journal article·2019-03Open access

Hygromechanical properties of 3D printed continuous carbon and glass fibre reinforced polyamide composite for outdoor structural applications

G. Chabaud, M. Castro, C. Denoual, A. Le Duigou

Abstract

Abstract The additive manufacturing of structural composites is a disruptive technology currently limited by its moderate mechanical properties. Continuous fibre reinforcements have recently been developed to create high performance composites and open up encouraging prospects. However, to increase their use, deeper understanding of the relationship between process and induced properties remains necessary. In addition, to apply these materials to engineering applications, it is of high importance to evaluate the effect of environmental conditions on their mechanical performances, particularly when moisture-sensitive polymer is used (PolyAmide PA for instance) which is currently lacking in the literature. This present article aims to investigate in more detail the relationship between the process, the mechanical behaviour and the induced properties of continuous carbon and glass fibres reinforced with a polyamide matrix manufactured using a commercial 3D printer. In addition, their hygromechanical behaviour linked to moisture effect is investigated through sorption, hygroexpansion and mechanical properties characterization on a wide range of relative humidity (10–98% Relative Humidity RH). The printing process induces an original microstructure with multiscale singularities (intra/inter beads porosity and filament loop). Longitudinal tensile performance shows that the reinforcing mechanism is typical of composite laminates for glass and carbon. However, the rather poor transverse properties are not well fitted by the Rule Of Mixture (ROM), thus underlining the specificity of the printing-induced microstructure and an anisotropic behaviour in the material. Non-negligible (5–6%) moisture uptake is observed at 98% RH, as well as orthotropic hygroscopic expansion of PA/carbon and PA/glass composites. The consequences of various moisture contents on mechanical properties are studied, showing a reduction of PA/carbon stiffness and strength of 25 and 18% in the longitudinal direction and 45 and 70% in the transverse direction. For PA/glass composites, we obtain a reduction in strength of 25% in the longitudinal direction, along with a 80% reduction of stiffness and 45% in strength in the transverse direction. A wetting/drying cycle underlines reversible phenomena in the longitudinal direction and mainly non-reversible degradation in the transverse direction.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Additive Manufacturing and 3D Printing Technologies · Innovations in Concrete and Construction Materials · Manufacturing Process and Optimization

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (48)

