journal article·2022-10

Characterizing the separation behavior of photocurable PDMS on a hydrogel film during vat photopolymerization: A benchmark study

Feimo Yang, Aamer Kazi, Alec Marmo, Melissa A. Grunlan, Bruce L. Tai

Publisher page

Abstract

The separation between printed part and vat floor in constrained surface vat photopolymerization (VP) is a long-standing challenge, which limits the printability of soft materials like polydimethylsiloxane (PDMS). This study aims to characterize the separation behavior of a photocurable PDMS resin on a hydrogel film whose high-water content is expected to minimize the separation force. For this benchmark study, a commercially available polytetrafluoroethylene (PTFE) and an acrylate-based photopolymer are used as the baselines. Along with two printing speeds, a total of eight cases (two films, two resins, and two speeds) are used in the design of the experiment. A modified digital light processing (DLP) printing with a built-in force sensor is used to sample the force profile during the printing. The results show that PDMS has a lower separation force but longer separation distance than those of the acrylate-based resin. The hydrogel film can further minimize the separation force and distance; those values are under 0.5 N in PDMS printing. A lower speed can further reduce the separation force, but increase separation distance, likely due to the rate-dependent material properties. These results suggest a potential solution to print PDMS fast with small and fragile features.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Additive Manufacturing and 3D Printing Technologies · Photopolymerization techniques and applications · Advanced Sensor and Energy Harvesting Materials

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (30)

Show source-provided references
1. Vat photopolymerization of polymers and polymer composites: processes and applications
2. Prediction of the deformed geometry of vat photo-polymerized components using a multi-physical modeling framework
3. Digital material fabrication using mas‹ imag… projection based stereolithography10.1108/13552541311312148 ↗
4. A review of vat photopolymerization technology: materials, applications, challenges, and future trends of 3D printing10.3390/polym13040598 ↗
5. A review on stereolithography and its applications in biomedical engineering10.1016/j.biomaterials.2010.04.050 ↗
6. Study of separation force in constrained surface projection stereolithography10.1108/RPJ-12-2015-0188 ↗
7. Effects of surface energy reducing agents on adhesion force in liquid bridge microstereolithography
8. Oxygen-controlled bottom-up mask-projection stereolithography for ceramic 3D printing10.1016/j.ceramint.2017.08.014 ↗
9. C. Schmidleithner, D.M. Kalaskar, Stereolithography, IntechOpen 2018.10.5772/intechopen.78147 ↗
10. A vibration-assisted method to reduce separation force for stereolithography10.1016/j.jmapro.2018.03.052 ↗
11. Development of a variable tensioning system to reduce separation force in large scale stereolithography
12. Low adhesion continuous constrained-surface projection stereolithography process based on curing degree control
13. Mechanical isotropy and postcure shrinkage of polydimethylsiloxane printed with digital light processing10.1108/RPJ-10-2019-0255 ↗
14. 3D printing of a polydimethylsiloxane/polytetrafluoroethylene composite elastomer and its application in a triboelectric nanogenerator10.1021/acsami.0c18201 ↗
15. 3D printing PDMS elastomer in a hydrophilic support bath via freeform reversible embedding10.1021/acsbiomaterials.6b00170 ↗
16. 3D printed multifunctional, hyperelastic silicone rubber foam10.1002/adfm.201900469 ↗
17. Bound rubber and crepe hardenin‡ in silicone rubber10.1002/app.1977.070211203 ↗
18. Material Safety Data Sheet – SUPERFINE UV RESIN_CLEAR 500G×2, in: X. inc. (Ed.) 2017.
19. Feasibility study of silicone stereolithography with an optically created dead zone
20. FlexiForceTM standard Model A101, in: T. inc. (Ed.) 2021.
21. Y.-C. Chang, T.-H. Kuo, Stereolithography Elastic Film With Adjustable Peeling Force, U.S. Patent Application Publication, XYZPRINTING, INC., New Taipei City ( TW); KINPO ELECTRONICS, INC., New Taipei City ( TW), United States, 2019.
22. On-line force monitoring of platform ascending rapid prototyping system10.1016/j.jmatprotec.2004.05.015 ↗
23. Investigation of separation force for constrained-surface stereolithography process from mechanics perspective10.1108/RPJ-06-2016-0091 ↗
24. Effect of constrained surface texturing on separation force in projection stereolithography10.1115/1.4040322 ↗
25. Study on the surface energy characteristics of polydimethylsiloxane (PDMS) films modified by C4F8/O2/Ar plasma treatment10.1016/j.apsusc.2017.11.009 ↗
26. A flexible and wearable glucose sensor based on functional polymers with soft-MEMS techniques10.1016/j.bios.2006.05.006 ↗
27. Effect of film thickness on the changes in gas permeability of a glassy polyarylate due to physical agingPart I. Experimental observations10.1016/S0032-3861(99)00172-X ↗
28. Elastic modulus and flexural strength comparisons of high-impact and traditional denture base acrylic resins10.1016/j.sdentj.2013.12.005 ↗
29. Rapid digital light 3D printing enabled by a soft and deformable hydrogel separation interface10.1038/s41467-021-26386-6 ↗
30. Measuring UV curing parameters of commercial photopolymers used in additive manufacturing