Experimentally-validated orthotropic elastic model for Wire-and-Arc Additively Manufactured stainless steel
Source abstract
Abstract
Abstract Wire-and-Arc Additively Manufactured (WAAM) alloys are characterized by specific mechanical properties which can largely differ from the conventionally-manufactured alloys. In detail, the printing process results in a peculiar microstructure, characterized by preferential crystallographic orientation with reference to the printing direction, that leads to an anisotropic mechanical behavior of the printed part. Previous experimental tests on WAAM-produced stainless steel plates showed in particular a strong anisotropic elastic behavior. Based on the above, the present work formulates a specific anisotropic elastic model for a WAAM-processed austenitic stainless steel, considering an orthogonally anisotropic (or orthotropic) constitutive law and a procedure to calibrate the elastic parameters based on the experimental results. In detail, the procedure is applied to calibrate the numerical values of the elastic parameters of a specific WAAM 304L austenitic stainless steel. For this aim, specific investigations on both the mechanical and microstructural features were carried out. Experimental tensile tests were performed on specimens with different orientations with reference to the printing direction. In detail, Young’s modulus and Poisson’s ratios were evaluated for samples oriented along three different orientations with regard to the printing deposition layers: longitudinally (L), transversally (T) and diagonally (D) to them. Digital Image Correlation (DIC) optical measuring system was used to acquire the full strain fields during the test. Microstructural analysis was also carried out to study the inherent microstructure, characterized by a distinctive grain growth direction, and to assess the preferred crystallographic orientations of specimens extracted along the three considered directions. The experimental results are used to calibrate the orthotropic elastic model. From the calibrated model additional material properties in terms of Young’s and shear modulus for any printing direction are derived. The resulting values exhibit very large variations with the printing angle, with ratios between minimum to maximum values around 2 for the Young’s modulus and 3.5 for the shear modulus. This marked orthotropic behavior could open unexplored design possibilities based on deformability issues. Additionally, the calibrated orthotropic model can also be used for future experimental explorations of the mechanical properties of WAAM alloys and for stiffness-based structural design optimizations.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Additive Manufacturing Materials and Processes · Welding Techniques and Residual Stresses · Manufacturing Process and Optimization
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (42)
Show source-provided references
1. A review of wire arc additive manufacturing and advances in wire arc additive manufacturing of aluminium10.1080/02670836.2018.1455012 ↗
2. Current status and perspectives on wire and arc additive manufacturing (WAAM)10.3390/ma12071121 ↗
3. Metal 3D printing in construction: a review of methods, research, applications, opportunities and challenges10.1016/j.engstruct.2018.11.045 ↗
4. Epitaxy and microstructure evolution in metal additive manufacturing10.1146/annurev-matsci-070115-031728 ↗
5. Metal additive manufacturing: a review of mechanical properties10.1146/annurev-matsci-070115-032024 ↗
6. Fatigue crack growth anisotropy, texture and residual stress in austenitic steel made by wire and arc additive manufacturing10.1016/j.msea.2018.03.075 ↗
7. Evolution of crystallographic orientation, precipitation, phase transformation and mechanical properties realized by enhancing deposition current for dual-wire arc additive manufactured Ni-rich NiTi alloy
8. Evolution of crystallographic orientation, columnar to equiaxed transformation and mechanical properties realized by adding TiCps in wire and arc additive manufacturing 2219 aluminum alloy
9. Characterization of wire arc additive manufacturing 2Cr13 part: process stability, microstructural evolution, and tensile properties10.1016/j.jallcom.2018.03.222 ↗
