High-temperature mechanical properties of AlSi10Mg specimens fabricated by additive manufacturing using selective laser melting technologies (AM-SLM)
Source abstract
Abstract
Abstract Mechanical properties (tensile strength and creep) of AlSi10Mg specimens fabricated by selective laser melting (SLM) in the Z-direction were investigated in the 25–400 °C temperature range. Specimens were tested after stress relief treatment. The results revealed that yield stress (YS) significantly decreases and the elongation increases at temperatures higher than 200 °C. The ultimate tensile stress (UTS) continuously decreases with temperature. The creep parameters, namely stress exponent n and apparent activation energy Q, were found to be 25 ± 2 and 146 ± 20 kJ/mole, respectively. It was shown that plastic deformation during creep is governed by dislocation movements in primary aluminum grains. The tested material is actually an aluminum composite reinforced by sub-micron Si particles. The creep resistance of AlSi10Mg alloy fabricated by selective laser melting is close to that for aluminum matrix particles reinforced composites.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Additive Manufacturing Materials and Processes · Additive Manufacturing and 3D Printing Technologies · High Entropy Alloys Studies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (40)
Show source-provided references
1. Creep behavior of Al-Si die-cast alloys
2. High temperature creep behavior of metal matrix aluminum-SiC composites10.1016/0956-7151(93)90094-9 ↗
3. An evaluation of the creep properties of Two Al-Si alloys produced by Rapid solidification processing10.1007/BF02595636 ↗
4. Constitutive equations for Hot deformation of an Al-6061/20%Al2O3 composite10.1016/S0921-5093(01)01071-1 ↗
5. Creep strengthening in a discontinuous SiC-Al composite10.1007/BF02669441 ↗
6. Effect of a solid solution on the steady-State creep behavior of an aluminum matrix composite10.1007/BF02648408 ↗
7. Zamani · 2015
8. Overview of aluminum alloy mechanical properties during and after fires
9. Mechanical properties of AlSi10Mg produced by selective laser melting10.1016/j.phpro.2012.10.059 ↗
10. Strain rate sensitivity and fracture mechanism of AlSi10Mg parts produced by selective laser melting10.1016/j.msea.2016.11.070 ↗
11. High temperature material properties of IN738LC processed by selective laser melting (SLM) technology10.1108/13552541311323281 ↗
12. Inclusions, porosity, and fatigue of AlSi10Mg parts produced by selective laser melting
13. Anisotropic mechanical behavior of AlSi10Mg parts produced by selective laser melting10.1007/s11837-016-2230-5 ↗
14. Direction and location dependency of selective laser melted AlSi10Mg specimens10.1016/j.jmatprotec.2016.11.029 ↗
15. Selective laser melting of AlSi10Mg alloy: process optimization and mechanical properties development10.1016/j.matdes.2014.09.044 ↗
16. On the effect of shot-peening on fatigue resistance of AlSi10Mg specimens fabricated by additive manufacturing using selective laser melting (AM-SLM)
17. Selective laser melting of AlSi10Mg alloy: influence of heat treatment condition on mechanical properties and microstructure10.1007/s40194-018-0592-8 ↗
18. Fatigue of AlSi10Mg specimens fabricated by additive manufacturing selective laser melting (AM-SLM)10.1016/j.msea.2017.08.027 ↗
19. ASTM B557M-15 · 2016
20. ASTM E8/E8M · 2009 · 1
21. Dynamic response of AlSi10Mg alloy by selective laser melting10.1016/j.msea.2017.02.004 ↗
22. Nondestructive ultrasonic evaluation of additively manufactured AlSi10Mg samples
23. Tensile, fatigue and creep properties of aluminum heat exchanger tube alloys for temperatures from 293 K to 573 K (20°C to 300°C)10.1007/s11661-013-2003-5 ↗
24. Mechanism based creep model incorporating damage10.1115/1.4000822 ↗
25. McGill university montreal
26. Compression creep of PM aluminum matrix composites reinforced with SiC short fibres10.1016/j.msea.2005.11.035 ↗
27. Macro- and microstructural characterization of cup-shaped AlSi10Mg components fabricated by selective laser melting (SLM)10.1007/s13632-016-0305-x ↗
28. Quantitative characterization of hypoeutectic Aluminum–Silicon–Copper As-cast alloy microstructures10.1520/MPC20160025 ↗
29. Creep rupture of a silicon carbide reinforced aluminum composite10.1007/BF02644396 ↗
30. Analysis of the creep behavior of silicon carbide whisker reinforced 2124 Al (T4)10.1007/BF02646227 ↗
31. Hasegawa · 1990 · 159
32. Microstructure and strength of selectively laser melted AlSi10Mg10.1016/j.actamat.2016.07.012 ↗
33. Fine-structured aluminium products with controllable texture by selective laser melting of pre-alloyed AlSi10Mg powder10.1016/j.actamat.2012.11.052 ↗
34. Evolution of microstructure in laser deposited Al–11.28%Si alloy10.1016/j.surfcoat.2011.09.051 ↗
35. LEDS: properties and effects of Low energy dislocation structures10.1016/0025-5416(87)90442-3 ↗
36. Structure and strength of lath martensite10.1007/BF02465797 ↗
37. Grain structure and dislocation density measurements in a friction-stir welded aluminum alloy using X-ray peak profile analysis10.1016/j.msea.2008.08.007 ↗
38. Kundu · 2007
39. Phase and grain size inhomogeneity and their influences on creep behavior of Co–Cr–Mo alloy additive manufactured by electron beam melting10.1016/j.actamat.2014.11.012 ↗
40. Effect of thermally induced porosity on an as-HIP powder metallurgy superalloy. NASA technical memorandum