journal article·2017-10Open access

Mechanical behavior and microstructure of porous needle: Aluminum borate (Al18B4O33) and Al2O3-Al18B4O33 composites

María F. Hernández, Gustavo Suárez, Mariano Cipollone, Esteban F. Aglietti, Nicolás M. Rendtorff

Ceramics International· Volume 43· Issue 15

Abstract

Abstract In this article we assess and compare the complex mechanical behavior of two complex microstructure ceramics material formed within the reaction sintering framework Two comparable pairs of materials with respectively similar microstructures were obtained by reaction sintering from boric acid and alumina. Two single phase porous ceramics were compared with two composite (1:1) porous ceramic. The first and second phases were aluminum borate needles (Al18B4O33) and alumina (Al2O3). The four with comparable grain size and analogous apparent porosities: in diameter (≈ 0.7 µm) and in volume fraction (≈ 45%). The mechanical behavior was studied by means of the diametral compression test at low displacement rate and explained in terms of the texture, microstructure features evaluated by mercury intrusion porosimetry and scanning electron microscopy. Single Al18B4O33 phase porous materials presented higher mechanical strengths than the composite materials. Within the respective microstructural configurations the whisker thickness did not affect significantly the mechanical behavior and parameters. A well-defined fragile behavior was observed and described in the composite material. On the other hand the single Al18B4O33 needle porous material presented a distinctive behavior with local discontinuities without loss of integrity in the diametral stress behavior, and achieved strength up to 50% higher than the corresponding composite.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced ceramic materials synthesis · Advanced materials and composites · Bone Tissue Engineering Materials

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (45)

Show source-provided references
1. Applications of porous ceramics10.4028/www.scientific.net/KEM.122-124.305 ↗
2. Processing routes to macroporous ceramics: a review10.1111/j.1551-2916.2006.01044.x ↗
3. Macro-porous ceramics: processing and properties10.1179/1743280411Y.0000000006 ↗
4. Processing of alumina and corresponding composites10.1016/B978-0-08-096527-7.00021-0 ↗
5. Preparation and characterization of aluminum borate10.1111/j.1151-2916.1992.tb05622.x ↗
6. Acid and catalytic properties of nonstoichiometric aluminum borates10.1016/0021-9517(89)90048-1 ↗
7. Structural characterization and catalytic properties of aluminum borates–alumina catalysts10.1016/S0167-577X(98)00021-4 ↗
8. Chemical synthesis of Al18B4O33 whiskers via a combustion method10.1016/j.matlet.2007.12.017 ↗
9. Elucidating structural order and disorder phenomena in mullite-type Al 4 B 2 O 9 by automated electron diffraction tomography10.1016/j.jssc.2017.02.023 ↗
10. Formation, stability and crystal structure of mullite-type Al 6− x B x O 910.1016/j.jssc.2016.08.018 ↗
11. Effects of whisker surface treatment on microstructure and properties of Al18B4O33/6061Al composites10.1016/S1003-6326(09)60145-X ↗
12. Evaluation of strength and heat-resistance for aluminum-borate whisker reinforced AC8A aluminum alloy composite10.2464/jilm.41.270 ↗
13. Preparation and characterization of aluminum borate whisker reinforced magnesium alloy composites by semi-solid process10.1163/156855199X00254 ↗
14. Preparation of aluminum borate nanowires10.1016/j.jcrysgro.2003.11.052 ↗
15. Synthesis and microstructural characterization of aluminum borate whiskers10.1016/j.ceramint.2005.03.013 ↗
16. Synthesis and characterization of aluminum borate (Al18B4O33, Al4B2O9) nanowires and nanotubes10.1016/j.matchemphys.2005.06.023 ↗
17. Synthesis of aluminum borate nanowires via a novel flux method10.1016/j.matchemphys.2006.09.001 ↗
18. Preparation of aluminum borate whiskers by the molten salt synthesis method10.1016/j.ceramint.2013.02.007 ↗
19. Synthesis and characterization of nanostructured aluminum borate by sol–gel method10.1007/s10971-012-2833-4 ↗
20. Synthesis of aluminum borate nanorods by a low-heating-temperature solid-state precursor method10.1016/j.materresbull.2008.03.023 ↗
21. Chemical preparation of aluminum borate whiskers10.1017/S0885715600010927 ↗
22. Large-scale synthesis of Al4B2O9/Al18B4O33 whiskers via a novel method10.1016/j.matlet.2007.08.013 ↗
23. Self-catalytic growth of aluminum borate nanowires10.1016/S0009-2614(03)00930-8 ↗
24. Low-temperature synthesis of aluminum borate nanowhiskers on the surface of aluminum powder promoted by ball-milling pretreatment10.1016/j.powtec.2011.06.003 ↗
25. Glass–ceramics and composites containing aluminum borate whiskers10.1016/j.ceramint.2010.02.039 ↗
26. Microstructural differences between electrospun alumina borate nanofibers prepared by solutions with different PVP contents
27. Mineralizing alumina-magnesia cement-bonded castables containing magnesium borates10.1016/j.ceramint.2015.05.063 ↗
28. High-alumina boron-containing refractory castables10.1111/ijac.12310 ↗
29. A.P. Luz, T. Santos, J. Medeiros, V.C. Pandolfelli, Sintering additive role on the performance of advanced refractory castables, in: Proceedings of the Unified International Technical Conference on Refractories, UNITECR 2013, 2014, pp. 1099–1104.10.1002/9781118837009.ch186 ↗
30. Mullite-based refractory castable engineering for the petrochemical industry10.1016/j.ceramint.2013.05.001 ↗
31. Advanced boron-containing Al2O3-MgO refractory castables10.1111/j.1551-2916.2011.04608.x ↗
32. Boron sources as sintering additives for alumina-based refractory castables10.1016/j.ceramint.2017.05.047 ↗
33. Formation, microstructure and properties of aluminum borate ceramics obtained from alumina and boric acid10.1016/j.ceramint.2016.11.002 ↗
34. Mercury intrusion porosimetry (MIP) study of archaeological pottery from Hualfin Valley, Catamarca, Argentina10.1016/j.clay.2014.02.002 ↗
35. Fahad · J. Mater. Sci. · 1996 · 31 · 372310.1007/BF00352786 ↗
36. Review of the splitting-test standards from a fracture mechanics point of view, cement10.1016/S0008-8846(00)00425-7 ↗
37. Mechanical evaluation of cordierite precursor green bodies obtained by starch thermogelling10.1016/j.jeurceramsoc.2009.07.008 ↗
38. Thermal evolution of the mechanical properties of calcareous earthenware10.1016/j.ceramint.2013.07.067 ↗
39. Darvell · J. Mater. Sci. · 1990 · 25 · 75710.1007/BF03372161 ↗
40. Mechanical testing of cordierite porous ceramics using high temperature diametral compression10.1007/s10853-010-4472-x ↗
41. Mechanical properties of a partially sintered alumina10.1016/0955-2219(95)00045-V ↗
42. Strength and Young's modulus behavior of a partially sintered porous alumina10.1111/j.1151-2916.1995.tb08401.x ↗
43. Ultrasonic and mechanical behavior of green and partially sintered alumina: effects of slurry consolidation chemistry10.1111/j.1151-2916.1998.tb02670.x ↗
44. Permeability and infiltration of partially sintered ceramics10.1111/j.1151-2916.1999.tb02151.x ↗
45. Strength, fracture toughness and microstructure of a selection of all-ceramic materials. Part I. Pressable and alumina glass-infiltrated ceramics10.1016/j.dental.2003.05.003 ↗