A rheometric approach to assess plastic shrinkage and implications of early age drying on the microstructure of cement-based materials
Source abstract
Abstract
3D printed cementitious materials are subjected to environmental drying from a very early age as it does not have any formwork protection. In this paper, we present a novel methodology using a rheometer for measuring the shrinkage strains in such stiff cement-based materials from the onset of processing. In this approach, cylindrical samples are placed between parallel plates attached to the rheometer and continuous monitoring of shrinkage strain is made possible by using a constant normal force protocol. Using this protocol, shrinkage strain was measured in samples subjected to external drying and protected from drying and also on samples with and without shrinkage reducing agent. It was found that the incorporation of about 3 wt% shrinkage reducing agent significantly reduces the early-age shrinkage strain. The effect of early-age drying induced microstructural changes was investigated in this study using mercury intrusion porosimetry, loss on ignition and electrical resistivity measurements. When subjected to early age drying, the porosity of the samples was found to increase significantly and the assessment of chemically bound water revealed that the degree of hydration was not uniform, but varied as a gradient with the minimal values at the drying surface.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Innovations in Concrete and Construction Materials · Concrete and Cement Materials Research · Innovative concrete reinforcement materials
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (67)
Show source-provided references
1. Mitigating early age cracking in 3D printed concrete using fibres, superabsorbent polymers, shrinkage reducing admixtures, B-CSA cement and curing measures10.1016/j.cemconres.2022.106862 ↗
2. Plastic shrinkage cracking in 3D printed concrete10.1016/j.compositesb.2020.108313 ↗
3. Digital image correlation (DIC) on fresh cement mortar to quantify settlement and shrinkage10.1016/j.acme.2018.10.003 ↗
4. Early age shrinkage phenomena of 3D printed cementitious materials with superabsorbent polymers
5. Application of image analysis to monitor very early age shrinkage
6. A review on testing methods for autogenous shrinkage measurement of cement-based materials
7. Extrusion-based concrete 3D printing from a material perspective: a state-of-the-art review10.1016/j.cemconcomp.2020.103855 ↗
8. Performance criteria, environmental impact and cost assessment for 3D printable concrete mixtures10.1016/j.resconrec.2022.106255 ↗
9. State-of-the-art review on plastic cracking of concrete10.1016/j.conbuildmat.2019.07.197 ↗
10. The effect of restrained early age shrinkage on the interlayer bond and durability of 3D printed concrete
11. A plastic shrinkage cracking risk model for 3D printed concrete exposed to different environments10.1016/j.cemconcomp.2022.104516 ↗
12. Rheological and pumping behaviour of 3D printable cementitious materials with varying aggregate content10.1016/j.cemconres.2020.106258 ↗
13. Cracking risks associated with early age shrinkage10.1016/S0958-9465(03)00068-4 ↗
14. Effect of type and dosage of silica fume on plastic shrinkage in concrete exposed to hot weather10.1016/j.conbuildmat.2004.04.031 ↗
15. 3D printable concrete with natural and recycled coarse aggregates: rheological, mechanical and shrinkage behaviour10.1016/j.cemconcomp.2021.104311 ↗
16. Evaluating the printability of concretes containing lightweight coarse aggregates10.1016/j.cemconcomp.2020.103570 ↗
17. En197-1 · 2004
18. IS 16714 · 2018
19. Interactions between shrinkage reducing admixtures (SRA) and cement paste’s pore solution10.1016/j.cemconres.2007.12.005 ↗
20. Evaluating the influence of aggregate content on pumpability of 3D printable concrete10.1007/978-3-030-49916-7_34 ↗
21. A desorptivity-based approach for the assessment of phase separation during extrusion of cementitious materials10.1016/j.cemconcomp.2020.103546 ↗
22. The effects of lime and admixtures on the water-retaining properties of cement mortars10.1016/S0008-8846(99)00162-3 ↗
23. Effect of polycarboxylate ether super- plasticizer (PCE) on dynamic yield stress, thixotropy and flocculation state of fresh cement pastes in consideration of the Critical Micelle Concentration (CMC)10.1016/j.cemconres.2018.02.019 ↗
24. Measuring surface tension and free surface energy
25. Mechanisms affecting viscosity of cement paste made with microfines of manufactured sand10.1016/j.cemconres.2022.106757 ↗
