journal article·2018-12

Wear behaviour of Al 7075/SiC/Mg metal matrix nano composite by liquid state process

S. Suresh, G. Harinath Gowd, M. L. S. Deva Kumar

Publisher page

Abstract

AA7075 base composites, reinforced using nano silicon carbide, contain average particle size 50 nm that is manufactured via stir casting technique, and also their rate of wear and friction coefficient was examined. During the present investigation, applied load and the weight percentage of nano silicon carbide (SiC) varying from 1, 2, 3 and 4% have been studied. The dry sliding wear characteristics of nanocomposites were analysed through pin-on-disk apparatus. By considering sliding speeds of 3and 4 m/s on applied loads of 20, 30 and 40 N. The outcomes reveal that the ceramic reinforcement of the matrix metal with nano-SiC particles up to weight percentage of 4 decreases the rate of wear. The results indicate that by increasing applied load and sliding distance the wear of the test samples raises linearly. The weight loss and friction coefficient relatively reduce with enhancing weight percentage of nano reinforcements. The wear out surfaces are analysed by scanning electron microscope (SEM) which shows that the small grooved zones and minor cracks are identified on the worn out surface of the composite. It signifies abrasive wear behaviour, which is generally of hard SiC particles subjected on the worn surfaces. Moreover, it was noticed from the test results that the wear rate reduces gradually with improving weight percentage of nano-SiC and friction coefficient decreases linearly with increasing load on the specimens, and weight percentage of SiC. The most efficient result attained at 4% weight percentage.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloys Composites Properties · Advanced ceramic materials synthesis · Advanced materials and composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (20)

Show source-provided references
1. Radhika N, Balaji TV, Palaniappan S (2015) Studies on mechanical properties and tribological behaviour of LM25/SiC/Al2O3 composites. J Eng Sci Technol 10(2):134–144
2. Uyyuru RK, Surappa MK, Brusethaug S (2007) Tribological behaviour of Al-Si-SiCp composites/automobile pad system under dry sliding conditions. Tribol Int 40:365–37310.1016/j.triboint.2005.10.012 ↗
3. Rao RN, Das S (2010) Effect of heat treatment on the sliding wear behaviour of aluminium alloy (Al Zn-Mg) hard particle composite. Tribol Int 43:330–33910.1016/j.triboint.2009.06.013 ↗
4. Kumar S (2010) Effect of reinforcement size, and volume fraction on the abrasive wear of AA7075 Al/SiCp P/M composites-a statistical analysis. Tribol Int 43:414–42210.1016/j.triboint.2009.07.003 ↗
5. Uthayakumar M, Aravindan S, Rajkumar K (2013) Wear performance of Al-SiC–B4C hybrid composites under dry sliding conditions. Mater Des 47:456–46410.1016/j.matdes.2012.11.059 ↗
6. Kumar S, Panwar RS, Pandey OP (2012) Tribological characteristics of aluminium reinforced particles composites developed by liquid metallurgy route. Adv Mater Res 585:574–57810.4028/www.scientific.net/AMR.585.574 ↗
7. Nagendra Naik M, Dharma Reddy K, Venkata Ramaiah P, Venkata Narayana B, Bhanodaya Reddy G (2017) Exploration of mechanical behaviour and wear behaviour of Al4C3 reinforced aluminium metal matrix composites. Materials Today: Proceedings 4(2017):2989–2998
8. Fadhil MC, Ravikiran BS (2016) The dry-sliding wear behavior of aluminium alloy/SiC metal matrix composites. International Journal of Advances in Scientific Research and Engineering 02(08):1–6
9. Uvaraja VC, Natarajan N, Sivakumar K, Jegadheeshwaran S, Sudhakar S (2015) Tribological behavior of heat treated Al 7075 aluminium metal matrix composites. Indian Journal of Engineering & Materials Sciences 22:51–61
10. Ramakoteswara Rao V, Ramanaiah N, Sarcar MMM (2016) Tribological properties of aluminium metal matrix composites (AA7075 reinforced with titanium carbide (TiC) particles). International Journal of Advanced Science and Technology 88:13–2610.14257/ijast.2016.88.02 ↗
11. Baradeswaran S, Vettivel C, ElayaPerumal A, Selvakumar N, Franklin Issac R (2014) Experimental investigation on mechanical behaviour, modelling, and optimisation of wear parameters of B4C and graphite reinforced aluminium hybrid composites. Mater Des 63:620–63210.1016/j.matdes.2014.06.054 ↗
12. Acilar M, Gul F (2004) Effect of the applied load, sliding distance and oxidation on the dry sliding wear behaviour of Al-10Si/SiCp composites produced by vacuum infiltration technique. Mater Des 25:209–21710.1016/j.matdes.2003.09.015 ↗
13. Umanath K, Selvamani ST, Palanikumar K (2011) Friction and wear behaviour of Al6061 alloy (SiCP/ Al2O3P) hybrid composites. Int J Eng Sci Technol 3(7):5441–5451
14. Das S, Behera R, Datta A, Majumdar G, Oraon B, Sutradhar G (2010) Experimental investigation on the effect of reinforcement particles on the forgeability and the mechanical properties of Al MMCs. Mater Sci Appl 1:310–316
15. Mishra AK, Sheokand R, Srivastava RK (2012) Tribological Behaviour of Al-6061/SiC metal matrix composite by Taguchi’s techniques. International Journal of Scientific and Research Publications 2(10):1–8
16. Das S, Das S, Das K (2007) Abrasive wear of zircon sand and alumina reinforced Al-4.5wt% Cu alloy matrix composites—a comparative study. Compos Sci Technol 67:746–75110.1016/j.compscitech.2006.05.001 ↗
17. Deuis RL, Subramanian C, Yellup JM (1997) Dry sliding wear of aluminum composites—a review. Compos Sci Technol 57:415–43510.1016/S0266-3538(96)00167-4 ↗
18. Umanath K, Selvamani ST, Natarajan K (2010) Influence of silicon carbide particulate reinforcement on the tensile behaviour of Al6061 alloy composite produced by stir casting method. In Proceedings of Manufacturing, (ARAI, Pune), pp 235–242
19. Singla M, Singh L, Chawla V (2009) Study of wear properties of Al-SiC composites. J Miner Mater Charact Eng 8(10):813–819
20. Dhanalakshmi S, Mohanasundararaju N, Venkatekrishnan PG (2014) Preparation and mechanical characterization of stir cast hybrid Al7075- Al2O3-B4C metal matrix composites. Appl Mech Mater 592-594:705–71010.4028/www.scientific.net/AMM.592-594.705 ↗