journal article·2012-01

Effect of forming process on the integrity of pore-gradient Al2O3 ceramic foams by gelcasting

Xinshuang Guo, Zhufa Zhou, Guilin Ma, Shumei Wang, Song Zhao, Qiang Zhang

Ceramics International· Volume 38· Issue 1
Publisher page

Abstract

Abstract Pore-gradient Al 2 O 3 foams were produced by gelcasting using the epispastic polystyrene (EPS) sphere template. This approach allows the design of porous ceramics with degree of pore connectivity and height of gradient layers via appropriate selection of the sizes and numbers of spheres. The fabrication processing of open-cell porous ceramics limited by polymeric sponge template, sharp cracks at the strut edges and closed pores can be resolved by this approach. To achieve the optimal manufacturing conditions of maintaining integrity of the network, the effects of solid loads, height of the slurry and the pre-removal of the polymeric foam template on the struts of the ceramic foams were studied. The results revealed that 55 vol.% Al 2 O 3 slurries with 0.5 wt.% ammonium polyacrylate kept good fluidity for casting and avoided the inner inordinate shrinkage. Different shrinkage behavior of the top and bottom of the sample was effectively reduced due to approximately same water vapor diffusion areas on the top and bottom. The integrity of dendritic solidification structure maintained perfectly through template pre-removed in dichloromethane compared with direct heating.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced ceramic materials synthesis · Advanced materials and composites · Bone Tissue Engineering Materials

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (26)

Show source-provided references
1. Mechanical properties of cellular ceramics obtained by gel casting: characterization and modeling10.1016/j.jeurceramsoc.2009.04.035 ↗
2. Different methods to synthesize ceramic foams10.1016/j.jeurceramsoc.2008.07.039 ↗
3. Grading porous ceramics by centrifugal sintering10.1016/S1359-6454(03)00143-5 ↗
4. Synthesis of BaTiO3 core–shell particles and fabrication of dielectric ceramics with local graded structure10.1021/cm060403j ↗
5. Graded open-cell aluminium foam core sandwich beams10.1016/j.msea.2005.05.096 ↗
6. Porous mullite composite with controlled pore structure processed using a freeze casting of TBA-based coal fly ash slurries10.1016/j.resconrec.2009.12.012 ↗
7. Ceramic composite components with gradient porosity by powder injection moulding10.1016/j.matdes.2009.12.030 ↗
8. Preparation of Al2O3 and Al2O3–ZrO2 ceramic foams with adjustable cell structure by centrifugal slip casting10.1016/j.msea.2007.04.100 ↗
9. Processing routes to macroporous ceramics: a review10.1111/j.1551-2916.2006.01044.x ↗
10. Behaviour of open-cell cordierite foams under compression10.1016/j.jeurceramsoc.2004.10.008 ↗
11. Gas-filled microspheres as an expandable sacrificial template for direct casting of complex-shaped macroporous ceramics10.1016/j.jeurceramsoc.2008.04.020 ↗
12. Gelation process in low-toxic gelcasting systems10.1016/j.jeurceramsoc.2005.08.020 ↗
13. Hierarchical pore structure of calcium phosphate scaffolds by a combination of gel-casting and multiple tape-casting methods10.1016/j.actbio.2008.02.005 ↗
14. New methods to remove organic templates from porous materials10.1016/S0254-0584(01)00557-0 ↗
15. Removal of organic templates from mesoporous SBA-15 at room temperature using UV/dilute H2O210.1016/j.micromeso.2006.07.019 ↗
16. Supercritical fluid extraction of a nonionic surfactant template from SBA-15 materials and consequences on the porous structure10.1021/la026970c ↗
17. Evaluation of the efficiency of solvent extraction for template removal in the synthesis of MCM-41 type materials to be used as tobacco additives for smoke toxicity reduction10.1016/j.apcata.2010.02.006 ↗
18. Microwave assisted template removal of siliceous porous materials10.1039/b202180c ↗
19. Modification of PS films by combined treatment of ozone aeration and UV irradiation in aqueous ammonia solution for the introduction of amine and amide groups on their surface10.1016/j.apsusc.2004.12.017 ↗
20. Controllable growth of gradient porous structures10.1021/bm900008d ↗
21. Rheology of soft glassy materials10.1103/PhysRevLett.78.2020 ↗
22. Uhlmann · 1992
23. A physical model for the drying of gelcast ceramics10.1111/j.1151-2916.1999.tb01795.x ↗
24. Aggregation effects on the compressive flow properties and drying behavior of colloidal silica suspensions10.1111/j.1151-2916.1999.tb02090.x ↗
25. Models for predicting drying stresses and strains in a film cast on a substrate: an alternative approach10.1016/j.ces.2008.12.023 ↗
26. Effects of adhesive type and polystyrene concentration on the shear strength of bonded polystyrene/high-density polyethylene blends10.1016/j.ijadhadh.2005.02.001 ↗