A survey of finite element analysis of temperature and thermal stress fields in powder bed fusion Additive Manufacturing
Source abstract
Abstract
Abstract This survey aims to provide a review on the application of finite element method to optimize process parameters and improve the mechanical performance of a part fabricated by powder-bed-fusion Additive Manufacturing process. The state-of-the-art finite element models in the simulation of powder bed fusion process are reviewed. Numerical modeling methodologies of the laser beam melting or electron beam melting process at the macro-level are summarized in detail. Specifically, the importance of pre-processing of the part model, process parameters, mesh scheme, and temperature-dependent material properties are clarified. Simulation techniques used to reduce the computational cost are also discussed. Then the existing finite element models in the simulation of powder-bed fusion processes are reviewed and discussed. Simulation results are classified based on the characteristics of the melt pool and the printed part. Then the simulation results are validated by the experiment results. Finally, the significance of finite element method in the connection of other Additive Manufacturing issues such as material design, in-process monitoring and control, and process optimization are explained. The drawbacks of existing finite element models are summarized. And potential new methods to optimize process parameters of PBF process are proposed.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Additive Manufacturing Materials and Processes · Additive Manufacturing and 3D Printing Technologies · Manufacturing Process and Optimization
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (100+)
Show source-provided references
1. Standard · 2012
2. A review on process monitoring and control in metal-based additive manufacturing10.1115/1.4028540 ↗
3. Gibson · 2010
4. A review of additive manufacturing10.5402/2012/208760 ↗
5. Consolidation phenomena in laser and powder-bed based layered manufacturing10.1016/j.cirp.2007.10.004 ↗
6. Thermography for monitoring the selective laser melting process
7. Numerical prediction of temperature and density distributions in selective laser sintering processes10.1108/13552549910251846 ↗
8. Additive manufacturing: overview and NDE challenges
9. Selective laser melting of iron-based powder10.1016/j.jmatprotec.2003.11.051 ↗
10. Selective laser melting of biocompatible metals for rapid manufacturing of medical parts10.1108/13552540710776142 ↗
11. Selective laser melting of high aspect ratio 3D nickel–titanium structures two way trained for MEMS applications10.1007/s10999-007-9032-4 ↗
12. Structural, mechanical and in vitro characterization of individually structured Ti–6Al–4V produced by direct laser forming10.1016/j.biomaterials.2005.07.041 ↗
13. New applications of rapid prototyping and rapid manufacturing (RP/RM) technologies for space instrumentation10.1016/j.actaastro.2007.01.004 ↗
14. Selective laser melting of heat transfer devices10.1108/13552540710824797 ↗
15. High power selective laser melting (HP SLM) of aluminum parts10.1016/j.phpro.2011.03.035 ↗
16. Physical aspects of process control in selective laser sintering of metals10.1002/adem.200310099 ↗
17. The biocompatibility of dense and porous nickel–titanium produced by selective laser melting10.1016/j.msec.2012.09.008 ↗
18. Composites by rapid prototyping technology10.1016/j.matdes.2009.07.045 ↗
19. Additive layered manufacturing: sectors of industrial application shown through case studies10.1080/00207540903479786 ↗
20. Three-Dimensional temperature gradient mechanism in selective laser melting of ti-6al-4v10.1115/1.4028539 ↗
21. Mesoscopic simulation of selective beam melting processes10.1016/j.jmatprotec.2010.12.016 ↗
22. Benchmarking of rapid prototyping techniques in terms of dimensional accuracy and surface finish10.1016/S0007-8506(07)62296-3 ↗
23. A study on shrinkage compensation of the SLS process by using the Taguchi method10.1016/S0890-6955(02)00070-6 ↗
24. Defect generation and propagation mechanism during additive manufacturing by selective beam melting10.1016/j.jmatprotec.2014.05.002 ↗