Show source-provided references
1. 3D printing: the dawn of a new era in manufacturing?10.1108/AA-06-2013-055 ↗
2. Crump · 1992
3. A review on additive manufacturing of polymer-fiber composites10.1016/j.compstruct.2017.08.088 ↗
4. 3D printing of polymer matrix composites: a review and prospective10.1016/j.compositesb.2016.11.034 ↗
5. Additive manufacturing (3D printing): a review of materials, methods, applications and challenges10.1016/j.compositesb.2018.02.012 ↗
6. Fused fi lament fabrication of fi ber-reinforced polymers : a review
7. 3-D printing: the new industrial revolution10.1016/j.bushor.2011.11.003 ↗
8. https://www.stratasys.com (Accessed May 2018) n.d.:2–3.
9. https://www.markforged.com/materials/ (Accessed May 2018) n.d.
10. Highly oriented carbon fiber-polymer composites via additive manufacturing10.1016/j.compscitech.2014.10.009 ↗
11. Additive manufacturing of carbon fiber reinforced thermoplastic composites using fused deposition modeling10.1016/j.compositesb.2015.06.013 ↗
12. Experimental characterization and micrography of 3D printed PLA and PLA reinforced with short carbon fibers10.1016/j.compositesb.2017.05.013 ↗
13. Properties of oriented carbon fiber/polyamide 12 composite parts fabricated by fused deposition modeling10.1016/j.matdes.2017.11.027 ↗
14. Short fiber reinforced composites for fused deposition modeling10.1016/S0921-5093(00)01810-4 ↗
15. Three-dimensional printing of continuous-fiber composites by in-nozzle impregnation10.1038/srep23058 ↗
16. Interface and performance of 3D printed continuous carbon fiber reinforced PLA composites10.1016/j.compositesa.2016.05.032 ↗
17. Fiber line optimization in single ply for 3D printed composites
18. 3D printing for continuous fiber reinforced thermoplastic composites : mechanism and performance10.1108/RPJ-08-2015-0098 ↗
19. Fabrication and mechanical characterization of continuous carbon fiber-reinforced thermoplastic using a preform by three-dimensional printing and via hot-press molding
20. 3D printed continuous fibre reinforced composite corrugated structure
21. Characterization of mechanical properties and fracture mode of additively manufactured carbon fiber and glass fiber reinforced thermoplastics10.1016/j.matdes.2017.10.021 ↗
22. 3D printing of continuous carbon fibre reinforced thermo-plastic (CFRTP) tensile test specimens
23. Characterization of 3D printed long fibre reinforced composites
24. Fabrication of continuous carbon, glass and Kevlar fibre reinforced polymer composites using additive manufacturing
25. Effect of sea water and humidity on the tensile and compressive properties of carbon-polyamide 6 laminates10.1016/j.compositesa.2016.10.012 ↗
26. Characterization of sea water ageing effects on mechanical properties of Carbon/Epoxy composites for tidal turbine blades10.1016/j.compositesa.2015.08.035 ↗
27. Isothermal phase behavior of nylon-6,-66, and -610 polyamides in formic acid water systems10.1002/polb.1994.090320706 ↗
28. Effect of flax fibres individualisation on tensile failure of flax/epoxy unidirectional composite10.1016/j.compositesa.2013.03.018 ↗
29. Anisotropic material properties of fused deposition modeling ABS10.1108/13552540210441166 ↗
30. Effects of build orientations on tensile properties of PLA material processed by FDM10.4028/www.scientific.net/AMR.1044-1045.31 ↗
31. The mechanical properties of cellular solids10.1007/BF02645546 ↗
32. Effects of cure cycle pressure and voids on some mechanical properties of carbon/epoxy laminates10.1016/0010-4361(95)96808-J ↗
33. Effects of cure cycles on void content and mechanical properties of composite laminates10.1016/j.compstruct.2005.02.001 ↗
34. Influence of voids on the tensile performance of carbon/epoxy fabric laminates10.1016/S1005-0302(11)60028-5 ↗
35. Effect of voids on failure mechanisms in RTM laminates10.1016/0266-3538(95)00024-0 ↗
36. Failure surface of epoxy-modified fiber-reinforced composites under transverse tension and out-of-plane shear10.1016/j.ijsolstr.2009.01.014 ↗
37. Transverse properties of carbon fibres by nano-indentation and micro-mechanics10.1007/s10443-008-9057-3 ↗
38. Transport principles—solution, diffusion and permeation in polymer membranes
39. Moisture sorption in polyamide 6.6: experimental investigation and comparison to four physical-based models10.1016/j.polymertesting.2015.02.004 ↗
40. Mark · 1990 · vol. 11
41. Swelling of glass-fiber reinforced polyamide 66 during conditioning in water, ethylene glycol and antifreeze mixture
42. Characterization of hygroscopic swelling behavior of mold compounds and plastic packages10.1109/TCAPT.2004.831777 ↗
43. Effect of moisture absorption on the mechanical behavior of carbon fiber/epoxy matrix composites10.1007/s10853-012-6947-4 ↗
44. A method to measure the influence of humidity and temperature on the interfacial adhesion in polyamide composites10.1080/09276440.2015.1059114 ↗
45. Structure and mechanical behavior of big area additive manufacturing (BAAM) materials10.1108/RPJ-12-2015-0183 ↗
46. Experimental characterization and micrography of 3D printed PLA and PLA reinforced with short carbon fibers Experimental characterization and micrography of 3D printed10.1016/j.compositesb.2017.05.013 ↗
47. Properties of Wrought Aluminum and Aluminum Alloys. ASM Handbook, Vol 2 Prop Sel Nonferrous Alloy Spec Mater n.d.;2:62–122. doi:https://doi.org/10.1361/asmhba000.
48. Mechanical behavior of carbon fiber reinforced polyamide composites10.1016/S0266-3538(03)00119-2 ↗