Dry sliding wear characteristics of carbon nanotube/alumina nanocomposites under a sharp pyramidal indenter
Source abstract
Abstract
Abstract Hot-pressed multiwalled carbon nanotube (MWCNT)/alumina (Al2O3) nanocomposites offered improved flexural strength (σ4–FS), hardness (HV) and fracture toughness (KIC–SENB) over pure Al2O3. While HV and σ4-FS of nanocomposites improved by 8–10%, KIC-SENB of 0.13 wt% CNT/Al2O3 nanocomposite (~7.45 MPa m0.5) was ~1.3 and ~2.1 times higher than hot-pressed and pressureless sintered Al2O3, respectively. Unlubricated sliding wear experiments at 1–20 N normal load (FN) under a sharp pyramidal indenter revealed enhanced resistance to catastrophic failure and wear of nanocomposites over pure Al2O3. At FN=20 N, the lowest wear rate (WR≈0.02 mm3/N m) of 0.07 wt% CNT/Al2O3 nanocomposite was found to be ~50% lower than that of monolithic Al2O3. Scratch tests on ground and polished samples revealed notable changes in WR and wear mode as a function of surface roughness (Ra). Wear mode maps indicated that while in ground specimens the primary mechanism was excessive flake formation, severity of flake formation reduced significantly in polished samples and turned toward powder formation and/or ploughing due to effective indenter tip/specimen surface interaction in absence of stochastic surface irregularities present in ground samples. Present study indicated that for characteristic wear analysis of CNT/Al2O3 nanocomposites, Ra should be ≤100 nm.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Tribology and Wear Analysis · Advanced materials and composites · Metal and Thin Film Mechanics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (28)
Show source-provided references
1. Wear mechanisms in brittle solids10.1016/0956-7151(92)90455-N ↗
2. Wear and friction behaviour of self-lubricating alumina–zirconia–fluoride composites fabricated by the PECS technique10.1016/j.ceramint.2013.06.068 ↗
3. Experimental study on microscopic wear mechanism of copper/carbon/rice bran ceramics composites10.1016/j.wear.2012.07.004 ↗
4. Tribological properties of hot-pressed alumina–CNT composites10.1016/S0043-1648(03)00216-3 ↗
5. Effect of CNT distribution on tribological behaviour of alumina–CNT composites10.1016/j.wear.2005.02.031 ↗
6. Scratch deformation behaviour of alumina under a sharp indenter10.1016/S0955-2219(96)00081-7 ↗
7. A new scratch resistance measure for structural ceramics10.1111/j.1551-2916.2005.00181.x ↗
8. Sensitivity of scratch resistance to grinding-induced damage anisotropy in silicon nitride10.1111/j.1551-2916.2006.01073.x ↗
9. Ductile to brittle transition depth during single-grit scratching on alumina ceramics10.1111/j.1551-2916.2007.01970.x ↗
10. Deformation of ceria-stabilized tetragonal Zirconia ceramics in scratch experiments with a sharp indenter10.1016/0955-2219(94)90053-1 ↗
11. Recent developments in wear mechanism maps10.1016/S0301-679X(98)00011-5 ↗
12. Role of interface on electrical conductivity of carbon nanotube/alumina nanocomposite10.1016/j.ceramint.2013.10.049 ↗
13. Mechanical properties and electrical conductivity of alumina/MWCNT and alumina/zirconia/MWCNTcomposites10.1016/j.ceramint.2013.07.008 ↗
14. Wear resistance of Al2O3–CNT ceramic nanocomposites at room and high temperatures10.1016/j.ceramint.2012.12.100 ↗
15. Electrical conductivity and microwave absorption of shortened multi-walled carbon nanotube/alumina ceramic composites10.1016/j.ceramint.2012.12.057 ↗
16. Synthesis and characterization of pressureless sintered carbon nanotube reinforced alumina nanocomposites10.1016/j.msea.2013.04.020 ↗
17. Temperature and load dependent mechanical properties of pressureless sintered carbon nanotube/alumina nanocomposites10.1016/j.msea.2011.10.024 ↗
18. Tribological and electrical properties of ceramic matrix composites with carbon nanotubes10.1016/j.ceramint.2012.04.010 ↗
19. Highly concentrated 3D macrostructure of individual carbon nanotubes in a ceramic environment10.1002/adma.201201134 ↗
20. Hard and tough carbon nanotube-reinforced zirconia-toughened alumina composites prepared by spark plasma sintering10.1016/j.carbon.2011.09.031 ↗
21. Mechanical and electrical properties of multiwalled CNT-alumina nanocomposites prepared by a sequential two-step processing of ultrasonic spray pyrolysis and spark plasma sintering10.1111/j.1551-2916.2011.04689.x ↗
22. An elastic-plastic-cracking model for finite element analysis of indentation cracking in brittle materials10.1016/S0020-7683(00)00406-6 ↗
23. Effect of sintering temperature on a single-wall carbon nanotube-toughened alumina-based nanocomposite10.1016/j.scriptamat.2007.02.007 ↗
24. A novel structure for carbon nanotube reinforced alumina composites with improved mechanical properties10.1088/0957-4484/19/31/315708 ↗
25. Pressureless sintering of carbon nanotube–Al2O3 composites10.1016/j.jeurceramsoc.2009.12.005 ↗
26. Nanotube fracture during the failure of carbon nanotube/alumina composites10.1016/j.carbon.2011.04.022 ↗
27. Improved sliding wear-resistance of alumina with sub-micron grain size: a comparison with coarser grained material10.1016/j.jeurceramsoc.2007.02.205 ↗
28. (MTS Systems Corporation, Eden Prairie, MN, US)