journal article·2024-03-03

Kink band orientation of 3D printed continuous carbon fiber composites under compressive loading

Ahmad Zuhair Bin Zakaria, Takuya Takahashi, Akira Todoroki, Masahito Ueda

Advanced Composite Materials· Volume 33· Issue 2
Publisher page

Abstract

For continuous carbon fiber-reinforced plastic (cCFRP), in the case of loading in the longitudinal direction, occurrence of kink band failure causes compression strength to be lower than the tensile strength. Furthermore, 3D-printed cCFRP may exhibit intrinsic compressive behavior depending on the printing orientation. In this study, two types of rectangular specimens were fabricated using the Markforged Mark Two > 3D printer. The first was the in-plane specimen, whose width direction was parallel to the print bed and thickness direction was along the layup direction. The second was the out-of-plane specimen, whose width direction was the layup direction and thickness direction was parallel to the print bed. Compression tests were performed, and the experimental results were compared. As a result, the compressive strengths of both types were similar, and the kink bands always grew in the lay-up direction. For the out-of-plane specimens, nonlinear stress–strain curves were observed. This may be due to the delamination crack growth caused by the low strength in the lay-up direction and the existence of initial defects. This study experimentally investigated the effect of two different printing orientations of 3D printed cCFRP to its strength and failure mode, and this work shows the importance of considering structural deformation due to compression loading in 3D printed cCFRP.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Additive Manufacturing and 3D Printing Technologies · Manufacturing Process and Optimization · Mechanical Behavior of Composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Graduate Student, Tokyo Institute of Technology, Ookayama, 1528550, 2-12-1 Tokyo, Meguro, Japan

Department of Mechanical Engineering, Tokyo Institute of Technology, Ookayama, 1528550, 2-12-1 Tokyo, Meguro, Japan

Department of Mechanical Engineering, Nihon University 101-8308, 1-8-14 Chiyoda, Tokyo, Kanda-Surugadai, Japan

Funding

Tokyo Institute of Technology

References (27)

Show source-provided references
1. Dow NF Rosen BW. Evaluations of filament-reinforced composites for aerospace structural applications. NASA Technical Report NASA-CR-207. 1965. https://ntrs.nasa.gov/citations/19650012756
2. 10.1177/002199836900300104110.1177/0021998369003001041 ↗
3. 10.1177/2F00219983720060031510.1177/2F002199837200600315 ↗
4. 10.1016/B978-0-12-341801-2.50007-210.1016/B978-0-12-341801-2.50007-2 ↗
5. 10.6089/jscm.12.21410.6089/jscm.12.214 ↗
6. 10.1177/00219983920260180410.1177/002199839202601804 ↗
7. 10.1016/0266-3538(94)90041-810.1016/0266-3538(94)90041-8 ↗
8. 10.1007/978-94-011-4659-3_810.1007/978-94-011-4659-3_8 ↗
9. 10.1016/S1359-835X(04)00158-710.1016/S1359-835X(04)00158-7 ↗
10. 10.1016/j.compositesa.2005.12.00410.1016/j.compositesa.2005.12.004 ↗
11. 10.1016/j.compstruct.2009.08.01010.1016/j.compstruct.2009.08.010 ↗
12. 10.1080/09243046.2014.97317310.1080/09243046.2014.973173 ↗
13. 10.1016/j.compositesa.2016.11.01810.1016/j.compositesa.2016.11.018 ↗
14. 10.1016/j.jcomc.2020.10005610.1016/j.jcomc.2020.100056 ↗
15. 10.1016/j.compstruct.2022.11545810.1016/j.compstruct.2022.115458 ↗
16. http://www.3d-caddata.com/news/selective-laser-sintering (Access 2023/02/20)
17. 10.1038/srep2305810.1038/srep23058 ↗
18. 10.4236/ojcm.2016.6100310.4236/ojcm.2016.61003 ↗
19. 10.1016/j.addma.2018.05.00710.1016/j.addma.2018.05.007 ↗
20. 10.1016/j-addma.2019.10088410.1016/j-addma.2019.100884 ↗
21. 10.1016/j.compositesa.2021.10641610.1016/j.compositesa.2021.106416 ↗
22. 10.1016/j.compscitech.2022.10961810.1016/j.compscitech.2022.109618 ↗
23. 10.1080/09243046.2019.165032310.1080/09243046.2019.1650323 ↗
24. Nishi K, Shiratori H, Todoroki A, et al. Effects of nozzle diameter on mechanical properties of 3D printed continuous CFRTP. Reinf Plast. 2022;68:258–264. in Japanese.
25. https://static.markforged.com/markforged_composites_datasheet.pdf (Access 2023/02/20)
26. 10.1016/0045-7949(83)90141-410.1016/0045-7949(83)90141-4 ↗
27. 10.1016/0022-5096(93)90068-Q110.1016/0022-5096(93)90068-Q1 ↗