Detectability by X-ray micro computed tomography of fatigue initiating void defects in laser powder-bed additively manufactured Ti-6Al-4V coupons
Source abstract
Abstract
Non-destructive inspection is important for the quality assurance of additively manufactured components. In this study, X-ray micro Computed Tomography (µCT) was assessed for its capabilities and limitations to detect fatigue-initiation porosities in Ti-6Al-4V additively manufactured coupons. Cylindrical coupons were built using laser powder-bed fusion (L-PBF) from three different vendors and four different L-PBF machines that utilized their default process parameters. Using OEM prescribed default process parameters, there was significant variability in the defect distribution between machine to machine and also coupon to coupon that was on the same build plate, primarily due the difference in the internal quality assurance procedures and scan strategies adopted by each vendor. The probability of detection for conventional µCT (cubic voxel size 17.77 µm) was investigated by comparing with what was detected using a Synchrotron Radiation Micro Computed Tomography (SRµCT) at cubic voxel size 5.91 µm. It was found that µCT’s detectability relative to SRµCT was approximately 90% for defect diameters of the circumscribed sphere of 230 µm and above and 100% for diameters of 340 µm and above (12–14 times the voxel size of the µCT scan). The type of defect was a key factor to the detectability of large sized defects (>200 µm in diameter) due to the flatness and elongated shape factors. Fatigue results showed the critical defect √Area at the surface was approximately 100 µm at 500 MPa stress level, where significant scatter in fatigue life was observed. Post-fatigue test fractography identified different types of fatigue initiating defects, of which a ‘flat’ lack-of-fusion type defect was undetectable by either µCT or SRµCT. This type of defect was extremely flat and occupied very little spatial resolution through the build direction which limited the detection by automated threshold-based defect detection algorithms.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Additive Manufacturing Materials and Processes · Advanced X-ray and CT Imaging · Welding Techniques and Residual Stresses
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (52)
Show source-provided references
1. Additively manufactured Ti-6Al-4V replacement parts for military aircraft10.1016/j.ijfatigue.2019.02.041 ↗
2. Defects in metal additive manufacturing processes10.1007/s11665-021-05919-6 ↗
3. Processing parameters in laser powder bed fusion metal additive manufacturing10.1016/j.matdes.2020.108762 ↗
4. Effects of process parameters on porosity in laser powder bed fusion revealed by X-ray tomography
5. Influence of defects on mechanical properties of Ti–6Al–4V components produced by selective laser melting and electron beam melting10.1016/j.matdes.2015.07.147 ↗
6. Fatigue of additive manufactured Ti-6Al-4V, Part I: The effects of powder feedstock, manufacturing, and post-process conditions on the resulting microstructure and defects10.1016/j.ijfatigue.2019.105358 ↗
7. Correlation between porosity and processing parameters in TiAl6V4 produced by selective laser melting10.1016/j.matdes.2016.05.070 ↗
8. On the role of volumetric energy density in the microstructure and mechanical properties of laser powder bed fusion Ti-6Al-4V alloy
9. Defects in additive manufactured metals and their effect on fatigue performance: a state-of-the-art review10.1016/j.pmatsci.2020.100724 ↗
10. Feature-based volumetric defect classification in metal additive manufacturing10.1038/s41467-022-34122-x ↗
11. Keyhole-induced porosities in Laser-based Powder Bed Fusion (L-PBF) of Ti6Al4V: high-fidelity modelling and experimental validation
12. Detecting keyhole pore defects and monitoring process signatures during laser powder bed fusion: a correlation between in situ pyrometry and ex situ X-ray radiography
13. Controlling process instability for defect lean metal additive manufacturing10.1038/s41467-022-28649-2 ↗
14. Defect structure process maps for laser powder bed fusion additive manufacturing
15. Types of spatter and their features and formation mechanisms in laser powder bed fusion additive manufacturing process
16. Spatter formation in selective laser melting process using multi-laser technology10.1016/j.matdes.2017.06.040 ↗
17. A novel image feature descriptor for SLM spattering pattern classification using a consumable camera10.1007/s00170-020-05995-3 ↗
