Properties of Hf doped BaZr0.8Y0.2O3-δ protonic conductor
Source abstract
Abstract
Abstract Chemically stable BaZr0.8Y0.2O3-δ (BZY) is limited to applications because of its poor sintering behavior and low total electrical conductivity. The study aimed to enhance conductivity and sinterability for BaZr0.8Y0.2O3-δ utilizing the partial replacement of Zr4+ with Hf4+. As expected, Hf4+ was doped into the lattice and BaZr0.6Hf0.2Y0.2O3-δ (BZHY) was facilely sintered and reached a relative density above 94.79 (2)% at 1600 °C due to Hf4+ doping. The samples were quite dense with integral grains and there were no pores observed from the surface and cross-section. The samples displayed excellent chemical stability in H2, H2S, CO2 and water steam containing atmosphere even in boiling water. Thermogravimetric analysis revealed that BZHY exhibited remarkably enhanced hydration ability over BZY. The electrical conductivities of the samples in different atmospheres were investigated from 300 to 700 °C. Compared with BZY, BZHY sample displayed a higher conductivity under the same conditions due to higher relative density, bigger grain size and better hydration ability. To test the electrolyte applicability, an impedancemetric type H2 sensor consisting of ZnO sensing electrode and BZHY electrolyte was fabricated. The sensor showed excellent sensing performance and response signals varied logarithmically with the H2 concentrations in the range of 200–600 ppm at 600 °C.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advancements in Solid Oxide Fuel Cells · Electronic and Structural Properties of Oxides · Gas Sensing Nanomaterials and Sensors
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (86)
Show source-provided references
1. Microstructural adjustment of Ni-BaCe0.9Y0.1O3-δ cermet membrane for improved hydrogen permeation10.1016/j.ceramint.2013.08.066 ↗
2. Proton-conducting solid oxide fuel cells with yttrium-doped barium zirconate electrolyte films sintered at reduced temperatures10.1016/j.jallcom.2015.10.275 ↗
3. Characteristics of novel BaZr0.4Ce0.4In0.2O3 proton conducting ceramics and their application to hydrogen sensors10.1016/j.ssi.2005.09.035 ↗
4. A new family of proton‐conducting electrolytes for reversible solid oxide cells: BaHfxCe0.8-xY0.1Yb0.1O3-δ10.1002/adfm.202002265 ↗
5. Effect of Ba non-stoichiometry in Ba1-xZr0.1Ce0.7Y0.2O3-δ on its structure defect, sinterability and hydrogen permeability10.1016/j.ceramint.2020.05.012 ↗
6. Fabrication of ceramic composite anode at low temperature for high performance protonic ceramic fuel cells10.1016/j.ceramint.2019.08.256 ↗
7. Conductivity studies of dense yttrium-doped BaZrO3 sintered at 1325°C10.1016/j.jssc.2007.09.027 ↗
8. Stability and conductivity study of the BaCe0.9-xZrxY0.1O2.95 systems10.1016/j.ssi.2006.12.007 ↗
9. Proton conducting ceramics and their applications10.1016/0167-2738(96)00087-2 ↗
10. Solid-state protonic conductors: principles, properties, progress and prospects10.1016/S0167-2738(99)00152-6 ↗
11. Proton-conducting oxides10.1146/annurev.matsci.33.022802.091825 ↗
12. La2Ce2O7: a promising proton ceramic conductor in hydrogen economy10.1016/j.jallcom.2015.11.041 ↗
13. Novel modification of anode microstructure for proton-conducting solid oxide fuel cells with BaZr0.8Y0.2O3-δ electrolytes10.1016/j.jpowsour.2015.03.090 ↗
14. Fabrication and performance of a proton-conducting solid oxide fuel cell based on a thin BaZr0.8Y0.2O3-δ electrolyte membrane10.1016/j.jpowsour.2010.02.012 ↗
