A hybrid additively manufactured martensitic-maraging stainless steel with superior strength and corrosion resistance for plastic injection molding dies
Source abstract
Abstract
Abstract The customization of plastic injection molding dies is technologically and economically limited by conventional manufacturing processes. Recent advances in hybrid additive manufacturing (HAM) have provided more geometrical freedom for the manufacturing of parts with desired properties. In this paper, we report manufacturing of a hybrid 420/Corrax stainless steel with a reliable interface that can be applied in the manufacturing of next-generation geometrically complex plastic injection molding dies with enhanced strength and corrosion resistance. AISI 420 martensitic stainless steel is used as a cost-effective substrate, and a maraging stainless steel grade, known as Corrax, is printed on top of it using laser powder bed fusion (LPBF). A hybrid heat treatment cycle is applied to improve metallurgical properties and to enhance mechanical compatibility between the martensitic and the maraging stainless steels. Tensile tests coupled with scanning electron microscopy are carried out for analysis of failure, which show the development of shear bands in the microstructure of the 420 stainless steel substrate while a limited amount of deformation occurs in the interface region and Corrax microstructure. Void nucleation, growth, and coalescence are found at the 420/Corrax interface due to mechanical incompatibility and decohesion; however, microstructural instability mainly occurs along the shear bands on the 420 side and leads to fracture, which is quantified using high-resolution X-ray computed tomography. Nanoindentation tests show that the maximum level of hardness occurs at the interface due to the existence of sub-micron grains and the formation of AlN nanoparticles. Also, the formation of β-NiAl precipitates enhances the Corrax strength after heat treatment. In addition to a high strength, elevated corrosion resistance of the cooling channels is essential to extend the service life of plastic injection molding dies. Potentiodynamic corrosion testing at the interface shows that Corrax has remarkable corrosion resistance compared to 420. Therefore, additive manufacturing of the critical die areas such as the cooling channels using Corrax increases the service life of the mold.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Additive Manufacturing Materials and Processes · Additive Manufacturing and 3D Printing Technologies · High Entropy Alloys Studies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (67)
Show source-provided references
1. Metastable high-entropy dual-phase alloys overcome the strength-ductility trade-off10.1038/nature17981 ↗
2. Bone-like crack resistance in hierarchical metastable nanolaminate steels10.1126/science.aal2766 ↗
3. Inverse temperature dependence of toughness in an ultrafine grain-structure steel10.1126/science.1156084 ↗
4. Brittle intermetallic compound makes ultrastrong low-density steel with large ductility10.1038/nature14144 ↗
5. Ultrastrong steel via minimal lattice misfit and high-density nanoprecipitation10.1038/nature22032 ↗
6. High tensile ductility in a nanostructured metal10.1038/nature01133 ↗
7. Creep-resistant, Al₂O₃-forming austenitic stainless steels10.1126/science.1137711 ↗
8. Strength and ductility of 316L austenitic stainless steel strengthened by nano-scale twin bundles10.1016/j.actamat.2011.11.009 ↗
9. Additively manufactured hierarchical stainless steels with high strength and ductility10.1038/nmat5021 ↗
10. Evading the strength-ductility trade-off dilemma in steel through gradient hierarchical nanotwins10.1038/ncomms4580 ↗
11. An ultra-high strength martensitic steel fabricated using selective laser melting additive manufacturing: densification, microstructure, and mechanical properties10.1016/j.actamat.2019.12.037 ↗
