt pool tracks on the vertical roughness, respectively. It is shown that the TED reduces the level of roughness mostly due to a geometrical effect. The optimum range of TED is shown to be at the beginning of the keyhole conditions, at the expense of the amount of sub-surface porosities and of hardness. Increasing the offset also allows reducing the roughness. Thicker structures with contours and bulk hatching were also used and brought the same conclusions. In this work, low levels of roughness (about 4 μm) have been obtained on vertical walls without any post-treatment but at the expense of the mechanical properties.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Additive Manufacturing Materials and Processes · Additive Manufacturing and 3D Printing Technologies · High Entropy Alloys Studies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (75)

Show source-provided references
1. Additive manufacturing of metallic components-process, structure and properties10.1016/j.pmatsci.2017.10.001 ↗
2. Improving the fatigue behaviour of a selectively laser melted aluminium alloy: influence of heat treatment and surface quality10.1016/j.matdes.2016.05.041 ↗
3. Fatigue properties of additively manufactured alsi10mg-surface treatment effect10.1016/j.prostr.2017.11.061 ↗
4. On the fatigue strength enhancement of additive manufactured alsi10mg parts by mechanical and thermal post-processing10.1016/j.matdes.2018.02.055 ↗
5. Fatigue properties and material characteristics of additively manufactured alsi10mg-effect of the contour parameter on the microstructure, density, residual stress, roughness and mechanical properties10.1016/j.ijfatigue.2018.08.023 ↗
6. Corrosion resistance of direct metal laser sintering alsimg alloy10.1002/sia.5981 ↗
7. Effect of surface roughness on corrosion fatigue performance of alsi10mg alloy produced by selective laser melting (slm)10.1016/j.matchar.2017.06.029 ↗
8. On microstructure and corrosion behaviour of alsi10mg alloy with low surface roughness fabricated by direct metal laser sintering10.1016/j.corsci.2019.05.032 ↗
9. Influence of process parameters on surface roughness of aluminum parts produced by dmls10.1007/s00170-012-4688-9 ↗
10. Experimental investigation on densification behavior and surface roughness of alsi10mg powders produced by selective laser melting10.1016/j.optlastec.2017.05.006 ↗
11. Thermal post-processing of alsi10mg parts produced by selective laser melting using recycled powder
12. Effect of selective laser melting process parameters on the quality of al alloy parts: powder characterization, density, surface roughness, and dimensional accuracy10.3390/ma11122343 ↗
13. Achieving low surface roughness alsi10mg_200c parts using direct metal laser sintering
14. Influence of re-melting on surface roughness and porosity of alsi10mg parts fabricated by selective laser melting10.1016/j.jallcom.2019.04.017 ↗
15. Arfan Majeed, Jingxiang Lv, Yingfeng Zhang, Muhammad Muzamil, Ali Waqas, Khalid Shamim, Muhammad Ejaz Qureshi, Fahad Zafar, An investigation into the influence of processing parameters on the surface quality of alsi10mg parts by slm process. In 2019 16th international bhurban conference on applied sciences and technology (IBCAST), 143–147.IEEE, 2019.10.1109/IBCAST.2019.8667175 ↗
16. Surface quality improvement by parameters analysis, optimization and heat treatment of alsi10mg parts manufactured by slm additive manufacturing
17. Research on surface roughness of alsi10mg parts fabricated by laser powder bed fusion10.3390/met8070524 ↗
18. The influence of process parameters on vertical surface roughness of the alsi10mg parts fabricated by selective laser melting10.1016/j.jmatprotec.2018.10.015 ↗
19. Statistical modelling and optimization of surface roughness in the selective laser sintering process10.1243/09544054JEM670 ↗
20. Roughness modeling of alsi10mg parts fabricated by selective laser melting10.1016/j.jmatprotec.2016.11.013 ↗
21. Investigation on selective laser melting alsi10mg cellular lattice strut: molten pool morphology, surface roughness and dimensional accuracy10.3390/ma11030392 ↗
22. On the surface quality of additive manufactured parts10.1007/s00170-016-9215-y ↗
23. Investigation of the accuracy and roughness in the laser powder bed fusion process10.1080/17452759.2018.1426368 ↗
24. Increasing the productivity of laser powder bed fusion: influence of the hull-bulk strategy on part quality, microstructure and mechanical performance of ti-6al-4v
25. Energy input effect on morphology and microstructure of selective laser melting single track from metallic powder10.1016/j.jmatprotec.2012.11.014 ↗
26. Processing alsi10mg by selective laser melting: parameter optimisation and material characterisation10.1179/1743284714Y.0000000702 ↗
27. On the formation of alsi10mg single tracks and layers in selective laser melting: microstructure and nano-mechanical properties10.1016/j.jmatprotec.2015.11.016 ↗
28. Selective laser melting of aluminium components10.1016/j.jmatprotec.2010.09.019 ↗
29. Fine-structured aluminium products with controllable texture by selective laser melting of pre-alloyed alsi10mg powder10.1016/j.actamat.2012.11.052 ↗
30. Reducing porosity in alsi10mg parts processed by selective laser melting
31. The alsi10mg samples produced by selective laser melting: single track, densification, microstructure and mechanical behavior10.1016/j.apsusc.2017.02.215 ↗
32. Manufacturing of thin wall structures in alsi10mg alloy by laser powder bed fusion through process parameters10.1016/j.jmatprotec.2018.01.029 ↗
