Numerical analysis of particle impacting and bonding processes during high velocity oxygen fuel spraying process
Source abstract
Abstract
Abstract In this paper, the dynamic impact behavior of a particle and a substrate under different particle temperatures and velocities as well as using different materials for the particle and substrate were systematically studied. We found that the highest temperature occurred at the side edge of the particle after the collision, which is consistent with the distribution of equivalent plastic strain. The deformation of the particle and substrate was very severe at the first 40 ns, slowed down after 40 ns and remained almost unchanged after 80 ns. With the increase in the particle velocity, the effective combination area became larger, the equivalent plastic strain of the substrate is increased, and the equivalent plastic strain of the particle is decreased. As the initial temperature of particles increased, the effective combination area between the particle and substrate increased, and higher temperature and larger equivalent plastic strain of the particle could be obtained. With the increase in the substrate strength, the temperature and the equivalent plastic strain of the particle is increased, whereas the plastic deformation of the substrate is decreased.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: High-Velocity Impact and Material Behavior · High-Temperature Coating Behaviors · Particle Dynamics in Fluid Flows
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (20)
Show source-provided references
1. Numerical analysis of partially molten splat during thermal spray process using the finite element method10.1016/j.apsusc.2009.12.158 ↗
2. Modeling aspects of high velocity impact of particles in cold spraying by explicit finite element analysis10.1007/s11666-009-9325-2 ↗
3. Effect of particle impact on residual stress development in HVOF sprayed coatings10.1361/105996306X146703 ↗
4. Numerical and experimental investigations of splat geometric characteristics during oblique impact of plasma spraying10.1016/j.apsusc.2011.06.081 ↗
5. Numerical analysis of the effect of the gas temperature on splat formation during thermal spray process10.1016/j.apsusc.2010.08.115 ↗
6. Modeling the impact, flattening and solidification of a molten droplet on a solid substrate during plasma spraying10.1016/j.apsusc.2014.08.032 ↗
7. Interface bonding between particle and substrate during HVOF spraying10.1016/j.apsusc.2014.08.196 ↗
8. A hybrid approach to determine critical and erosion velocities in the cold spray process10.1016/j.apsusc.2013.02.089 ↗
9. Numerical investigations of the effect of oblique impact on particle deformation in cold spraying by the SPH method10.1016/j.apsusc.2010.01.014 ↗
10. Some aspects on 3D numerical modeling of high velocity impact of particles in cold spraying by explicit finite element analysis10.1016/j.apsusc.2009.04.135 ↗
11. Deposition characteristics of copper particles on roughened substrates through kinetic spraying10.1016/j.apsusc.2008.10.060 ↗
12. On high velocity impact of micro-sized metallic particles in cold spraying10.1016/j.apsusc.2006.05.126 ↗
13. Numerical simulation of deformation behavior of Al particles impacting on Al substrate and effect of surface oxide films on interfacial bonding in cold spraying10.1016/j.apsusc.2006.11.020 ↗
14. Effect of impact-induced melting on interface microstructure and bonding of cold-sprayed zinc coating10.1016/j.apsusc.2010.08.089 ↗
15. Fracture characteristics of three metals subjected to various strains, strain rates, temperatures and pressures10.1016/0013-7944(85)90052-9 ↗
16. Improvement on mechanical properties and wear resistance of HVOF sprayed WC-12Co coatings by optimizing feedstock structure10.1016/j.apsusc.2014.09.081 ↗
17. Effect of CeO2 addition on thermal shock resistance of WC–12%Co coating deposited on ductile iron by electric contact surface strengthening10.1016/j.apsusc.2015.05.064 ↗
18. Effect of shot peening on the oxidation behavior of thermal barrier coatings10.1016/j.apsusc.2015.06.113 ↗
19. Thermophysical and microstructural studies on thermally sprayed tungsten carbide-cobalt coatings10.1007/s11666-010-9558-0 ↗
20. Bonding mechanism from the impact of thermally sprayed solid particles10.1007/s11661-009-9959-1 ↗