12. Effect of processing parameters on microstructure and tensile properties of austenitic stainless steel 304L made by directed energy deposition additive manufacturing10.1016/j.actamat.2016.03.019 ↗
13. Solidification-driven orientation gradients in additively manufactured stainless steel10.1016/j.actamat.2019.10.047 ↗
14. Strengthening mechanisms in directed energy deposited austenitic stainless steel10.1016/j.actamat.2018.11.021 ↗
15. Structure/property (constitutive and spallation response) of additively manufactured 316L stainless steel10.1016/j.actamat.2017.07.045 ↗
16. Effects of heat treatment and build orientation on the evolution of ϵ and α′ martensite and strength during compressive loading of additively manufactured 304L stainless steel10.1016/j.actamat.2020.04.036 ↗
17. Solution annealing and precipitation hardening effect on the mechanical properties of 630 stainless steel fabricated via laser melting deposition10.1016/j.msea.2020.139999 ↗
18. Gas atomization and laser additive manufacturing of nitrogen-alloyed martensitic stainless steel
19. Microstructure and mechanical properties of stainless steel CX manufactured by Direct Metal Laser Sintering10.1016/j.msea.2017.10.045 ↗
20. Al–Cu alloy fabricated by novel laser-tungsten inert gas hybrid additive manufacturing
21. Additive manufacturing hybrid Ni/Ti-6Al-4V structural component via selective laser melting and cold spraying10.1016/j.vacuum.2018.02.040 ↗
22. Microstructural investigation and mechanical behavior of a two-material component fabricated through selective laser melting of AlSi10Mg on an Al-Cu-Ni-Fe-Mg cast alloy substrate
23. Wire-arc additive manufacturing of nickel aluminum bronze/stainless steel hybrid parts – Interfacial characterization, prospects, and problems10.1016/j.mtla.2020.100834 ↗
24. Microstructure and mechanical properties of additively manufactured multi-material component with maraging steel on CrMn steel10.1016/j.msea.2020.140630 ↗
25. Hybrid parts produced by deposition of 18Ni300 maraging steel via selective laser melting on forged and heat treated advanced high strength steel
26. Additive manufacturing of maraging steel-H13 bimetals using laser powder bed fusion technique
27. Numerical tools to investigate mechanical and fatigue properties of additively manufactured MS1-H13 hybrid steels
28. Metallurgical and mechanical assessment of hybrid additively-manufactured maraging tool steels via selective laser melting
29. Microstructures and fatigue behavior of additively manufactured maraging steel deposited on conventionally manufactured base plate10.1007/s11665-021-05548-z ↗
30. A novel ultra-high strength maraging steel with balanced ductility and creep resistance achieved by nanoscale β-NiAl and Laves phase precipitates10.1016/j.actamat.2018.02.044 ↗
31. Massive nanoprecipitation in an Fe-19Ni-xAl maraging steel triggered by the intrinsic heat treatment during laser metal deposition10.1016/j.actamat.2017.02.069 ↗
32. Additive manufacturing of an Fe – Cr – Ni – Al maraging stainless steel: microstructure evolution, heat treatment, and strengthening mechanisms10.1016/j.msea.2020.139470 ↗
33. Precipitation in 18 wt% Ni maraging steel of grade 35010.1016/S1359-6454(99)00370-5 ↗
34. Ageing behaviour of an Fe-20Ni-1.8Mn-1.6Ti-0.59Al (wt%) maraging alloy: clustering, precipitation and hardening10.1016/j.actamat.2004.08.018 ↗
35. Effects of austenitizing temperature on the microstructure and electrochemical behavior of a martensitic stainless steel10.1007/s10800-015-0796-1 ↗
36. Effects of Cl− concentration and temperature on pitting of AISI 304 stainless steel10.5006/1.3584938 ↗
37. Is Hybrid Manufacturing Technology the Future of Additive Manufacturing?, Addit. Manuf., 2018. 〈https://amfg.ai/2018/07/10/hybrid-technology-the-future-of-manufacturing/〉.
38. Hybrid Machines Make Parts Using Brand New and Tried and True Technologies, Soc. Manuf. Eng., 2018. 〈https://www.sme.org/hybrid-machines-make-parts-using-brand-new-tried-and-true〉.