15. Fluoride‐based anion doping: a new strategy for improving the performance of protonic ceramic conductors of the form BaZrO310.1002/celc.202000154 ↗
16. Improvement of sinterability of BaZr0.8Y0.2O3-δ for H2 separation using Li2O/ZnO dual-sintering aid10.1016/j.ceramint.2018.06.014 ↗
17. Electrical and physical properties of composite BaZr0.85Y0.15O3-d-Nd0.1Ce0.9O2-δ electrolytes for intermediate temperature-solid oxide fuel cells10.1016/j.jpowsour.2016.11.005 ↗
18. Further optimization of barium cerate properties via co-doping strategy for potential application as proton-conducting solid oxide fuel cell electrolyte10.1016/j.jpowsour.2018.03.054 ↗
19. Enhanced sintering of yttrium-doped barium zirconate by addition of ZnO10.1111/j.1551-2916.2005.00449.x ↗
20. The effects of NiO addition on the structure and transport properties of proton conducting BaZr0.8Y0.2O3-δ10.1016/j.jallcom.2014.09.207 ↗
21. BaZr0.8Y0.2O3-δ electrolyte with and without ZnO sintering aid: preparation and characterization10.1016/j.ssi.2010.07.026 ↗
22. A new neodymium-doped BaZr0.8Y0.2O3-δ as potential electrolyte for proton-conducting solid oxide fuel cells10.1016/j.memsci.2012.05.062 ↗
23. PdO-doped BaZr0.8Y0.2O3-δ electrolyte for intermediate-temperature protonic ceramic fuel cells10.1016/j.actamat.2013.11.014 ↗
24. Densification and properties of barium zirconate ceramics by addition of P2O510.1016/j.matlet.2009.12.003 ↗
25. Structural and electrochemical properties of yttrium-doped barium zirconate by addition of CuO10.1016/j.jallcom.2009.12.082 ↗
26. Effect of grain size on the electrical performance of BaZr0.1Ce0.7Y0.1Yb0.1O3-δ solid electrolytes with addition of NiO10.1016/j.ceramint.2018.09.217 ↗
27. Lowering grain boundary resistance of BaZr0.8Y0.2O3-δ with LiNO3 sintering-aid improves proton conductivity for fuel cell operation10.1039/C0CP01470B ↗
28. An easily sintered, chemically stable, barium zirconate-based proton conductor for high-performance proton-conducting solid oxide fuel cells10.1002/adfm.201401478 ↗
29. Chemically stable Pr and Y Co-doped barium zirconate electrolytes with high proton conductivity for intermediate-temperature solid oxide fuel cells10.1002/adfm.201001540 ↗
30. Does the increase in Y-dopant concentration improve the proton conductivity of BaZr1-xYxO3-δ fuel cell electrolytes?10.1016/j.ssi.2010.06.007 ↗
31. The relationship between chemical composition distributions and specific grain boundary conductivity in Y-doped BaZrO3 proton conductors10.1016/j.ssi.2008.12.006 ↗
32. Structure, sinterability, chemical stability and conductivity of proton-conducting BaZr0.6M0.2Y0.2O3-δ electrolyte membranes: the effect of the M dopant10.1016/j.memsci.2014.05.020 ↗
33. Tailoring mixed proton-electronic conductivity of BaZrO3 by Y and Pr co-doping for cathode application in protonic SOFCs10.1016/j.ssi.2011.08.019 ↗
34. Chemically stable Dy-Y double substituted barium zirconate with high proton conductivity and improved sinterability10.1016/j.jallcom.2015.04.084 ↗
35. Effect of low-level Ca2+ substitution at perovskite B site on the properties of BaZr0.8Y0.2O3-δ10.1016/j.jallcom.2019.07.128 ↗
36. Combined bulk and surface analysis of the BaCe0.5Zr0.3Y0.16Zn0.04O3-δ (BCZYZ) ceramic proton-conducting electrolyte10.1016/j.ssi.2013.12.044 ↗
37. Synthesis, stability and conductivity of BaCe0.8-xZrxY0.2O3-δ as electrolyte for proton conducting SOFC10.1016/j.ijhydene.2011.04.106 ↗
