journal article·2021-08

Microstructure and performance of brazed diamonds with multilayer graphene-modified Cu–Sn–Ti solder alloys

Duanzhi Duan, Feng Han, Jianjun Ding, Qijing Lin, Changsheng Li, Chenying Wang, Zhuangde Jiang

Ceramics International· Volume 47· Issue 16
Publisher page

Abstract

Abstract This study aims to improve the hardness of solidified Cu–Sn–Ti solder alloys and reduce the erosion of diamonds caused by these solder alloys during brazing. To achieve this aim, a new type of multilayer graphene-modified Cu–Sn–Ti composite solder alloy was proposed for brazing diamonds. The brazed diamond specimens were subjected to morphological observation, characterization of the interfacial microstructures. The static compressive strength and impact toughness of brazed diamond grits were measured. The Vickers microhardness of the solidified solder alloy was quantified, and the microstructure of the solidified solder alloy was also analysed. The results show that brazed diamond specimens fabricated with the No. 2 composite alloy containing 1 wt% multilayer graphene exhibited the best morphology. Addition of excess multilayer graphene reduced the flow properties of the molten Cu–Sn–Ti composite solder alloy. The dominant phases in the solidified Cu–Sn–Ti solder alloys were α-(Cu), Sn3Ti5, and CuSn3Ti5. Cu, Sn, and Ti were adsorbed by the multilayer graphene, forming C-rich and TiC-dominant phases. Consequently, erosion of the diamonds was reduced during brazing, and TiC was formed in the solidified solder alloy. Thus, increasing the content of multilayer graphene enhanced the static compressive strength and impact toughness of the brazed diamond grits, and increased the hardness of the solidified Cu–Sn–Ti solder alloy.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced materials and composites · Aluminum Alloys Composites Properties · Advanced ceramic materials synthesis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (39)