33. In situ 3d x-ray microtomography of laser-based powder-bed fusion (l-pbf)-a feasibility study
34. Influence of structural features on processability, microstructures, chemical compositions, and hardness of selective laser melted complex thin-walled components10.1007/s00170-020-05773-1 ↗
35. Microstructure and mechanical properties of alsi10mg parts produced by the laser beam additive manufacturing (am) technology10.1007/s13632-014-0168-y ↗
36. Changes in the microstructure and mechanical properties of additively manufactured alsi10mg alloy after exposure to elevated temperatures10.1016/j.matchar.2018.01.028 ↗
37. Anisotropic mechanical behavior of alsi10mg parts produced by selective laser melting10.1007/s11837-016-2230-5 ↗
38. Gradient in microstructure and mechanical property of selective laser melted alsi10mg10.1016/j.jallcom.2017.11.020 ↗
39. Microstructure, precipitates and hardness of selectively laser melted alsi10mg alloy before and after heat treatment10.1016/j.matchar.2018.04.022 ↗
40. Mechanical properties of alsi10mg produced by selective laser melting10.1016/j.phpro.2012.10.059 ↗
41. The microstructure and mechanical properties of selectively laser melted alsi10mg: the effect of a conventional t6-like heat treatment10.1016/j.msea.2016.04.092 ↗
42. Selective laser melting of alsi10mg alloy: influence of heat treatment condition on mechanical properties and microstructure10.1007/s40194-018-0592-8 ↗
43. Effect of heat treatment on alsi10mg alloy fabricated by selective laser melting: microstructure evolution, mechanical properties and fracture mechanism10.1016/j.msea.2016.03.088 ↗
44. Single track formation in selective laser melting of metal powders10.1016/j.jmatprotec.2010.05.010 ↗
45. Physical aspects of process control in selective laser sintering of metals10.1002/adem.200310099 ↗
46. Mesoscopic simulation of selective beam melting processes10.1016/j.jmatprotec.2010.12.016 ↗
47. On the role of processing parameters in thermal behavior, surface morphology and accuracy during laser 3d printing of aluminum alloy10.1088/0022-3727/49/13/135501 ↗
48. Mesoscopic simulation model of selective laser melting of stainless steel powder10.1016/j.jmatprotec.2014.06.001 ↗
49. Laser powder-bed fusion additive manufacturing: physics of complex melt flow and formation mechanisms of pores, spatter, and denudation zones10.1016/j.actamat.2016.02.014 ↗
50. A novel method for the molten pool and porosity formation modelling in selective laser melting10.1016/j.ijheatmasstransfer.2019.06.038 ↗
51. Selective laser melting of alsi10mg alloy: process optimisation and mechanical properties development10.1016/j.matdes.2014.09.044 ↗
52. Selective laser melting of alsi10mg: influence of post-processing on the microstructural and tensile properties development10.1016/j.matdes.2016.05.066 ↗
53. Selective laser melting of iron-based powder10.1016/j.jmatprotec.2003.11.051 ↗
54. Direction and location dependency of selective laser melted alsi10mg specimens10.1016/j.jmatprotec.2016.11.029 ↗
55. Coherence scanning interferometry
56. Petzing · 2010
57. Surface texture metrology for metal additive manufacturing: a review10.1016/j.precisioneng.2016.06.001 ↗
58. Characterisation of the topography of metal additive surface features with different measurement technologies10.1088/1361-6501/aa7ce2 ↗
59. Topography of selectively laser melted surfaces: a comparison of different measurement methods10.1016/j.cirp.2017.04.075 ↗
60. Optimization of surface measurement for metal additive manufacturing using coherence scanning interferometry10.1117/1.OE.56.11.111714 ↗
61. In situ experiments with x ray tomography: an attractive tool for experimental mechanics10.1007/s11340-010-9333-7 ↗
62. In-situ x-ray tomographic monitoring of gypsum plaster setting10.1016/j.cemconres.2015.12.011 ↗
63. Fiji: an open-source platform for biological-image analysis10.1038/nmeth.2019 ↗
64. Observation of keyhole-mode laser melting in laser powder-bed fusion additive manufacturing10.1016/j.jmatprotec.2014.06.005 ↗
65. Effect of metal vaporization behavior on keyhole-mode surface morphology of selective laser melted composites using different protective atmospheres10.1016/j.apsusc.2015.07.044 ↗
66. Microstructural evolution and ebsd analysis of alsi10mg alloy fabricated by selective laser remelting10.1016/j.matchar.2019.110079 ↗
67. Strength and strain hardening of a selective laser melted alsi10mg alloy10.1016/j.scriptamat.2017.07.025 ↗
68. Effect of strut orientation on the microstructure heterogeneities in alsi10mg lattices processed by selective laser melting10.1016/j.scriptamat.2017.07.020 ↗
69. Heat treatment effect on the mechanical properties and fracture mechanism in alsi10mg fabricated by additive manufacturing selective laser melting process10.1016/j.msea.2018.05.074 ↗
70. Influence of the heat treatment on the microstructure and hardness of additively manufactured alsi10mg samples10.3139/147.110560 ↗
71. Surface morphology in selective laser melting of metal powders10.1016/j.phpro.2011.03.034 ↗
72. Prediction of lack-of-fusion porosity for powder bed fusion
73. Fundamental consolidation mechanisms during selective beam melting of powders10.1088/0965-0393/21/8/085011 ↗
74. Damage mechanisms in selective laser melted alsi10mg under as built and different post-treatment conditions10.1016/j.msea.2019.138210 ↗
75. Ductilisation and fatigue life enhancement of selective laser melted alsi10mg by friction stir processing10.1016/j.scriptamat.2019.05.044 ↗