38. Protonic-electronic mixed conduction and hydrogen permeation in BaCe0.90-xY0.1RuxO3-α10.1149/1.1852442 ↗
39. Synthesis, sintering behavior and electrical properties of Ba(Zr0.1Ce0.7Y0.2)O3-δ and Ba(Zr0.1Ce0.7Y0.1Yb0.1)O3-δ proton conductors10.1016/j.ceramint.2014.06.115 ↗
40. Sintering, chemical stability and electrical conductivity of the perovskite proton conductors BaCe0.45Zr0.45M0.1O3-δ (M=In, Y, Gd, Sm)10.1016/j.jallcom.2007.12.103 ↗
41. Structural and conductivity study of the proton conductor BaCe(0.9-x)ZrxY0.1O(3-δ) at intermediate temperatures10.1016/j.jpowsour.2008.11.080 ↗
42. Chemical stability and proton conductivity of doped BaCeO3-BaZrO3 solid solutions10.1016/S0167-2738(99)00196-4 ↗
43. Chemical stability of doped BaCeO3-BaZrO3 solid solutions in different atmospheres10.1016/S1002-0721(08)60127-1 ↗
44. Protonic conduction in Zr-substituted BaCeO310.1016/S0167-2738(00)00777-3 ↗
45. Effect of Zn addition on the structure and electrochemical properties of co-doped BaCe0.6Zr0.2Ln0.2O3-δ (Ln=Y, Gd, Yb) proton conductors10.1016/j.ceramint.2018.05.010 ↗
46. Fabrication of high-performance proton-conducting electrolytes from microwave prepared ultrafine powders for solid oxide fuel cells10.1016/j.jpowsour.2018.11.051 ↗
47. Introduction of in or Ga as second dopant to BaZr0.9Y0.1O3-δ to achieve better sinterability10.1016/j.ssi.2008.02.047 ↗
48. Sintering behaviour of the protonic conductors BaZrxCe0.8-xLn0.2O3-δ (x=0.8, 0.5, 0.1; Ln=Y, Sm, Gd, Dy) during the solid-state reactive-sintering process10.1016/j.ceramint.2014.10.177 ↗
49. New Gd-Zn co-doping enhanced mechanical properties of BaZrO3 proton conductors with high conductivity for IT-SOFCs10.1016/j.mseb.2018.12.012 ↗
50. Nanograined Sc-doped BaZrO3 as a proton conducting solid electrolyte for intermediate temperature solid oxide fuel cells (IT-SOFCs)10.1016/j.ssi.2014.06.010 ↗
51. Proton conductivity in perovskite type yttrium doped barium hafnate10.1016/j.scriptamat.2004.08.021 ↗
52. Transport properties of proton conductive Y-doped BaHfO3 and Ca or Sr-substituted Y-doped BaZrO310.1111/jace.15946 ↗
53. Chemically stable yttrium and tin Co-doped barium zirconate electrolyte for next generation high performance proton-conducting solid oxide fuel cells10.1002/aenm.201201062 ↗
54. Structure and electrical conductivity of BaCe0.85Ln0.15O3-δ (Ln=Gd, Y, Yb) ceramics10.1016/j.electacta.2013.05.034 ↗
55. Influence of rare-earth doping on the microstructure and conductivity of BaCe0.9Ln0.1O3-δ proton conductors10.1016/j.jpowsour.2010.11.120 ↗
56. Recent activity in the development of proton-conducting oxides for high-temperature applications10.1039/C6RA13347A ↗
57. Influence of in content on the electrical conduction behavior of Sm- and In-co-doped proton conductor BaCe0.80-xSm0.20InxO3-δ10.1016/j.ssi.2011.10.026 ↗
58. Raman scattering study of acceptor-doped BaCeO310.1016/0167-2738(93)90339-5 ↗
59. Temperature-dependent structures of proton-conducting Ba(Zr0.8-xCexY0.2)O2.9 ceramics by Raman scattering and x-ray diffraction10.1088/0953-8984/24/15/155403 ↗
60. Raman scattering study of phase transitions in undoped and rare earth ion-doped BaCeO3 and SrCeO310.1002/jrs.1250241114 ↗
61. Raman spectroscopy of perovskite-type BaCexZr1-xO3 (0≤x≤1)10.1006/jssc.1998.8038 ↗
62. CO2-tolerant oxygen separation membranes targeting CO2 capture application10.1016/j.memsci.2009.03.012 ↗
63. Optical basicity and O1s binding energy of simple oxides10.2109/jcersj.107.21 ↗