Show source-provided references
1. Microstructure and performance of brazed diamond segments with NiCr–x(CuCe) composite alloys10.1016/j.ceramint.2020.02.092 ↗
2. Interfacial characteristics and mechanical properties of the vacuum brazing diamond grains segment with Ni–Cr composite active filler and tungsten carbide reinforcement10.1016/j.jallcom.2018.12.106 ↗
3. Effect of Cu–Ce alloy addition on the microstructure and mechanical performance of brazed diamonds with Ni–Cr alloy10.1016/j.ijrmhm.2019.01.022 ↗
4. Microstructure and processing performance of brazed diamond drill bits with Ni–Cr + Cu–Ce composite solder10.1016/j.diamond.2019.01.023 ↗
5. Effects of process parameters on interfacial microstructure, residual stresses, and properties of tunnel furnace brazed diamonds10.1016/j.diamond.2018.04.003 ↗
6. Fracture behavior and self-sharpening mechanisms of polycrystalline cubic boron nitride in grinding based on cohesive element method, Chinese10.1016/j.cja.2018.11.004 ↗
7. Micro-fracture mechanism of polycrystalline CBN grain during single grain scratching tests based on fractal dimension analysis10.1016/j.precisioneng.2019.05.010 ↗
8. Investigation on microstructure characteristics and tribological properties of self-lubricating metallic composites based on hexagonal boron nitride and molybdenum disulphide10.1115/1.4047948 ↗
9. Microstructure and mechanical properties of pre-brazed diamond abrasive grains using Cu–Sn–Ti alloy10.1016/j.ijrmhm.2014.10.015 ↗
10. On bond wear, grit-alloy interfacial chemistry and joint strength of synthetic diamond brazed with Ni-Cr-B-Si-Fe and Ti activated Ag-Cu filler alloys10.1016/j.ijrmhm.2017.12.033 ↗
11. Challenges in brazing large synthetic diamond grain by Ni-based filler alloy10.1016/j.jmatprotec.2017.08.004 ↗
12. An investigation on machined surface quality and tool wear during creep feed grinding of powder metallurgy nickel-based superalloy FGH96 with alumina abrasive wheels10.1007/s40436-020-00305-2 ↗
13. The effects of solder alloys on the morphologies and mechanical properties of brazed diamond grains10.1016/j.ijrmhm.2013.10.003 ↗
14. Vacuum brazing diamond grits with Cu-based or Ni-based filler metal10.1007/s11665-017-2804-6 ↗
15. Interface characteristics and performance of pre-brazed diamond grains with Ni–Cr composite alloy10.1016/j.jallcom.2015.03.269 ↗
16. Finite element analysis of thermal effects on brazed cold diamond grain10.1007/s12666-015-0516-x ↗
17. Analysis on brazed diamond joints with modified Cu-based filler alloy10.1016/j.ijrmhm.2016.11.005 ↗
18. Abrasion resistant active braze alloys for metal single layer technology10.1179/stw.1997.2.2.71 ↗
19. Measurement of the elastic properties and intrinsic strength of monolayer graphene10.1126/science.1157996 ↗
20. The mechanics of graphene nanocomposites: a review10.1016/j.compscitech.2012.05.005 ↗
21. Graphene-copper composite with micro-layered grains and ultrahigh strength
22. Strengthening effect of single-atomic-layer graphene in metal–graphene nanolayered composites10.1038/ncomms3114 ↗
23. Enhanced strength in bulk graphene–copper composites10.1002/pssa.201330051 ↗
24. Brazing of metallized SiC ceramic to GH99 superalloy using graphene nanoplatelets reinforced AgCuTi composite filler10.1016/j.ceramint.2019.01.227 ↗
25. The microstructure and mechanical properties of C/C composite/Ti3Al alloy brazed joint with graphene nanoplatelet strengthened Ag–Cu–Ti filler10.1016/j.ceramint.2019.01.203 ↗
26. Microstructure and mechanical properties of 17-4 PH stainless steel and Al2O3 ceramic joints brazed with graphene reinforced Ag–Cu–Ti brazing alloy10.1016/j.vacuum.2020.109604 ↗
27. Vacuum brazing of GH99 superalloy using graphene reinforced BNi-2 composite filler10.1016/j.jmst.2018.02.008 ↗
28. Brazing of C/C composites to Ti6Al4V using graphene nanoplatelets reinforced TiCuZrNi brazing alloy10.1016/j.matlet.2016.07.111 ↗
29. On the tribology and grinding performance of graphene-modified porous composite-bonded CBN wheel10.1016/j.ceramint.2020.09.165 ↗
30. Effect of multilayer graphene addition on performance of brazed diamond drill bits with Ni–Cr alloy and its mechanism10.1016/j.ceramint.2020.03.242 ↗
31. Research and development of powder brazing filler metals for diamond tools: a review10.3390/met8050315 ↗
32. Processing of metal-diamond-composites using selective laser melting10.1108/RPJ-11-2014-0156 ↗
33. Experimental investigation and thermodynamic assessment of the Cu–Sn–Ti ternary system10.1016/j.calphad.2010.12.006 ↗
34. Characterization of carbon/carbon composite/Ti6Al4V joints brazed with graphene nanosheets strengthened AgCuTi filler10.1016/j.ceramint.2017.09.049 ↗
35. Graphene nanoplatelets reinforced AgCuTi composite filler for brazing SiC ceramic10.1016/j.jeurceramsoc.2018.11.046 ↗
36. Preparation of the graphene nanosheets reinforced AgCuTi based composite for brazing graphite and Cu10.1016/j.jallcom.2018.11.407 ↗
37. The effect of reinforcement percentages on properties of copper matrix composites reinforced with TiC particles10.1016/j.jallcom.2016.03.085 ↗
38. Microstructure, mechanical properties, electrical conductivity and wear behavior of high volume TiC reinforced Cu-matrix composites10.1016/j.matchar.2008.09.014 ↗
39. Electrical discharge coating of nanostructured TiC-Fe cermets on 304 stainless steel10.1016/j.surfcoat.2016.09.062 ↗