journal article·2012-07

Microstructural study of surface melted and chromium surface alloyed ductile iron

M. Heydarzadeh Sohi, M. Ebrahimi, H.M. Ghasemi, A. Shahripour

Applied Surface Science· Volume 258· Issue 19
Publisher page

Abstract

Abstract In this study, ductile iron was surface melted and chromium surface alloyed via pre-placing of ferrochromium powder with different thicknesses and subsequently surface melting by tungsten inert gas (TIG) process. Optical and scanning electron microscopy, as well as micro-hardness testing and X-ray diffraction analysis were used for characterization of the treated samples. Surface melting and chromium surface alloying resulted in formation of ledeburitic structure and high chromium white cast iron in the treated layers, respectively. It was also noticed that hardness of the treated layers was considerably higher than that of the base material. Increasing thickness of ferrochromium layer increased the amount of M7C3 carbides and hardness of the alloyed layer.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Metal Alloys Wear and Properties · Metal and Thin Film Mechanics · High Entropy Alloys Studies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (17)

Show source-provided references
1. Continuously cast ductile iron: processing, structures, and properties10.1016/j.jmatprotec.2011.03.008 ↗
2. Microstructure and wear resistance of composite layers on a ductile iron with multicarbide by laser surface alloying10.1016/j.apsusc.2010.05.015 ↗
3. Effect of surface alloying on microstructure and wear behavior of ductile iron surface-modified with a nickel based alloy using shielded metal arc welding10.1016/j.matdes.2010.10.006 ↗
4. Microstructure evolution during surface alloying of ductile iron and austempered ductile iron by electron beam melting10.1016/j.apsusc.2009.06.011 ↗
5. Surface melting of nodular cast iron by Nd–YAG laser and TIG10.1016/j.jmatprotec.2005.04.108 ↗
6. In situ synthesis of SiC reinforced MMC surface on AISI 304 stainless steel by TIG surface alloying10.1016/j.surfcoat.2005.02.178 ↗
7. Effects of surface alloying on microstructure and wear behavior of ductile iron10.1016/j.matdes.2010.01.017 ↗
8. Surface hardening of a ductile cast iron roll using high energy electron beams10.1007/s11661-997-0212-5 ↗
9. Comparison of the influence of molybdenum and chromium TIG surface alloying on the microstructure, hardness and wear resistance of ADI10.1016/j.jmatprotec.2007.11.157 ↗
10. Tungsten-inert gas surface alloying of a low carbon steel10.1016/S0257-8972(01)01712-1 ↗
11. Wear behavior of gas tungsten arc deposited FeCrC FeCrSi, and WCo coatings on AISI 1018 steel10.1016/j.surfcoat.2004.08.227 ↗
12. Microstructure and hardness studies of electron beam melted surface of mild steel10.1016/j.apsusc.2009.02.077 ↗
13. Laser surface engineering to improve wear resistance of austempered ductile iron10.1016/S0921-5093(00)01253-3 ↗
14. A new experimental technique for measuring strain and residual stresses during a laser remelting process10.1016/j.jmatprotec.2004.01.007 ↗
15. Development of a laser surface melting process for improvement of the wear resistance of gray cast iron10.1016/0043-1648(83)90169-2 ↗
16. Microstructure and stability of Fe–Cr–C hard facing alloys10.1016/0921-5093(90)90085-H ↗
17. Comparison of measured and calculated thickness of martensite and ledeburite shells around graphite nodules in the hardened layer of nodular iron after laser surface remelting10.1016/S0169-4332(01)00823-6 ↗