journal article·2013-08

Degradation behavior of 4D carbon/carbon composites under supersonic oxidative air plasma

Shameel Farhan, Noaman Ul-Haq, Wen-Shyong Kuo

Ceramics International· Volume 39· Issue 6
Publisher page

Abstract

Abstract Four-directional (4D) carbon/carbon (C/C) composites were prepared using an intermediate modulus carbon fiber as the reinforcement and two kinds of coal tar pitches as the source for carbon matrix. After repeated high-pressure impregnation, carbonization and graphitization at 2250 °C, a high density of 1.86 g/cm3 was achieved. A plasma arc jet was applied to the composite for studying its degradation behavior. The oxidative supersonic jet was generated by an air plasma torch. For studying various stages of degradation during a long exposure time of 90-s, the intermittent ablation and erosion rates were measured for the C/C composite at time intervals of 70, 50 and 30 s. The mass ablation rate was increased rapidly with the time, while the erosion showed a bilinear response with a decreasing trend. The results were discussed based on the machined and eroded surfaces of the test samples. For studying the residual ablative performance, the samples of 30–70 s were then re-ablated and re-eroded in steps of 20-s so that all the samples are equal in total exposure time. The samples showed decreasing trends in the re-ablation and re-erosion rates and ultimately became zero for the last 20-s exposure time. There was a progressive increase in the char layer on the samples with the re-ablation. The porous char layer protected the samples against chemical and mechanical actions of the plasma stream. Compressive tests were carried out, and the decrease in the modulus was due to the presence of microcracks resulting from the mismatch in thermal expansion of the fiber and the matrix. The SEM micrographs reveal that inter- and intra-bundle cracks tend to grow through the weaker matrix pockets.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced ceramic materials synthesis · Diamond and Carbon-based Materials Research · Fiber-reinforced polymer composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (32)

Show source-provided references
1. Savage · 1993
2. G.A. Rozak, Mechanical Behavior of Carbon–Carbon Composites, NASA Contractor Report ♯174767, (1984).
3. Identification of the non-linear behavior a 4D carbon–carbon material designed for aeronautic application10.1023/A:1012697425426 ↗
4. Ablation of the carbon/carbon composite nozzle-throats in a small solid rocket motor10.1016/j.carbon.2010.11.037 ↗
5. Modeling of the mechanical behavior of 4D carbon/carbon composite materials10.1016/S0266-3538(97)00181-4 ↗
6. A novel thermal gradient chemical vapor infiltration process for carbon–carbon composites10.1016/S1872-5805(07)60020-1 ↗
7. Damage modeling of a 4D carbon/carbon composite for high temperature application10.1016/S0272-8842(99)00108-X ↗
8. An inelastic finite element model of 4D carbon–carbon composites10.2514/3.8218 ↗
9. Recent improvements in 4D carbon–carbon materials
10. A theoretical/experimental approach to the intrinsic oxidation reactivities of C/C composites and of their components10.1016/j.carbon.2007.09.034 ↗
11. Investigation on ablation behavior of CFRC composites prepared at different pressure10.1016/j.compositesa.2004.03.024 ↗
12. R.Z. Li, Y.D. Li, J.M. Su, H. Cui, Z.A. Su, S.J. Zhou, Study of the properties of axial rod 4D woven C/C composite, Extended abstracts, Eurocarbon 98, Strasbourg, France: Science and Technology of Carbon, (1998).
13. Oxidation and ablation of 3D carbon–carbon composite at up to 3000°C10.1016/0008-6223(94)00172-V ↗
14. Oxidation microstructure studies of reinforced carbon/carbon10.1016/j.carbon.2005.11.013 ↗
15. Erosion resistance of needled carbon/carbon composites exposed to solid rocket motor plumes10.1016/j.carbon.2009.01.040 ↗
16. Microstructural interpretation of the effect of various matrices on the ablation properties of carbon fiber reinforced composites10.1016/S0266-3538(00)00212-8 ↗
17. Microstructure and ablation performances of dual-matrix carbon/carbon composites10.1016/j.carbon.2006.01.017 ↗
18. Effects of ablation at different regions in three-dimensional orthogonal C/SiC composites ablated by oxyacetylene torch at 1800°C10.1016/j.jmatprotec.2008.08.002 ↗
19. Effect of density and fiber orientation on the ablation behavior of carbon–carbon composites10.1016/S1872-5805(09)60023-8 ↗
20. Thermal response and ablation characteristics of carbon fiber reinforced composite with novel silicon containing polymer MSP10.1177/0021998302036002554 ↗
21. Ablation behavior of ultra-high temperature ceramics composites10.1016/j.msea.2007.02.040 ↗
22. Ablation behaviors of carbon/carbon composites with C–SiC–TaC multi-interlayers10.1016/j.apsusc.2009.07.006 ↗
23. Degradation of carbon-based materials under ablative conditions produced by a high enthalpy plasma jet10.5028/jatm.2010.02013340 ↗
24. ACS symposium series 599
25. Fitzer · 1998
26. Effects of pressure on the pore formation of carbon/carbon composites during carbonization10.1023/A:1004674213884 ↗
27. The effect of modification of matrix on densification efficiency of pitch based carbon composites10.1007/s12404-010-0414-y ↗
28. A comprehensive theoretical model for carbon–carbon composite nozzle recession
29. F.S. Milos, Y.K. Chen, Comprehensive model for multicomponent ablation thermochemistry, in: Proceedings of the 35th Aerospace Science Meeting and Exhibit, AIAA, Reno, NV, (1997).10.2514/6.1997-141 ↗
30. Dynamic compressive behavior of unidirectional IM7/5250-4 laminate after thermal oxidation10.1016/j.compscitech.2011.10.012 ↗
31. Comparison of 2D and 3D carbon/carbon composites with respect to damage and fracture resistance10.1016/S0008-6223(02)00442-6 ↗
32. Compressive strength of three-dimensionally reinforced carbon/carbon composites10.1016/j.carbon.2004.09.026 ↗