26. Adsorbing polymers and viscosity of cement pastes10.1016/j.cemconres.2014.04.005 ↗
27. RILEM TC-238 SCM recommendation on hydration stoppage by solvent exchange for the study of hydrate assemblages
28. Malhotra · 2001
29. Mercury porosimetry of hardened cement pastes10.1016/S0008-8846(99)00083-6 ↗
30. The dynamics of capillary flow10.1103/PhysRev.17.273 ↗
31. Estimation of the degree of hydration of blended cement pastes by a scanning electron microscope point-counting procedure10.1016/j.cemconres.2004.01.014 ↗
32. Curing, hydration, and microstructure of cement paste
33. Netzsch-Graetebau · 2010
34. Electrical conductivity of drying cement paste10.1617/s11527-006-9211-z ↗
35. Investigation on the microstructure-related characteristics to elucidate performance of composite cement with limestone-calcined clay combination10.1016/j.cemconres.2019.105959 ↗
36. Evolution of pore structure in blended systems10.1016/j.cemconres.2015.02.025 ↗
37. Practical evaluation of resistivity of concrete in test cylinders using a Wenner array probe10.1016/S0008-8846(96)00175-5 ↗
38. Variability analysis of the bulk resistivity measured using concrete cylinders
39. Factors that influence electrical resistivity measurements in cementitious systems10.3141/2342-11 ↗
40. Time-resolved rheometry of drying liquids and suspensions10.1122/8.0000214 ↗
41. Effectiveness of shrinkage-reducing admixture in reducing autogenous shrinkage stress of ultra-high-performance fiber-reinforced concrete10.1016/j.cemconcomp.2015.09.005 ↗
42. Effects of shrinkage reducing admixture and wollastonite microfiber on early-age behavior of ultra-high performance concrete10.1016/j.cemconcomp.2013.11.008 ↗
43. Measuring plastic shrinkage and related cracking of 3D printed concretes10.1007/978-3-031-06116-5_66 ↗
44. Theory of drying10.1111/j.1151-2916.1990.tb05082.x ↗
45. Brinker · 2013
46. Influence of non-adsorbing polymers on drying of fresh mortars10.1016/j.cemconres.2018.10.016 ↗
47. Influence of shrinkage-reducing admixtures on development of plastic shrinkage cracks
48. Cellulose ethers and cement paste permeability10.1016/j.cemconres.2015.02.013 ↗
49. Permeability measurement of fresh cement paste10.1016/j.cemconres.2010.11.019 ↗
50. Moisture loss characteristics of cement-based materials under early-age drying and shrinkage conditions10.1016/j.conbuildmat.2011.11.015 ↗
51. Experimental observations of early-age drying of Portland cement paste under low-pressure conditions10.1016/j.cemconcomp.2011.01.009 ↗
52. Mix design concepts for 3D printable concrete: a review10.1016/j.cemconcomp.2021.104155 ↗
53. Hydro-mechanical properties of fresh cement pastes containing polycarboxylate superplasticizer10.1016/j.cemconres.2013.06.015 ↗
54. Manual of symbols and terminology for physicochemical quantities and units10.1351/pac197021010001 ↗
55. Effect of pore size distribution on drying shrinkage of alkali-activated slag concrete10.1016/S0008-8846(00)00327-6 ↗
56. Assessment of pore structure characteristics and tortuosity of 3D printed concrete using mercury intrusion porosimetry and X-ray tomography10.1016/j.cemconcomp.2023.105104 ↗
57. An investigation into the porosity of extrusion-based 3D printed concrete
58. The degree of hydration assessment of blended cement pastes by differential thermal and thermogravimetric analysis. Morphological evolution of the solid phases10.1016/j.tca.2014.08.008 ↗
59. Investigation of blended cement hydration by isothermal calorimetry and thermal analysis10.1016/j.cemconres.2004.10.027 ↗
60. Hydration development of mineral additives blended cement using thermogravimetric analysis (TGA): methodology of calculating the degree of hydration10.1016/j.conbuildmat.2017.04.132 ↗
61. Hydration versus strength in a Portland cement developed from domestic mineral wastes - a comparative study10.1016/0040-6031(86)85120-6 ↗
62. Characteristic lengths affecting evaporative drying of porous media10.1103/PhysRevE.77.056309 ↗
63. Numerical and experimental network study of evaporation in capillary porous media. Phase distributions10.1016/S0009-2509(96)00341-7 ↗
64. Permeability, diffusivity, and microstructural parameters: a critical review10.1016/0008-8846(90)90101-3 ↗
65. Theory of ionic-surface electrical conduction in porous media10.1103/PhysRevB.55.1757 ↗
66. Pore structure analysis by water vapor adsorption. I. t-Curves for water vapor10.1016/0021-9797(69)90132-5 ↗
67. Early-age shrinkage assessment of cementitious materials: A critical review