Optimization and comparison of porosity rate measurement methods of Selective Laser Melted metallic parts
Source abstract
Abstract
The systematic occurrence of porosities inside selective laser melted (SLM) parts is a well-known phenomenon. In order to improve the density of SLM parts, it is important not only to assess the physical origin of the different types of porosities, but also to be able to measure as precisely as possible the porosity rate so that one may select the optimum manufacturing parameters. Considering 316 L steel parts built with different input energies, the current paper aims to (1) present the different types of porosities generated by SLM and their origins, (2) compare different methods for measuring parts density and (3) propose optimal procedures. After a preliminary optimization step, three methods were used for quantifying porosity rate: the Archimedes method, the helium pycnometry and micrographic observations. The Archimedes method shows that results depend on the nature and temperature of the fluid, but also on the sample volume and its surface roughness. During the micrographic observations, it has been shown that the results depend on the magnification used and the number of micrographs considered. A comparison of the three methods showed that the optimized Archimedes method and the helium pycnometry technique gave similar results, whereas optimized micrographic observations systematically underestimated the porosity rate. In a second step, samples were analyzed to illustrate the physical phenomena involved in the generation of porosities. It was confirmed that: (1) low Volume Energy Density (VED) causes non-spherical porosities due to insufficient fusion, (2) in intermediary VED the small amount of remaining blowhole porosities come from gas occlusion in the melt-pool and (3) in excessive VED, cavities are formed due to the key-hole welding mode.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Additive Manufacturing Materials and Processes · Welding Techniques and Residual Stresses · Additive Manufacturing and 3D Printing Technologies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (41)
Show source-provided references
1. Powder bed binder jet 3D printing of Inconel 718: densification, microstructural evolution and challenges10.1016/j.cossms.2016.12.002 ↗
2. Additive manufacturing of metals: a review
3. Metallic additive manufacturing: state-of-the-art review and prospects10.1051/meca/2012003 ↗
4. EPMA · 2015 · 28
5. Additive manufacturing of metals10.1016/j.actamat.2016.07.019 ↗
6. The metallurgy and processing science of metal additive manufacturing10.1080/09506608.2015.1116649 ↗
7. Additive manufacturing of metallic components – process, structure and properties10.1016/j.pmatsci.2017.10.001 ↗
8. Multiaxial fatigue behavior of wrought and additive manufactured Ti-6Al-4V including surface finish effect10.1016/j.ijfatigue.2017.03.044 ↗
9. Reduction of the residual porosity in parts manufactured by selective laser melting using skywriting and high focus offset strategies10.1016/j.phpro.2016.08.090 ↗
10. Mechanisms and characteristics of spatter generation in SLM processing and its effect on the properties10.1016/j.matdes.2016.12.060 ↗
11. Experimental analysis of spatter generation and melt-pool behavior during the powder bed laser beam melting process10.1016/j.jmatprotec.2017.08.012 ↗
12. Influence of process parameters on the quality of aluminium alloy en AW 7075 using Selective Laser Melting (SLM)10.1016/j.phpro.2016.08.096 ↗
13. Influences of energy density on porosity and microstructure of selective laser melted 17-4PH stainless steel
14. Capabilities and performances of the selective laser melting process
15. Densiication behavior of 316L stainless steel parts fabricated by selective laser melting by variation in laser energy density10.2320/matertrans.M2016284 ↗
16. Correlation between porosity and processing parameters in TiAl6V4 produced by selective laser melting10.1016/j.matdes.2016.05.070 ↗
17. Densification behavior of gas and water atomized 316L stainless steel powder during selective laser melting10.1016/j.apsusc.2010.02.030 ↗
18. Texture control of 316L parts by modulation of the melt pool morphology in selective laser melting10.1016/j.jmatprotec.2018.08.049 ↗
19. Analysis of laser–melt pool–powder bed interaction during the selective laser melting of a stainless steel10.2351/1.4983259 ↗
20. A study on the effect of energy input on spatter particles creation during selective laser melting process
21. Denudation of metal powder layers in laser powder bed fusion processes10.1016/j.actamat.2016.05.017 ↗
22. Prediction of lack-of-fusion porosity for powder bed fusion
23. Steen · 2010
24. Selective laser melting of Al7050 powder: Melting mode transition and comparison of the characteristics between the keyhole and conduction mode10.1016/j.matdes.2017.09.014 ↗
25. Melt pool and keyhole behaviour analysis for deep penetration laser welding10.1088/0022-3727/43/44/445501 ↗
26. Microstructural and texture development in direct laser fabricated IN71810.1016/j.matchar.2013.12.012 ↗
27. Comparison of density of stainless steel 316L parts produced with selective laser melting using different powder grades, Solid Free
28. Comparison of density measurement techniques for additive manufactured metallic parts10.1108/13552541111156504 ↗
29. Porosity testing methods for the quality assessment of selective laser melted parts10.1016/j.cirp.2016.04.054 ↗
30. Scanning optical microscopy for porosity quantification of additively manufactured components
31. ASTM International · 2013 · B311
32. Encyclopedic dictionary of polymers
33. OIML · 2019
34. Lotus effect in wetting and self-cleaning10.1016/j.biotri.2015.08.002 ↗
35. A numerical investigation on the physical mechanisms of single track defects in selective laser melting10.1016/j.ijheatmasstransfer.2018.06.073 ↗
36. Printability of alloys for additive manufacturing10.1038/srep19717 ↗
37. Numerical simulation of multi-component evaporation during selective electron beam melting of TiAl10.1016/j.jmatprotec.2017.04.016 ↗
38. 2019
39. Caveat on the use of the Delesse principle of areal analysis forestimating component volume densities10.1111/j.1365-2818.1974.tb03979.x ↗
40. Metallographic techniques for tool steels
41. Oxides, porosity and fatigue performance of AlSi10Mg parts produced by selective laser melting10.1016/j.ijfatigue.2016.06.002 ↗