39. Hybrid rapid prototyping system using machining and deposition10.1016/S0010-4485(01)00203-2 ↗
40. Standard Test Methods for Tension Testing of Metallic Materials, ASTM E8 / E8M - 15a. (n.d.).
41. Digital image correlation studies for microscopic strain distribution and damage in dual phase steels10.1016/j.scriptamat.2007.01.031 ↗
42. Quantitative microstructural analysis of formability enhancement in dual phase steels subject to electrohydraulic forming10.1007/s11665-012-0438-2 ↗
43. Strain localization and damage in dual phase steels investigated by coupled in-situ deformation experiments and crystal plasticity simulations10.1016/j.ijplas.2014.06.004 ↗
44. X-ray microcomputed tomography in additive manufacturing: a review of the current technology and applications10.1089/3dp.2018.0060 ↗
45. 4D X-ray tomography characterization of void nucleation and growth during deformation of strontium-added AZ31 alloys10.1016/j.msea.2020.140081 ↗
46. Microstructural design for damage tolerance in high strength steels10.1016/j.matlet.2020.127664 ↗
47. In-situ X-ray tomography analysis of the evolution of pores during deformation of a Cu-Sn alloy fabricated by selective laser melting
48. In-situ X-ray tomography analysis of the evolution of pores during deformation of AlSi10Mg fabricated by selective laser melting10.1016/j.matlet.2019.126512 ↗
49. The role of microstructure on edge cracks in dual phase and quench and partitioning steels subject to severe cold rolling10.1016/j.scriptamat.2019.08.012 ↗
50. Multi-scale morphological characterization of Ni foams with directional pores10.1016/j.matchar.2019.109939 ↗
51. Initiation and growth of damage in a dual-phase steel observed by X-ray microtomography10.1016/j.actamat.2008.06.015 ↗
52. 3D micromechanical modeling of dual phase steels using the representative volume element method10.1016/j.mechmat.2016.07.011 ↗
53. Metallurgical investigations on hyperplasticity in dual phase steel sheets10.1115/1.4027492 ↗
54. Analysis of failure in dual phase steel sheets subject to electrohydraulic forming10.1115/1.4027940 ↗
55. Microstructural analysis of ductility and fracture in fine-grained and ultrafine-grained vanadium-added DP1300 steels10.1016/j.ijplas.2017.12.009 ↗
56. Microstructural evolution during deformation of a QP980 steel10.1007/s11661-020-05882-2 ↗
57. Influence of strain path on nucleation and growth of voids in dual phase steel sheets10.1016/j.matdes.2015.12.103 ↗
58. Simultaneous enhancement of strength and ductility through coordination deformation and multi-stage transformation induced plasticity (TRIP) effect in heterogeneous metastable austenitic steel10.1016/j.scriptamat.2018.12.007 ↗
59. Fracture characteristics of thermally exposed 9Cr – 1Mo steel after tensile and impact testing at room temperature10.1016/j.engfailanal.2008.09.003 ↗
60. High temperature tensile properties and fracture characteristics of bimodal 12Cr-ODS steel10.1016/j.jnucmat.2015.11.013 ↗
61. The effect of heat treatment on mechanical properties and corrosion behavior of AISI420 martensitic stainless steel10.1016/j.jallcom.2010.12.174 ↗
62. Effect of austenitizing heat treatment on the microstructure and hardness of martensitic stainless steel AISI 42010.1007/s11665-011-0043-9 ↗
63. Influence of M23C6 carbides on the heterogeneous strain development in annealed 420 stainless steel10.1016/j.actamat.2020.08.072 ↗
64. Standard test methods for determining average grain size using semiautomatic and automatic image analysis, ASTM E1382 - 97., 2015.
65. The deformation and ageing of mild steel: III discussion of results10.1088/0370-1301/64/9/303 ↗
66. Influence of tempering temperature on stability of carbide phases in 2.6cr-0.7mo-0.3v steel with various carbon content10.1007/BF02647972 ↗
67. Formation of M23C6-type precipitates and chromium-depleted zones in austenite stainless steel10.1016/j.scriptamat.2011.06.010 ↗