Relating residual stresses to machining and finishing in silicon carbide
Source abstract
Abstract
Abstract Machining and surface finishing is essential in the processing of many ceramics, however, it can be detrimental to subsequent performance as it introduces residual stresses and structural defects. Using micro-Raman spectroscopy the residual stress and crystallinity of hot-pressed SiC tiles were examined after finishing with several different methods. 514 nm and 633 nm lasers in both conventional and confocal settings enabled stress as a function of depth to be assessed. Single crystal, electronics grade SiC was used for comparison. Compressive residual stresses were present at the surface and in the sub-surface region in all the samples, but the surface with lowest roughness and a mirror-like finish had the highest residual stress. Crystallinity in SiC is reduced by defects and stacking faults produced during machining and finishing. The finer surface finishes had higher residual stresses, but were actually found to have better crystallinity than the rough surfaces. The dependence of residual stress and crystallinity on surface roughness is attributed to a change in the mode of ceramic removal from energetic and brittle for rough finishes to ductile for the shallow cuts of smooth finishes. The dependence of stress and crystallinity on roughness means a balance must be struck between smoothness, crystallinity and stresses in choosing the best finish for a given application.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced Surface Polishing Techniques · Advanced ceramic materials synthesis · Integrated Circuits and Semiconductor Failure Analysis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (39)
Show source-provided references
1. Silicon carbide based hard materials
2. Marinescu · 2007
3. On the crystal structure of silicon carbide and its content of impurities10.3891/acta.chem.scand.02-0177 ↗
4. Saddow · 2004
5. Raman modes of 6H polytype of silicon carbide to ultrahigh pressures: a comparison with silicon and diamond10.1103/PhysRevLett.72.4105 ↗
6. Raman modes of 6H polytype of silicon carbide to ultrahigh pressures – reply10.1103/PhysRevLett.77.1661 ↗
7. Defect formation mechanism of bulk SiC10.4028/www.scientific.net/MSF.264-268.41 ↗
8. Defect analysis in lely-grown 6H SiC10.1016/0022-0248(96)00188-1 ↗
9. Characterization of defects in silicon carbide by Raman spectroscopy10.1002/pssb.200844052 ↗
10. Silicon carbide: synthesis and processing10.1016/0168-583X(96)00065-1 ↗
11. Raman study on residual strains in thin 3C–SiC epitaxial layers grown on Si(001)10.1016/S0040-6090(00)00789-6 ↗
12. Residual stress fields in surface-treated silicon carbide for space industry—comparison of biaxial and triaxial analysis using different X-ray methods10.1016/j.msea.2004.08.018 ↗
13. Ferraro · 2003
14. Comparative optical investigations of sintered and monocrystalline black and green silicon carbide (SiC)10.1016/j.jssc.2003.04.006 ↗
15. In-depth analyses by confocal Raman microspectrometry: experimental features and modeling of the refraction effects10.1002/jrs.915 ↗
16. Experimental challenges of stress measurements with resonant micro-Raman spectroscopy10.1002/(SICI)1097-4555(199910)30:10<893::AID-JRS468>3.0.CO;2-3 ↗
17. Analysis of strain and stress in ceramic, polymer and metal matrix composites by Raman spectroscopy10.1002/1527-2648(20020806)4:8<535::AID-ADEM535>3.0.CO;2-E ↗
18. Strain-fluctuation effect on Raman spectra10.1103/PhysRevB.55.R14697 ↗
19. Raman spectroscopy of nanomaterials: how spectra relate to disorder, particle size and mechanical properties10.1016/j.pcrysgrow.2007.01.001 ↗
20. Morphic effects in lattice dynamics10.1016/B978-0-444-85315-8.50007-4 ↗
21. Piezo-spectroscopy: a materials science perspective
22. Raman line widths of optical phonons in 3C–SiC under pressure: first-principles calculations and experimental results10.1103/PhysRevB.59.6774 ↗
23. Raman determination of layer stresses and strains for heterostructures and its application to the cubic SiC/Si system10.1063/1.341997 ↗
24. Measurement of scratch-induced residual stress within SiC grains in ZrB2–SiC composite using micro-Raman spectroscopy10.1016/j.actamat.2008.07.031 ↗
25. Raman microprobe mapping of residual microstresses in 3C–SiC film epitaxial lateral grown on patterned Si(111)10.1016/j.apsusc.2004.01.052 ↗
26. Pressure dependence of Raman phonons of Ge and 3C–SiC10.1103/PhysRevB.25.1151 ↗
27. Raman scattering of SiC: estimation of the internal stress in 3C–SiC on Si10.1063/1.339191 ↗
28. Raman scattering study of stress distribution around dislocation in SiC
29. Raman piezospectroscopy of phonons in bulk 6H–SiC10.12693/APhysPolA.116.947 ↗
30. Raman investigation of SiC polytypes10.1002/1521-396X(199707)162:1<39::AID-PSSA39>3.0.CO;2-L ↗
31. Raman imaging of semiconductor materials: characterization of static and dynamic properties
32. Depth profiling with confocal Raman microscopy, part I
33. Depth profiling with confocal Raman microscopy, part II
34. Confocal Raman microscopy: performance, pitfalls, and best practice10.1366/000370209789379196 ↗
35. Raman scattering as a probing method of subsurface damage in SiC10.1016/S0921-5107(00)00596-1 ↗
36. Sample-probe interactions in spectroscopy: sampling microscopic property gradients10.1063/1.358885 ↗
37. Nanoscale residual stress-field mapping around nanoindents in SiC by IR s-SNOM and confocal Raman microscopy10.1364/OE.17.022351 ↗
38. Micro-Raman spectroscopy to study local mechanical stress in silicon integrated circuits10.1088/0268-1242/11/2/001 ↗
39. Ductile-regime grinding: a new technology for machining brittle materials10.1115/1.2899676 ↗