25. An experimental investigation into additive manufacturing-induced residual stresses in 316L stainless steel10.1007/s11661-014-2549-x ↗
26. Advanced lattice support structures for metal additive manufacturing10.1016/j.jmatprotec.2013.01.020 ↗
27. An innovative method to build support structures with a pulsed laser in the selective laser melting process10.1007/s00170-011-3470-8 ↗
28. Residual stress and distortion modeling of electron beam direct manufacturing Ti-6Al-4V
29. A review of thermal analysis methods in laser sintering and selective laser melting
30. Simulation of metallic powder bed additive manufacturing processes with the finite element method: a critical review
31. Multi-Scale modeling of powder-bed-based additive manufacturing10.1146/annurev-matsci-070115-032158 ↗
32. A review of computational modelling of additive layer manufacturing–multi-scale and multi-physics
33. Reddy · 2010
34. 3D FE simulation for temperature evolution in the selective laser sintering process10.1016/j.ijmachtools.2003.10.019 ↗
35. 3 D finite element analysis in the selective laser melting process10.2507/IJSIMM10(3)1.169 ↗
36. Finite element simulation of the temperature and stress fields in single layers built without-support in selective laser melting10.1016/j.matdes.2013.05.070 ↗
37. Comparisons of numerical modelling of the selective laser melting
38. Finite element analysis of single layer forming on metallic powder bed in rapid prototyping by selective laser processing10.1016/S0890-6955(01)00093-1 ↗
39. Numerical simulation of temperature field during selective laser sintering of polymer-coated molybdenum powder10.1016/S1003-6326(06)60264-1 ↗
40. Selective laser sintering of an amorphous polymer—simulations and experiments10.1243/0954405991516822 ↗
41. Process parameter selection for selective laser melting of Ti6Al4V based on temperature distribution simulation and experimental sintering10.1007/s00170-011-3776-6 ↗
42. Numerical thermal analysis in electron beam additive manufacturing with preheating effects
43. Stress and deformation evaluations of scanning strategy effect in selective laser melting10.1016/j.addma.2016.05.007 ↗
44. Effect of thermal deformation on part errors in metal powder based additive manufacturing processes10.1115/1.4026524 ↗
45. Implementation of a thermomechanical model for the simulation of selective laser melting10.1007/s00466-014-1024-2 ↗
46. Residual stresses in selective laser sintering and selective laser melting10.1108/13552540610707013 ↗
47. Temperature measurements during selective laser sintering of titanium powder10.1016/j.ijmachtools.2004.04.019 ↗
48. The influence of processing parameters on the mechanical properties of selectively laser melted stainless steel microlattice structures10.1115/1.4001743 ↗
49. Research on the fabricating quality optimization of the overhanging surface in SLM process10.1007/s00170-012-4271-4 ↗
50. Simulation of temperature field in selective laser sintering of copper powder
51. Study on reduction of residual stress induced during rapid tooling process: influence of heating conditions on residual stress10.4028/www.scientific.net/KEM.447-448.785 ↗
52. An experimental design approach to selective laser sintering of low carbon steel10.1016/S0924-0136(03)00132-8 ↗
53. Li · 2018
54. Evaluation of residual stress in stainless steel 316L and Ti6Al4V samples produced by selective laser melting10.1080/17452759.2015.1026045 ↗
55. Thermal stresses and deposition patterns in layered manufacturing10.1016/S0921-5093(01)01179-0 ↗
56. Distortion minimization of laser-processed components through control of laser scanning patterns10.1108/13552540210451732 ↗
57. Effect of path planning on the laser powder deposition process: thermal and structural evaluation10.1007/s00170-010-2659-6 ↗
58. Selective laser sintering (melting) of stainless and tool steel powders: experiments and modelling10.1243/095440505X8109 ↗
59. Masubuchi · 2013 · vol. 33
60. Modelling of radiation transfer in metallic powders at laser treatment10.1016/j.ijheatmasstransfer.2005.01.044 ↗
61. Model of thermal conductivity in powder beds10.1103/PhysRevB.80.024202 ↗
62. Finite element analysis of residual stresses and deformations in direct metal SLS process
