journal article·2021-10

Foaming mechanism and performance of closed–pore foamed ceramics prepared using calcium carbonate as a foaming agent

Xiangming Li, Qing Yang, Dongyue Sun, CuiCui Lv

Ceramics International· Volume 47· Issue 20
Publisher page

Abstract

Abstract The technical feasibility of preparing closed–pore foamed ceramics (FCs) at low sintering temperatures was studied, and FCs with high closed porosity were prepared by a high–temperature foaming method using calcium carbonate as the foaming agent. Rapid heating is crucial for preparing FCs. The accumulation of decomposition–derived CO2 from calcium carbonate by molten green bodies with appropriate viscosity and good continuity during sintering constitutes the foaming mechanism of FCs. During rapid heating, the surface of the green bodies rapidly melted into a whole with appropriate viscosity and good continuity. Thereafter, the increasing amount of decomposition–derived CO2 inside the green bodies was sealed by the molten surface when the temperature within the green bodies increased. The foaming performance of the FCs was improved by optimising the sintering temperature and composition of the green bodies. The FCs sintered from green bodies with 10–20 wt% calcium carbonate and 40 wt% sodium tetraborate at 750–800 °C exhibited a high total porosity of 80–82%, a high closed porosity of 76–78%, a low density of 0.48–0.53 g/cm3, a compressive strength of 2 MPa, and a uniform internal foam structure.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced ceramic materials synthesis · Polymer Foaming and Composites · Heat and Mass Transfer in Porous Media

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (30)

Show source-provided references
1. Processing routes to macroporous ceramics: a review10.1111/j.1551-2916.2006.01044.x ↗
2. Conventional and novel processing methods for cellular ceramics10.1098/rsta.2005.1683 ↗
3. Cellular ceramics: intriguing structures, novel properties, and innovative applications10.1557/mrs2003.84 ↗
4. Scheffler · 2005
5. Macroporous ceramics: processing and properties10.1179/1743280411Y.0000000006 ↗
6. Different methods to synthesize ceramic foams10.1016/j.jeurceramsoc.2008.07.039 ↗
7. Effect of fly ash cenospheres on the microstructure and properties of silica–based composites10.1016/j.ceramint.2012.01.044 ↗
8. Novel method for fabrication of silicon nitride/silicon oxynitride composite ceramic foams using fly ash cenosphere as a pore–forming agent
9. Fabrication and compressive properties of closed–cell alumina ceramics by binding hollow alumina spheres with high–temperature binder10.1016/j.ceramint.2016.07.117 ↗
10. Surface treatment of templates for fabrication of reticulated porous ceramics10.1111/j.1551-2916.2007.01830.x ↗
11. Novel mullite ceramic foams with high porosity and strength using only fly ash hollow spheres as raw material10.1016/j.jeurceramsoc.2017.11.002 ↗
12. Characterization and functionalization by sol–gel route of SiC foams10.1016/j.jeurceramsoc.2014.05.030 ↗
13. Synthesis of hierarchically porous mullite ceramics with improved thermal insulation via foam–gelcasting combined with pore former addition10.1080/17436753.2018.1502065 ↗
14. Foam–gelcasting preparation of high–strength self–reinforced porous mullite ceramics10.1016/j.jeurceramsoc.2017.05.009 ↗
15. Preparation of high strength porous mullite ceramics via combined foam–gelcasting and microwave heating10.1016/j.ceramint.2018.05.101 ↗
16. Preparation and characterization of porous mullite ceramics via foam–gelcasting10.1016/j.ceramint.2015.03.237 ↗
17. Macroporous ceramics from particle log stabilized wet foams10.1111/j.1551-2916.2006.01328.x ↗
18. Architected cellular ceramics with tailored stiffness via direct foam writing10.1073/pnas.1616769114 ↗
19. Fabrication of mullite–corundum foamed ceramics for thermal insulation and effect of micro–pore–foaming agent on their properties10.1016/j.jallcom.2019.01.212 ↗
20. Red mud and fly ash incorporation for lightweight foamed ceramics using lead–zinc mine tailings as foaming agent10.1016/j.matlet.2016.07.041 ↗
21. Effect of the CaO content and decomposition of calcium–containing minerals on properties and microstructure of ceramic foams from fly ash10.1016/j.ceramint.2017.04.122 ↗
22. Sintering behaviour and characterization of low–cost ceramic foams from coal gangue and waste quartz sand10.1080/17436753.2016.1161692 ↗
23. Preparation and characterization of novel foamed porous glass–ceramics10.1016/j.matchar.2015.03.007 ↗
24. Fabrication and characterization of ceramic foams based on silicon carbide matrix and hollow alumino–silicate spheres
25. Effects of solid distribution on the stiffness and strength of metallic foams10.1016/S1359-6454(97)00421-7 ↗
26. Preparation, microstructure, properties and foaming mechanism of a foamed ceramics with high closed porosity10.1016/j.ceramint.2019.03.091 ↗
27. Preparation and performance of electromagnetic wave absorbing foamed ceramics with high closed porosity and gradient SiC distribution10.1016/j.ceramint.2019.09.218 ↗
28. Fabrication and performance of SiO2–based electromagnetic wave penetrating foamed ceramics with dense surface10.1016/j.ceramint.2020.02.186 ↗
29. Investigation of the factors influencing the properties and structure of foamed slag glass, Glass
30. Fabrication and characterization nanostructured forsterite foams with high compressive strength, desired porosity and suitable bioactivity for biomedical applications10.1007/s10971-016-4240-8 ↗