18. Fatigue performance of laser additive manufactured Ti–6Al–4V in very high cycle fatigue regime up to 109 cycles10.3389/fmats.2015.00072 ↗
19. Fatigue behaviour of additively manufactured Ti-6Al-4V alloy: the role of defects on scatter and statistical size effect10.1016/j.ijfatigue.2020.105811 ↗
20. Critical assessment of the fatigue performance of additively manufactured Ti–6Al–4V and perspective for future research10.1016/j.ijfatigue.2015.12.003 ↗
21. Analysis of the effect of internal defects on fatigue performance of additive manufactured metals10.1016/j.msea.2020.139385 ↗
22. Effects of defects on mechanical properties in metal additive manufacturing: a review focusing on X-ray tomography insights10.1016/j.matdes.2019.108385 ↗
23. Defect characteristics and analysis of their variability in metal L-PBF additive manufacturing10.1016/j.matdes.2019.108091 ↗
24. Quantification and characterisation of porosity in selectively laser melted Al–Si10–Mg using X-ray computed tomography10.1016/j.matchar.2015.12.001 ↗
25. Analyzing the effects of powder and post-processing on porosity and properties of electron beam melted Ti-6Al-4V10.1080/21663831.2017.1340911 ↗
26. Defect-based analysis of the laser powder bed fusion process using X-ray data10.1007/s00170-022-10407-9 ↗
27. Fatigue from defect: influence of size, type, position, morphology and loading10.1016/j.ijfatigue.2021.106531 ↗
28. A comparison of fatigue strength sensitivity to defects for materials manufactured by AM or traditional processes10.1016/j.ijfatigue.2016.06.020 ↗
29. Qualification of AM parts: extreme value statistics applied to tomographic measurements10.1016/j.matdes.2017.05.091 ↗
30. X-ray microcomputed tomography in additive manufacturing: a review of the current technology and applications10.1089/3dp.2018.0060 ↗
31. Standardized X-ray tomography testing of additively manufactured parts: a round robin test
32. Intentionally seeding pores in additively manufactured alloy 718: process parameters, microstructure, defects, and fatigue
33. Measurement of small defect testing accuracy in additive manufacturing alloy using industrial CT method
34. ASTM F3301–18a: Standard of Additive manufacturing - Post processing methods - Stardard specification for thermal post processing metal parts made via powder bed fusion. 2018. ASTM International. West Conshohocken, PA. https://doi.org/10.1520/F3301–18A.10.1520/F3301-18A ↗
35. ASTM E466-15 · 2015
36. Influence of defects, surface roughness and HIP on the fatigue strength of Ti-6Al-4V manufactured by additive manufacturing10.1016/j.ijfatigue.2018.07.020 ↗
37. Fatigue of additive manufactured Ti-6Al-4V, Part II: the relationship between microstructure, material cyclic properties, and component performance10.1016/j.ijfatigue.2019.105363 ↗
38. Effects of defects, inclusions and inhomogeneities on fatigue strength10.1016/0142-1123(94)90001-9 ↗
39. Space-filling X-ray source trajectories for efficient scanning in large-angle cone-beam computed tomography10.1109/TCI.2018.2841202 ↗
40. Influence of resolution on the X-ray CT-based measurements of metallic AM lattice structures10.1007/s40194-020-00920-4 ↗
41. Rapidly converging multigrid reconstruction of cone-beam tomographic data10.1117/12.2238267 ↗
42. Quantitative characterization of the X-ray beam at the Australian Synchrotron Imaging and Medical Beamline (IMBL)10.1107/S1600577516015563 ↗
43. Toolbox for advanced X-ray image processing
44. Volume, shape, and roundness of rock particles10.1086/623964 ↗
45. Flaw identification in additively manufactured parts using X-ray computed tomography and destructive serial sectioning10.1007/s11665-021-05567-w ↗
46. The effect of manufacturing defects on the fatigue behaviour of Ti-6Al-4V specimens fabricated using selective laser melting
47. NASA-STD-6030: Additive Manufacturing requirements for spaceflight system. 2021. National Aeronautics and Space Administration. 〈https://standards.nasa.gov/standard/NASA/NASA-STD-6030〉.
48. ASTM F2924-14R21 · 2014
49. Effects of building orientation and heat treatment on fatigue behavior of selective laser melted 17-4 PH stainless steel10.1016/j.ijfatigue.2016.03.014 ↗
50. Effect of heat treatments on pore morphology and microstructure of laser additive manufactured parts
51. Fatigue properties of a titanium alloy (Ti–6Al–4V) fabricated via electron beam melting (EBM): Effects of internal defects and residual stress10.1016/j.ijfatigue.2016.04.022 ↗
52. Fatigue life of additively manufactured Ti–6Al–4V in the very high cycle fatigue regime10.1016/j.ijfatigue.2016.05.018 ↗