64. Electronic polarizability, optical basicity and XPS spectra of Sb2O3-B2O3 glasses10.1016/S0022-3093(00)00156-3 ↗
65. Aspects of the formation and mobility of protonic charge carriers and the stability of perovskite-type oxides10.1016/S0167-2738(99)00188-5 ↗
66. On the development of proton conducting materials for technological applications10.1016/S0167-2738(97)00082-9 ↗
67. Hafnium salts of dodeca-tungstophosphoric acid catalysts for liquid phase benzylation of anisole with dibenzylether10.1016/j.apcata.2013.11.001 ↗
68. Preparation of highly dispersed and thermally stable nanosized cerium–hafnium solid solutions over silica surface: structural and catalytic evaluation10.1016/j.jiec.2012.01.017 ↗
69. Mild hydrothermal syntheses and thermal behaviors of hydrogarnets Sr3M2(OH)12 (M=Cr, Fe, and Al)10.1021/cm9702373 ↗
70. Hydrothermal synthesis and properties of Ce1-xSmxO2-x/2 and Ce1-xCaxO2-x solid solutions10.1021/cm970425t ↗
71. Acceptor doping effects on microstructure, thermal and electrical properties of proton-conducting BaCe0.5Zr0.3Ln0.2O3-δ (Ln = Yb, Gd, Sm, Nd, La or Y) ceramics for solid oxide fuel cell applications10.1016/j.electacta.2016.01.144 ↗
72. Effect of Ba nonstoichiometry on the phase structure, sintering, electrical conductivity and phase stability of Ba1±xCe0.4Zr0.4Y0.2O3-δ (0≤x≤0.20) proton conductors10.1016/j.ijhydene.2011.04.037 ↗
73. Effect of Ba nonstoichiometry on the phase composition, microstructure, chemical stability and electrical conductivity of BaxCe0.7Zr0.1Y0.1Yb0.1O3-δ (0.9≤x≤1.1) proton conductors10.1016/j.ceramint.2015.02.113 ↗
74. Study on stability and electrical performance of yttrium and bismuth co-doped BaCeO310.1016/j.ceramint.2012.11.083 ↗
75. A review on proton conducting electrolytes for clean energy and intermediate temperature-solid oxide fuel cells10.1016/j.rser.2017.05.147 ↗
76. Stable and easily sintered BaCe0.5Zr0.3Y0.2O3-δ electrolytes using ZnO and Na2CO3 additives for protonic oxide fuel cells, Electrochim
77. Electrochemical properties and intermediate-temperature fuel cell performance of dense yttrium-doped barium zirconate with calcium addition10.1111/j.1551-2916.2011.04795.x ↗
78. Enhanced proton conduction of BaZr0.9Y0.1O3-δ by hybrid doping of ZnO and Na3PO410.1016/j.ssi.2015.08.009 ↗
79. Influence of ZnO addition on the properties of high temperature proton conductor Ba1.03Ce0.5Zr0.4Y0.1O3-δ synthesized via citrate-nitrate method10.1016/j.ijhydene.2009.01.061 ↗
80. Chemical stability of Y-doped Ba(Ce,Zr)O3 perovskites in H2S-containing H210.1016/j.electacta.2007.12.020 ↗
81. Chemically stable and easily sintered high-temperature proton conductor BaZr0.8In0.2O3-δ for solid oxide fuel cells10.1016/j.jpowsour.2012.12.017 ↗
82. Conductivity recovery by redox cycling of yttrium doped barium zirconate proton conductors and exsolution of Ni-based sintering additives10.1016/j.jpowsour.2016.11.036 ↗
83. Effects of Ni doping on the sintering and electrical properties of BaZr0.8Y0.2O3-δ proton conducting electrolyte prepared by Flame Spray Synthesis10.1016/j.jeurceramsoc.2015.09.010 ↗
84. Impedancemetric NO2 sensor based on Pd doped perovskite oxide sensing electrode conjunction with phase angle response10.1016/j.electacta.2018.01.205 ↗
85. Impedancemetric NOx sensing using YSZ electrolyte and YSZ/Cr2O3 composite electrodes10.1149/1.2430646 ↗
86. High-temperature NO2 sensor based on aluminum/indium co-doped lanthanum silicate oxyapatite electrolyte and cobalt-free perovskite oxide sensing electrode10.1016/j.snb.2017.05.010 ↗