10. Microstructural evolution and mechanical properties of a low-carbon low-alloy steel produced by wire arc additive manufacturing10.1007/s00170-019-04393-8 ↗
11. Printability of multiwalled SS 316L by wire arc additive manufacturing route with tunable texture10.1016/j.matlet.2019.126981 ↗
12. Effect of solidification defects and HAZ softening on the anisotropic mechanical properties of a wire arc additive-manufactured low-carbon low-alloy steel part10.1007/s11837-019-03773-5 ↗
13. Mechanical properties of wire plus arc additive manufactured steel and stainless steel structures10.1007/s40194-019-00775-4 ↗
14. A.S. Yildiz, K. Davut, B. Koc, O. Yilmaz, Wire Arc Additive Manufacturing of High-strength Low Alloy Steels: Study of Process Parameters and Their Influence on the Bead Geometry and Mechanical Characteristics, 2020.10.1007/s00170-020-05482-9 ↗
15. Anisotropic mechanical properties and deformation behavior of low-carbon high-strength steel component fabricated by wire and arc additive manufacturing10.1016/j.msea.2020.139514 ↗
16. Microstructure and mechanical properties of 304L steel fabricated by arc additive manufacturing10.1051/matecconf/201712803006 ↗
17. Mechanical and microstructural testing of wire and arc additively manufactured sheet material10.1016/j.matdes.2020.108675 ↗
18. Geometrical characterization of Wire-and-Arc Additive Manufactured steel elements10.5185/amlett.2019.0019 ↗
19. Experimental results for structural design of Wire-and-Arc Additive Manufactured stainless steel members10.1016/j.jcsr.2019.105858 ↗
20. Tensile properties and microstructural features of 304L austenitic stainless steel produced by wire-and-arc additive manufacturing10.1007/s00170-019-04868-8 ↗
21. Assessment of design mechanical parameters and partial safety factors for Wire-and-Arc Additive Manufactured stainless steel10.1016/j.engstruct.2020.111314 ↗
22. On the influence of the geometrical irregularities in the mechanical response of Wire-and-Arc Additively Manufactured planar elements10.1016/j.jcsr.2020.106490 ↗
23. MX3D Webpage, (n.d.). www.mx3d.com.
24. Metallic materials - tensile testing
25. Metallic materials — Tensile testing — Part 1: Method of test at room temperature Matériaux métalliques — Essai de traction — Partie 1: Méthode d′essai à température ambiante COPYRIGHT PROTECTED DOCUMENT, Iso 6892–1. 2009. http://files.instrument.com.cn/FilesCenter/20090913/200991371610112081.pdf.
26. B. Strnadel, J. Brumek, The Size Effect in Tensile Test of Steels, 2013. https://doi.org/10.1115/PVP2013-98162.10.1115/PVP2013-98162 ↗
27. Specimen size effects on tensile properties of neutron-irradiated steels10.1016/0022-3115(91)90113-L ↗
28. E3 preparation of metallographic specimens
29. G.F. Vander Voort, G.M. Lucas, E.P. Manilova, Metallography and microstructures of stainless steels and maraging steels, Mater. Park. OH ASM Int. 2004, 670–700.10.31399/asm.hb.v09.a0003767 ↗
30. Role of substrate and deposition conditions on the texture evolution of titanium nitride thin film on bare and plasma-nitrided high-speed steel10.1186/2251-7235-7-66 ↗
31. Effect of nanodiamond concentration and the current density of the electrolyte on the texture and mechanical properties of Ni/Nanodiamond composite coatings produced by electrodeposition
32. A.H. Committee, ASM Handbook, Volume 1: Properties and Selection: Irons, Steels, and High-Performance Alloys, n.d.
33. Kaw · 2005
34. Correlation between arc mode, microstructure, and mechanical properties during wire arc additive manufacturing of 316L stainless steel10.1016/j.msea.2019.02.078 ↗
35. Critical assessment 16: anisotropy in metals10.1179/1743284715Y.0000000118 ↗
36. Monocrystal-polycrystal elastic constants of a stainless steel10.1002/pssa.2210850111 ↗
37. Predicted monocrystal elastic constants of 304-type stainless steel10.1016/0378-4363(85)90076-2 ↗
38. Introduzione alla meccanica dei solidi
39. Staab · 2015
40. The polar formalism
41. Determination of the shear modulus of orthotropic materials from off-axis tension tests10.1016/j.compstruct.2003.09.008 ↗
42. Simultaneous design of the topology and the build orientation of Wire-and-Arc Additively Manufactured structural elements10.1016/j.compstruc.2020.106370 ↗