63. Finite element analysis of temperature distribution in single metallic powder layer during metal laser sintering10.1016/j.ijmachtools.2006.09.025 ↗
64. Finite element analysis of melting and solidifying processes in laser rapid prototyping of metallic powders10.1016/S0890-6955(98)00036-4 ↗
65. Single track formation in selective laser melting of metal powders10.1016/j.jmatprotec.2010.05.010 ↗
66. Absorptance of powder materials suitable for laser sintering10.1108/13552540010337029 ↗
67. Simulation and experimental verification of crystalline polymer and direct metal selective laser sintering
68. Laser sintering of metal powders on top of sintered layers under multiple-line laser scanning10.1088/0022-3727/40/21/036 ↗
69. Three-dimensional transient finite element analysis of the selective laser sintering process10.1016/j.jmatprotec.2008.02.040 ↗
70. Numerical and experimental investigations on laser melting of stainless steel 316L metal powders10.1016/j.jmapro.2014.04.001 ↗
71. Venuvinod · 2013
72. A three-dimensional finite element analysis of the temperature field during laser melting of metal powders in additive layer manufacturing10.1016/j.ijmachtools.2009.07.004 ↗
73. Photopyroelectric measurement of thermal conductivity of metallic powders10.1063/1.1832740 ↗
74. Light extinction in metallic powder beds: correlation with powder structure10.1063/1.1948509 ↗
75. Three-dimensional modeling of laser sintering of a two-component metal powder layer on top of sintered layers10.1115/1.2716714 ↗
76. Mechanisms of selective laser sintering and heat transfer in Ti powder10.1108/13552540310502211 ↗
77. Studies on effective thermal conductivities in packed beds10.1002/aic.690030317 ↗
78. A three dimensional model for selective laser sintering
79. Research on measurement method of selective laser sintering (SLS) transient temperature10.1016/j.ijleo.2007.01.010 ↗
80. Wärmeleitfähigkeit von Schüttungen bei mäßigen Temperaturen10.1002/cite.330421408 ↗
81. Simulation of temperature distribution in single metallic powder layer for laser micro-sintering10.1016/j.commatsci.2011.09.012 ↗
82. Thermal modeling of electron beam additive manufacturing process: powder sintering effects
83. Micro scale 3D FEM simulation on thermal evolution within the porous structure in selective laser sintering10.1016/j.jmatprotec.2012.05.010 ↗
84. Parametric analysis of thermal behavior during selective laser melting additive manufacturing of aluminum alloy powder10.1016/j.matdes.2014.07.006 ↗
85. Heat capacity and other thermodynamic properties of linear macromolecules. VII. Other carbon backbone polymers10.1063/1.555677 ↗
86. Thermophysical properties of solid and liquid Ti-6Al-4V (TA6V) alloy10.1007/PL00021868 ↗
87. Metal additive-manufacturing process and residual stress modeling
88. Microstructural evolution in laser-deposited multilayer Ti-6Al-4V builds: part II. Thermal modeling10.1007/s11661-004-0095-7 ↗
89. Analytical and numerical modelling of the direct metal deposition laser process10.1088/0022-3727/41/2/025403 ↗
90. An analytical–numerical model of laser direct metal deposition track and microstructure formation10.1088/0965-0393/19/5/055003 ↗
91. A multiphase mechanical model for Ti–6Al–4V: application to the modeling of laser assisted processing10.1016/j.commatsci.2009.05.012 ↗
92. Modelling phase change in a 3D thermal transient analysis10.1260/1750-9548.8.1.49 ↗
93. Comparison of 3DSIM thermal modelling of selective laser melting using new dynamic meshing method to ANSYS10.1179/1743284714Y.0000000703 ↗
94. Deal. II—a general-purpose object-oriented finite element library10.1145/1268776.1268779 ↗
95. Modeling metal deposition in heat transfer analyses of additive manufacturing processes10.1016/j.finel.2014.04.003 ↗
96. Li · 2018
97. Simulation of transient temperature field in the selective laser sintering process of W/Ni powder mixture
98. Effect of stress relaxation on distortion in additive manufacturing process modeling
99. Experimental validation of finite element modeling for laser powder bed fusion deformation
100. An integrated approach to cyber-enabled additive manufacturing using physics based, coupled multi-scale process modeling